World's Largest Selection of Electronic Components Available for Immediate Shipment!®

• Efficiency: up to 89% at 72 VIN, 12 V 
• Ultra-wide input range: 16 V to 160 V 
• Quarter-brick package: 61.21 mm x 39.62 mm x 13 mm 
• Operating temperature range: -40°C to +100°C

• Designed to facilitate compliance to UL1449 
• 3rd Edition for SPD products 
• High peak surge current rating up to 10 kA 
• Low leakage

RAFI's RAMO series mono constructed industrial controls provide highly economical and easy-to-install alternatives to traditional 22 mm and 30 mm product. Due to the M12 connector, they need no extra housings or special gaskets to be fully sealed both above and below the mounting panel.

The foil on ceramic construction of the WFC series enables high power capability, lower TCR, and reaches lower resistance values than is available with comparable SMD thick-film current sense resistor technology.

CP10.241-R2-C1 is a compact, reliable 24V, 10A DIN rail power supply with conformally coated PCBs, allowing operation in tough conditions (high humidity, dust). A built-in decoupling MOSFET allows setup of a 1+1 or n+1 redundancy without a redundancy module, resulting in both space & cost savings.

• High rated currents up to 7.05 A 
• Exceptionally high saturation currents of up to 16.1 A
• Very low RDC values as low as 0.018 Ω 
• High temperature range of up to 150 °C

Texas Instruments' DRV8251 & DRV8251A are integrated motor drivers with an N-channel H-bridge, a charge pump, current regulation, protection circuitry, and current sense feedback (DRV8251A). The charge pump improves efficiency by supporting N-channel MOSFET half-bridges and 100% duty-cycle driving.

MPD's line of standard 12V cable sets includes P/N ZA5077. It has a 3A fuse, red led, 6' cord, R/A DC plug on one side and a 12V auto plug. They are made of the finest materials having undergone extreme durability testing including dragging and crushing.

Riedon's FB and CFB fuse holders are designed for Class T, fast-acting fuses. These rugged components are available with terminations suitable for ring/spade terminals up to #4 (FB) or bare wire up to #6 - 250 gauge (CFB). 

Hammond's 1551USB miniature plastic USB enclosures are ideally suited for dongles and/or mounting small printed circuit boards with USB connectors. Molded in ABS plastic (material has a UL94-HB rating). They are available in three lengths and five colors.

• Test and measurement equipment
• Medical laboratory equipment
• Communications equipment
• Industrial automation controls

Vicor's thermally-adept ChiP-based power components enable customers to achieve cost-effective power designs delivering high performance. The fixed ratio BCM6123 offers low noise, fast transient response, and industry-leading efficiency (up to 98%) and power density (up to 2,867 W/in3 ).

MORNSUN compact open-frame AC/DC converter LOF series designed to meet 2XMOPP level and features 4000VAC isolation voltage, active PFC, and leakage current as low as 0.1mA, making it an ideal or optimal solution for various applications, especially for the medical and healthcare sector.

• Custom frequencies, programmed from 1.000000 to 26.000000 MHz 
• 60 µA at 3.072 MHz, up to 90% lower than quartz XOs 
• 1.5 x 0.8 mm package, ideal for mobile and IoT devices 
• Available with short lead times

XP Power’s low cost VR & SVR series of switching regulators offer high efficiency replacements for linear regulators 

• 0.5A, 1A, 2A regulated non-isolated switching regulators 
• Compact through hole and SMD packages
• 96% efficiency requiring no heatsink or additional components

THA and THAS thinpack capacitors offer the highest energy density available in low-profile aluminum electrolytic technology. They are ideal for the lowest-profile circuits, requiring high-capacitance bulk storage, and filtering.

• Ultra-Low Power Consumption - well under 100nA !
• Popular alternative to both Hall effect sensors and Reed switches 
• High sensitivity, Miniature size, Solid State, Analog (Linear) or Digital output
• Short Lead Times!

These solutions combine ADI's precision amplifiers, voltage references, ADCs, DACs, circuit protection and isolation products, allowing system designers to build with confidence a solution that optimizes for their precision and speed requirements.

• Diagnostics monitor with LED indication of utilization 
• 150% extra-power for 5 s/min for short-term overload 
• Push-in terminals with separate ground terminal 
• High-efficiency up to 95%

KYOCERA AVX Accu-P SMD capacitors are designed for soldering to printed circuit boards or other substrates. The construction of the components is such that they will withstand the time/temperature profiles used in both wave and reflow soldering methods.