ReferenceDesignLibrary

Refine Search

Eval Board Voltage In Topology Current Out Voltage Out (Max) Outputs and Type Efficiency @ Conditions Features Switching Frequency Component Count + Extras Design Author Application / Target Market Main I.C. Base Part
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (147)

147 Results - Page 1/15 |< < 1 2 3 4 5 > >|

LM3464EVAL: 4 Channel @ 350 mA/chan, 12~80V in

Manufacturer: Texas Instruments

This evaluation board demonstrates the high power efficiency and outstanding output current accuracy of the LM3464A typical application circuit. With four LED strings connected, the total output power is about 50W. The schematic, bill of material and PCB layout drawing of the LM3464A evaluation board are provided in this document.

This evaluation board can be adapted to different ty…

View Design

TPS61150EVM-150: 4 LEDs x 2 @ 15mA, 2.5 ~ 6V in

Manufacturer: Texas Instruments

The Texas Instruments TPS61150EVM-150 evaluation module contains the TPS61150 IC. This EVM provides two independently regulated current outputs using a single inductor step-up (boost) converter.

View Design

EVL6562A-LED: 350mA @ 45V Max, 36 ~ 60V in

Manufacturer: STMicroelectronics

Whenever a lighting application, such as street lighting for example, requires an elevated number of LEDs, there are basically two solutions: the first is to connect all the diodes in series in a single "string"; the second is to place several strings in parallel with fewer elements in each one.

The first solution, even if simpler, poses stringent safety requirements due to the high …

View Design

LM3401-MR16DEMO: 1A @ 6.2V Max, 12VAC, MR16

Manufacturer: Texas Instruments

This design was developed to minimize the current spikes coming out of an electronic transformer to less than 5A, which is a typical transformer rating, when driving an LED MR16 circuit. The off the shelf LED MR16 solutions exhibit spikes that significantly exceed a transformers maximum rated output current which will degrade the reliability of the transformer and reduce its operating lifetime. T…

View Design

CAT4201AGEVB: 350mA @ 20V Max, 6.5 ~ 28V in

Manufacturer: ON Semiconductor

The CAT4201 is a high efficiency step-down LED driver from Catalyst Semiconductor. This device is designed to drive high brightness LEDs up to 350mA from a power supply up to 28V. The LED brightness is controlled by a single resistor from the RSET pin to GND. Analog dimming and idle mode control are available through the CTRL input. An external circuit is provided on the CAT4201AEVB for PWM dimmin…

View Design

STEVAL-ILL008V1: 1 LED @ 280mA, 0.6 ~ 5.5V in

Manufacturer: STMicroelectronics

The L6920D is used in this flashlight application as it is a high efficiency step-up controller that realizes the conversion from battery voltage to the selected output voltage with only three external components.

View Design

LM3409HVEVAL: 1.5A @ 42V Max, 48V in

Manufacturer: Texas Instruments

This evaluation board showcases the LM3409HV PFET controller for a buck current regulator. It is designed to drive 12 LEDs (VO = 42V) at a maximum average LED current (ILED = 1.5A) from a DC input voltage (VIN = 48V). The switching frequency (fSW = 400 kHz) is targeted for the nominal operating point, however fSW varies across the entire operating range.

View Design

STEVAL-ILL007V1: 1 to 3 LEDs @ 0.35, 0.7, or 1A

Manufacturer: STMicroelectronics

The evaluation board is designed to display the full functionality of L5973D as a LED driver to drive one to three 1W, 3W as well as 5W LEDs at 12Vac input. The components selected for the demo board are optimized for 5W LED driver application.

View Design

LM3402EVAL: 350mA @ Vin Max, 6 ~ 42V in

Manufacturer: Texas Instruments

The LM3402 circuit and BOM have been designed to provide a constant forward current of 350 mA to a single LED with a forward voltage of approximately 3.5V. (Typical of white, blue, and green LEDs using InGaN technology.)

View Design

LM3402HVEVAL: 350mA @ Vin Max, 6 ~ 75V in

Manufacturer: Texas Instruments

The LM3402HV circuit and BOM have been designed to provide a constant forward current of 350 mA to a single LED with a forward voltage of approximately 3.5V.

Ripple current will not exceed 70 mA peak-to-peak. Switching frequency for the demo board is 250 kHz ±10% over the input voltage range of 6V to 75V.

It can maintain regulated current through any number of LEDs as l…

View Design
147 Results - Page 1/15 |< < 1 2 3 4 5 > >|