ReferenceDesignLibrary

Refine Search

Eval Board Purpose Component Count + Extras Features Data Rate Design Author
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (10)

10 Results - Page 1/1

SN65LVPE502CPEVM: USB 3.0 Redriver EVM

Manufacturer: Texas Instruments

The SN65LVPE502CP is a dual channel, single lane USB 3.0 re-driver and signal conditioner supporting data rates of 5.0 Gbps. The device complies with USB 3.0 spec revision 1.0, supporting electrical idle condition and low frequency periodic signals (LFPS) for USB 3.0 power management modes.

View Design

HD3SS6126: USB 3.0 KVM Switch

Manufacturer: Texas Instruments

This user's guide shows a USB 3.0 KVM switch application example of the HD3SS6126 device and provides recommendations for high-speed digital signal PCB design.

View Design

TUSB1002AEVM: USB 3.1, 10 Gbps, Dual Channel Linear Redriver

Manufacturer: Texas Instruments

The TUSB1002A is a dual channel, USB 3.1 SuperSpeed Plus re-driver and signal conditioner supporting data rates of 10.0Gbps. The device complies with USB 3.1 spec revision 1.0, supporting electrical idle condition and low frequency periodic signals (LFPS) for USB 3.1 power management modes. The device offers programmable equalization that extends the interconnect distance between two devices.

View Design

TIPD125: DAC Signal Conditioning, 24-Bit SPI in

Manufacturer: Texas Instruments

This unipolar to bipolar signal conditioning circuit uses an op amp with negative feedback and three resistors in a modified summing amplifier configuration to generate high-voltage bipolar outputs from a generic single supply unipolar digital-to-analog converter (DAC).

View Design

TIPD126: Bridge Sensor Conditioner

Manufacturer: Texas Instruments

This bridge sensor conditioner module delivers a well regulated current output to a ground-referenced load. The first stage uses a mixed-signal programmable gain amplifier (PGA) to provide linearization and temperature compensation to a differential bridge sensor voltage. The second stage converts the PGA output voltage into current and transmits the current over a standard 4 mA to 20 mA current …

View Design

TIPD108: PWM Signal Generator

Manufacturer: Texas Instruments

This circuit utilizes a triangle wave generator and comparator to generate a pulse-width-modulated (PWM) waveform with a duty cycle that is inversely proportional to the input voltage. An op amp and comparator generate a triangular waveform which is passed to the inverting input of a second comparator.

View Design

TUSB564RNQEVM: USB Type-C / VESA DisplayPort™, Alternate Mode, redriving switch

Manufacturer: Texas Instruments

The TUSB564RNQEVM device is a USB Type-C / VESA DisplayPort™, Alternate Mode, re-driving switch which supports data rates up to 10 Gbps for an upstream facing port

View Design

TIDA-00188: IO-Link Sensor Transmitter

Manufacturer: Texas Instruments

This TI Design offers a rapid prototyping platform for IO-Link sensor transmitter. Thanks to its modular design, different sections can be easily cut away to allow fast and simple interfacing of any analog or digital sensor.

View Design

TUSB9261DEMO: USB 3.0 to SATA

Manufacturer: Texas Instruments

The TUSB9261DEMO board is a free-standing reference design that acts as a bridge between a SuperSpeed USB (USB 3.0) bus and a Serial–ATA (SATA) device. The TUSB9261DEMO is used to evaluate system compatibility. It provides a TUSB9261 hardware reference design for connection to a SATA device such as a solid state drive, hard disk drive, DVD drive, or Blu-Ray drive.

View Design

A5191HRTNGEVB: Modem, Highway Addressable Remote Transducer (HART)

Manufacturer: ON Semiconductor

The A5191HRTNGEVB evaluation board includes all external components needed for operating theA5191HRT IC

View Design
10 Results - Page 1/1