EMC, ESD Components Catalog Datasheet by Panasonic Electronic Components

View All Related Products | Download PDF Datasheet
CATALOG
2019
2019.6 industrial.panasonic.com/
EMC Components
ESD Components
Panasonic
– 1 –
EMC Components / ESD Components CONTENTS
All products in this catalog comply with the RoHS Directive.
The RoHS Directive is “the Directive (2011/65/EU) on the Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment “ and its revisions.
Classifi cation Product Item Part No. Page
Safety Precautions (Common precautions for EMC Components and ESD Suppressor) 2
EMC Components
Common mode Noise Filters
EXC X4CZ 3
EXC X4CH 5
EXC X4CE 7
EXC X4CT 9
EXC 14CH 11
EXC 14CG, 14CE 13
EXC 14CT 16
EXC 14CX 18
EXC 16CT 20
EXC 24CH 22
EXC 24CG 24
EXC 24CE, 24CF 26
EXC 34CG, 34CE 28
Common mode Noise Filter Array
EXC 18CG, 18CE 30
EXC 28CH 32
EXC 28CG 34
EXC 28CE 36
Packaging methods, Land pattern and Soldering conditions
for Common mode Noise Filters / Array 38
Common mode Noise Filters with ESD Suppressor EXC 14CS 40
EXC 24CS 42
Common mode Noise Filter Array with ESD Suppressor EXC 18CS 44
Packaging methods and Soldering conditions
for Common mode Noise Filters with ESD Suppressor 46
2 mode Noise Filters EXC 14CP 48
EXC 24CB, 24CP, 24CN 50
Packaging methods, Land pattern and Soldering conditions
for 2 mode Noise Filters 53
Perfomance for Common mode Noise Filters/Common mode Noise Filters with ESD Suppressor/
2 mode Noise Filters
55
Safety precautions for Common mode Noise Filters/Common mode Noise Filters with ESD Suppressor/
2 mode Noise Filters
56
ESD Components
ESD Suppressor EZA EG2A, EG3A 57
EZA EG1N, EG2N 59
ESD Suppressor Array EZA EGCA 61
ESD Suppressor High Withstanding Type EZA EG3W 63
Packaging methods, Soldering conditions and Safety precautions for ESD Suppressor / Array 65
Multilayer Varistor (Automotive Grade) EZJ Z-M / EZJ P-M 66
Multilayer Varistor
(DC voltage lines / High speed signal lines) EZJ Z / EZJ P 77
Multilayer Varistor (DC voltage lines) EZJ S 82
Common specifications Packaging methods and Safety precautions for Multilayer Varistor 84
May. 201906
Panasonic A
– 2 –
Safety Precautions (Common precautions for EMC Components and ESD Suppressor)
When using our products, no matter what sort of equipment they might be used for, be sure to make a written
agreement on the specifications with us in advance. The design and specifications in this catalog are subject
to change without prior notice.
Do not use the products beyond the specifications described in this catalog.
This catalog explains the quality and performance of the products as individual components. Before use, check
and evaluate their operations when installed in your products.
Install the following systems for a failsafe design to ensure safety if these products are to be used in equip ment
where a defect in these products may cause the loss of human life or other significant dam age, such as damage to
vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating
appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment.
Systems equipped with a protection circuit and a protection device
Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a sin gle fault
(1) Precautions for use
These products are designed and manufactured for general and standard use in general elec tron ic equipment
(e.g. AV equipment, home electric appliances, office equipment, information and communication equipment)
These products are not intended for use in the following special conditions. Before using the products,
carefully check the effects on their quality and performance, and determine whether or not they can be used.
1. In liquid, such as water, oil, chemicals, or organic solvent
2. In direct sunlight, outdoors, or in dust
3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
4. Electric Static Discharge (ESD) Environment (except ESD Suppressors)
These components are sensitive to static electricity and can be damaged under static shock (ESD).
Please take measures to avoid any of these environments.
Smaller components are more sensitive to ESD environment.
5. Electromagnetic Environment
Avoid any environment where strong electromagnetic waves exist.
6. In an environment where these products cause dew condensation
7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with
resin or other materials
These products generate Joule heat when energized. Carefully position these products so that their heat will
not affect the other components.
• Carefully position these products so that their temperatures will not exceed the category temperature range due
to the effects of neighboring heat-generating components. Do not mount or place heat-generating components
or inflammables, such as vinyl-coated wires, near these products.
Note that non-cleaning solder, halogen-based highly active flux, or water-soluble flux may deteriorate the
performance or reliability of the products.
• Carefully select a flux cleaning agent for use after soldering. An unsuitable agent may deteriorate the performance
or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave water
residues. Otherwise, the insulation performance may be deteriorated.
(2) Precautions for storage
Do not store these products in the following conditions. Otherwise, their electrical performance and/or
solderability may be deteriorated, and the packaging materials (e.g. taping materials) may be deformed or
deteriorated, resulting in mounting failures.
1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
2. In direct sunlight
<Package markings>
Package markings include the product number, quantity, and country of origin.
In principle, the country of origin should be indicated in English.
Dec. 201601
%% CDDDDDDDIDDD WHHW W Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 3 –
E
1
X
2
C
3
X
4
4
5
C
6
Z
7
2
8
0
9
0
10
X
11 12
Noise Filter Wide band width,
high attenuation
Z
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Pressed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
X
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.65 × 0.50 × 0.30
(L) × (W) × (H)
Code
X
43
12
43
12
E
F
A
B
D
C
Ceramics
Inner Conductor
Electrode
Common mode Noise Filters
Type: EXCX4CZ
Small and thin (L 0.65 mm×W 0.50 mm×H 0.30 mm)
High-common mode attenuation at 2.4GHz, Suitable for noise suppression at Wi-Fi band
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Suppresses noise radiation to Wi-Fi Equipment
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXCX4CZ
(0202)
0.50±0.05 0.65±0.05 0.30±0.05 0.12±0.10 0.40±0.10 0.15±0.10
0.28
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Oct. 201503
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 4 –
(B) Differential Mode(A) Common Mode
ZZ
1
10
100
10000
1000
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Common Mode
Differential Mode
-50
-40
-45
-35
-30
-25
-5
-10
-15
-20
0
100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode
EXCX4CZ200X 20 Ω±30 % 10 100 3.0±30 %
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
EXCX4CZ200X
EXCX4CZ200X
Attenuation Characteristics (Typical)
Oct. 201503
%% / KDDDIDDDIDDD EH‘T W W H % Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 5 –
E
1
X
2
C
3
X
4
4
5
C
6
H
7
3
8
5
9
0
10
X
11 12
Noise Filter High speed
Differential transmission
H
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Pressed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
X
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.65 × 0.50 × 0.30
(L) × (W) × (H)
Code
X
43
12
43
12
Electrode
Inner Conductor
Ceramics Ferrite
A
B
D
C
F
E
Common mode Noise Filters
Type: EXCX4CH
Small and thin (L 0.65 mm×W 0.50 mm×H 0.30 mm)
High common mode attenuation in high-speed differential transmission lines, Cut-off frequency is more than
8.5 GHz, and an infl uence to differential transmission signal quality is little
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Noise suppression of high-speed differential data lines such as USB, LVDS and HDMI
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXCX4CH
(0202)
0.50±0.05 0.65±0.05 0.30±0.05 0.12±0.10 0.40±0.10 0.15±0.10
0.43
Feb. 201600
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 6 –
(B) Differential Mode(A) Common Mode
ZZ
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuations (dB)
-20
-5
-10
-15
0
1 10 100 1000 10000
EXCX4CH350
EXCX4CH120
Frequency (MHz)
Attenuations (dB)
-30
-25
-20
-5
-10
-15
0
1 10 100 1000 10000
EXCX4CH350
EXCX4CH120
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Ratings
Measurement Circuit
EXCX4CH350X
EXCX4CH120X
Insertion Loss (Typical)
Common mode Attenuation Characteristics (Typical)
Impedance Characteristics (Typical)
Category Temperature Range –40 °C to +85 °C
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode
EXCX4CH120X 12 Ω±5 Ω5 100 2.0
EXCX4CH350X 35 Ω±30 % 5 100 2.7
Feb. 201600
%% \_IU_IU_I CDDDDDDDIDDD WHHW W Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 7 –
E
1
X
2
C
3
X
4
4
5
C
6
E
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
E
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Pressed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.65 × 0.50 × 0.30
(L) × (W) × (H)
Code
X
43
12
43
12
E
F
A
B
D
C
Ferrite
Inner Conductor
Electrode
Common mode Noise Filters
Type: EXCX4CE
Small and thin (L 0.65 mm×W 0.50 mm×H 0.30 mm)
Noise suppression of high-speed differential transmission lines with little in uence of waveform rounding on
signal transmission
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Noise suppression of high-speed differential data lines such as MIPI, USB and LVDS
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXCX4CE
(0202)
0.50±0.05 0.65±0.05 0.30±0.05 0.12±0.10 0.40±0.10 0.15±0.10
0.56
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Oct. 201503
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 8 –
(B) Differential Mode(A) Common Mode
ZZ
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXCX4CE600U 60 Ω±20 % 18 Ω max. 5 100 2.4±30 %
EXCX4CE900U 90 Ω±20 % 20 Ω max. 5 100 3.0±30 %
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
EXCX4CE600U EXCX4CE900U
Oct. 201503
%% \_IU_IU_I CDDDDDDDIDDD WHHW W Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 9 –
E
1
X
2
C
3
X
4
4
5
C
6
T
7
9
8
0
9
0
10
X
11 12
Noise Filter High attenuation type
T
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Pressed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
X
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.65 × 0.50 × 0.30
(L) × (W) × (H)
Code
X
43
12
43
12
A
B
D
C
F
E
Electrode
Inner Conductor
Ceramics Ferrite
Common mode Noise Filters
Type: EXCX4CT
Small and thin (L 0.65 mm×W 0.50 mm×H 0.30 mm)
High attenuation at common-mode for noise suppression of harmonic signal components and cellular frequency
Cut-off frequency is more than 3 GHz, the insertion loss is low in differential transmission line
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Noise suppression of high-speed differential data lines such as MIPI, USB and LVDS
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXCX4CT
(0202)
0.50±0.05 0.65±0.05 0.30±0.05 0.12±0.10 0.40±0.10 0.15±0.10
0.43
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Sep. 201500
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 10 –
(B) Differential Mode(A) Common Mode
ZZ
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–20
–10
–15
0
–5
1 10 100 1000 10000
EXCX4CT900X
EXCX4CT650X
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–40
–20
–30
0
–10
1 10 100 1000 10000
EXCX4CT900X
EXCX4CT650X
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Ratings
Impedance Characteristics (Typical)
Insertion Loss (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)
Common Mode
EXCX4CT650X 65 Ω±20 % 10 100 2.7 Ω±30 %
EXCX4CT900X 90 Ω±20 % 10 100 3.0 Ω±30 %
Category Temperature Range –40 °C to +85 °C
Measurement Circuit
EXCX4CT650X EXCX4CT900X
Common mode Attenuation Characteristics (Typical)
Sep. 201500
%% / KDDDIDDDIDDD EH‘T W W H % Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 11 –
E
1
X
2
C
3
1
4
4
5
C
6
H
7
3
8
5
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
H
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.85 × 0.65 × 0.45
(L) × (W) × (H)
Code
1
43
12
43
12
Electrode
Inner Conductor
Ceramics Ferrite
A
B
D
C
F
E
Common mode Noise Filters
Type: EXC14CH
Small and thin (L 0.85 mm×W 0.65 mm×H 0.45 mm)
High common mode attenuation in high-speed differential transmission lines, Cut-off frequency is more than
8.5 GHz, and an infl uence to differential transmission signal quality is little
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Noise suppression of high-speed differential data lines such as USB, LVDS and HDMI
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC14CH
(0302)
0.65±0.05 0.85±0.05 0.45±0.05 0.10 min. 0.50±0.10 0.27±0.10
1.0
Sep. 201500
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 12 –
(B) Differential Mode(A) Common Mode
ZZ
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuations (dB)
-20
-5
-10
-15
0
1 10 100 1000 10000
EXC14CH120
EXC14CH350
Frequency (MHz)
Attenuation (dB)
-30
-25
-20
-5
-10
-15
0
1 10 100 1000 10000
EXC14CH120
EXC14CH350
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Ratings
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC14CH120U 12 Ω±25 % 10 Ω max. 5 100 1.0
EXC14CH350U 35 Ω±30 % 15 Ω max. 5 100 1.5
Category Temperature Range –40 °C to +85 °C
Measurement Circuit
EXC14CH350U
EXC14CH120U
Insertion Loss (Typical)
Common mode Attenuation Characteristics (Typical)
Impedance Characteristics (Typical)
Sep. 201500
\_‘l—‘ KDDDDDDDIDDD Panasonic fie‘ew a
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 13 –
E
1
X
2
C
3
1
4
4
5
C
6
E
7
9
8
0
9
0
10
U
11 12
Noise Filter
High-Q type
G
High speed
Differential transmission
E
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.85 × 0.65 × 0.45
(L) × (W) × (H)
Code
1
E
F
A
B
D
C
Ferrite
Inner Conductor
Electrode
43
12
43
12
Common mode Noise Filters
Type: EXC14CG
EXC14CE
Small and thin (L 0.85 mm×W 0.65 mm×H 0.45 mm)
Noise suppression of high-speed differential transmission lines with little infl uence of waveform rounding on
signal transmission
Low DC resistance and low insertion loss
High-Q value and high impedance of GHz zone : EXC14CG type
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Noise suppression of high-speed differential data lines such as USB, LVDS and MHL
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Features
Recommended Applications
Explanation of Part Numbers
Construction Dimensions in mm (not to scale)
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC14CG/CE
(0302)
0.65±0.05 0.85±0.05 0.45±0.05 0.10 min. 0.50±0.10 0.27±0.10
1.4
Circuit Confi guration(No Polarity)
Jun. 201504
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 14 –
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
1
10
100
1000
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Differential Mode
Common Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
(B) Differential Mode(A) Common Mode
ZZ
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC14CG120U 12 Ω±30 % 10 Ω max. 5 130 2.0
EXC14CG350U 35 Ω±30 % 15 Ω max. 5 100 2.0
EXC14CG430U 43 Ω±25 % 15 Ω max. 5 100 2.7
EXC14CE650U 65 Ω±20 % 20 Ω max. 5 130 2.5
EXC14CE900U 90 Ω±20 % 20 Ω max. 5 130 2.5
EXC14CE121U 120 Ω±20 % 20 Ω max. 5 100 3.8
Category Temperature Range –40 °C to +85 °C
Measurement Circuit
EXC14CG430U
EXC14CG120U
EXC14CE900U EXC14CE121U
EXC14CE650U
EXC14CG350U
Jun. 201504
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 15 –
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Frequency (MHz)
Attenuation (dB)
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Common Mode
Differential Mode
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Frequency (MHz)
Attenuation (dB)
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Common Mode
Differential Mode
Attenuation Characteristics (Typical)
EXC14CG430U
EXC14CG120U
EXC14CE900U EXC14CE121U
EXC14CE650U
EXC14CG350U
Jun. 201504
%% {$5 A/ CDDDIDDDIDDD % flé Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 16 –
E
1
X
2
C
3
1
4
4
5
C
6
T
7
9
8
0
9
0
10
U
11 12
Noise Filter High attenuation type
T
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.85 × 0.65 × 0.45
(L) × (W) × (H)
Code
1
E
F
A
B
D
C
Ferrite
Inner Conductor
Electrode
43
12
43
12
Common mode Noise Filters
Type: EXC14CT
Small and thin (L 0.85 mm×W 0.65 mm×H 0.45 mm)
High attenuation at common-mode for noise suppression of harmonic signal components and cellular
frequency
High cut-off frequency and capability of coping with high-speed signals (USB and HDMI)
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Noise suppression of high-speed differential data lines such as MIPI, USB and LVDS
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC14CT
(0302)
0.65±0.05 0.85±0.05 0.45±0.05 0.10 min. 0.50±0.10 0.27±0.10
1.0
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Mar. 201500
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 17 –
(B) Differential Mode(A) Common Mode
ZZ
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–35
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
–35
–30
–20
–25
–10
–15
0
–5
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Ratings
Impedance Characteristics (Typical)
Attenuation Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC14CT500U 50 Ω±25 % 17 Ω max. 5 100 2.3 Ω±30 %
EXC14CT900U 90 Ω±20 % 20 Ω max. 5 100 3.3 Ω±30 %
Category Temperature Range –40 °C to +85 °C
Measurement Circuit
EXC14CT900U
EXC14CT900U
EXC14CT500U
EXC14CT500U
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Mar. 201500
%% % CDDDDDDDIDDD WHHW W Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 18 –
E
1
X
2
C
3
1
4
4
5
C
6
X
7
9
8
0
9
0
10
U
11 12
Noise Filter Both Common mode
and Differential mode
noise suppression type
X
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.85 × 0.65 × 0.45
(L) × (W) × (H)
Code
1
43
12
43
12
E
F
A
B
D
C
Ferrite
Inner Conductor
Electrode
Common mode Noise Filters
Type: EXC14CX
Small and thin (L 0.85 mm×W 0.65 mm×H 0.45 mm)
Effective noise suppression of smartphones by eliminating common mode noises and removing differential
signal components
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
Noise suppression of high-speed differential data lines such as MIPI, USB and LVDS
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC14CX
(0302)
0.65±0.05 0.85±0.05 0.45±0.05 0.10 min. 0.50±0.10 0.27±0.10
1.4
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Sep. 201502
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 19 –
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Differential Mode
Common Mode
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
-35
-30
-25
-5
-10
-15
-20
0
1 10 100 1000 10000
Common Mode
Differential Mode
Frequency (MHz)
Attenuation (dB)
-35
-30
-25
-5
-10
-15
-20
0
1 10 100 1000 10000
Common Mode
Differential Mode
(B) Differential Mode(A) Common Mode
ZZ
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC14CX280U 28 Ω±25 % 25 Ω max. 5 100 3.0
EXC14CX400U 40 Ω±25 % 30 Ω max. 5 100 4.0
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
EXC14CX400U
EXC14CX280U
EXC14CX400U
EXC14CX280U
Attenuation Characteristics (Typical)
Sep. 201502
Panasonic KDDDDDDDIDDD EHHWH %% \_l \_IU_IU_I m | E33 | m m >
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 20 –
E
1
X
2
C
3
1
4
6
5
C
6
T
7
3
8
5
9
0
10
U
11 12
Noise Filter High attenuation type
T
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
6 Terminals
Dimensions(mm)
0.90 × 0.68 × 0.40
(L) × (W) × (H)
Code
1
Electrode
Inner Conductor
Ceramics Ferrite
A
B
D
C
F
EE
54
23
6
1
6
1
4
3
5
2
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Common mode Noise Filters
Type: EXC16CT
Corresponding to new high-speed differential interface (MIPI C-PHY)
Corresponding to 3-line transmission, transmission rate up to 2.5 Gsps
Unique plating fi ne coil process and ceramic multilayer process enable compact size
(L 0.9.0 mm×W 0.68 mm×H 0.40 mm)
around 40% reduction of mounting area (comparing with MIPI D-PHY)
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
High resolution camera and display equipped mobile devices (Smartphones, Tablet PCs and wearable)
Noise suppression of high-speed differential data lines such as MIPI C-PHY
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCD EF
EXC16CT
(0403)
0.68±0.05 0.90±0.05 0.40±0.05
0.125±0.075
0.35±0.05
0.165±0.065
1.1
Features
Recommended Applications
Explanation of Part Numbers
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)Construction
May. 201700
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 21 –
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
10 100 1000 10000
EXC16CT350U
EXC16CT250U
Frequency (MHz)
Attenuation (dB)
–35
–20
–15
–25
–30
0
–10
–5
10 100 1000 10000
EXC16CT350U
EXC16CT250U
Frequency (MHz)
Attenuation (dB)
–20
–10
–15
0
–5
10 100 1000 10000
AB
BC
CA
Common Mode
Z
A
B
C
A
B
C
A
B
C
Frequency (MHz)
Attenuation (dB)
–20
–10
–15
0
–5
10 100 1000 10000
AB
BC
CA
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω) max.
Common Mode
EXC16CT250U 25 Ω±25 % 5 100 3.0
EXC16CT350U 35 Ω±25 % 5 100 4.0
Category Temperature Range –40 °C to +85 °C
Measurement Circuit
Measurement Circuit
EXC16CT250U EXC16CT350U
AB BC AC
Measurement Circuit
Common mode Impedance Characteristics (Typical)
Common mode Attenuation Characteristics (Typical)
Differential Insertion Loss (Typical)
May. 201700
l—‘ l—‘ @i‘ A / CDDDIDDDIDDD Q5 [1% Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 22 –
E
1
X
2
C
3
2
4
4
5
C
6
H
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
(for Gbps)
H
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Code
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
1.25 × 1.00 × 0.50
(L) × (W) × (H)
Code
2
Ferrite
Inner Conductor Electrode
E
F
A
B
D
C
43
12
43
12
Common mode Noise Filters
Type: EXC24CH
Small and thin type, built-in fi lter circuit (L 1.25 mm×W 1.00 mm×H 0.50 mm)
Suppression of high frequency noise with little influence of waveform rounding on signal transmission,
achieved by setting high cut-off frequency between 6 and 10 GHz
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD),
Communications equipment (Mobile phones, Smartphones)
Noise suppression of high-speed differential data lines such as USB 3.0, HDMI and Display Port
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC24CH
(0504)
1.25±0.15 1.00±0.15 0.50±0.10 0.20±0.15 0.55±0.10 0.30±0.10
3
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Mar. 201503
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 23 –
(B) Differential Mode(A) Common Mode
ZZ
EXC24CH500U
EXC24CH900U
1 10 100 1000 10000
Frequency (MHz)
0
Attenuation (dB)
-4
-2
-6
-8
-10
Common Mode
EXC24CH500U
EXC24CH900U
EXC24CH900U
EXC24CH500U
Differential Mode
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
1000
100
10
1
Ratings
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
Part Number Impedance (Ω) at 100 MHz
Cutoff Frequency
(GHz)
Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC24CH500U 50 Ω±25 % 13 Ω max. 10 Typ. 5 160 1.5
EXC24CH900U 90 Ω±20 % 15 Ω max. 6 Typ. 5 130 2.5
Impedance Characteristics (Typical)
Insertion Loss (Typical)
Mar. 201503
l—‘l—‘ KDDDIDDDIDDD fit D % Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 24 –
E
1
X
2
C
3
2
4
4
5
C
6
G
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
(for Gbps)
G
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
1.25 × 1.00 × 0.50
(L) × (W) × (H)
Code
2
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
Electrode
Inner Conductor
Ceramics Ferrite
A
B
D
C
F
E
43
12
43
12
Common mode Noise Filters
Type: EXC24CG
Elimination of radiation noises from high-speed differential transmissions
Prevention of reflection of transmission signals and noise radiation by controlling TDR characteristic
impedance as 100 Ω
Satisfaction of eye pattern standards of HDMI waveforms with capability to improve waveform fl uctuations of
skew and overshoot
Simple multilayer structure, excellent mass productivity and high reliability
Small and thin (L 1.25 mm×W 1.00 mm×H 0.50 mm)
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD),
Communications equipment (Mobile phones, Smartphones)
Noise suppression of high-speed differential data lines such as HDMI, SATA and LAN
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC24CG
(0504) 1.25±0.15 1.00±0.15 0.50±0.10 0.20±0.15 0.55±0.10 0.30±0.10
3
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Jan. 201605
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 25 –
(B) Differential Mode(A) Common Mode
ZZ
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
10000
1000
100
10
1
Common Mode
Differential Mode
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
10000
1000
100
10
1
Common Mode
Differential Mode
1 10 100 1000 10000
Frequency (MHz)
10000
Impedance (Ω)
1000
100
10
1
Common Mode
Differential Mode
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC24CG240U 24 Ω±25 % 15 Ω max. 5 160 1.5
EXC24CG360U 36 Ω±25 % 15 Ω max. 5 130 1.7
EXC24CG900U 90 Ω±25 % 20 Ω max. 5 100 3.0
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
EXC24CG240U
EXC24CG900U
EXC24CG360U
Jan. 201605
%% Q”? A/ CDDDIDDDIDDD ai EH Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 26 –
Ferrite
Inner Conductor Electrode
E
1
X
2
C
3
2
4
4
5
C
6
E
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
(for Mbps)
E
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
High speed
Differential transmission
(for Mbps) High-Q type
F
C
Number of
Terminals
4 Terminals
Dimensions(mm)
1.25 × 1.00 × 0.50
(L) × (W) × (H)
Code
2
PackingCode
UEmbossed Carrier Taping
4 mm pitch, 5,000 pcs.
E
F
A
B
D
C
43
12
43
12
Common mode Noise Filters
Type: EXC24CE
EXC24CF
Elimination of radiation noises from high-speed differential transmissions
Strong multilayer structure, excellent refl ow resistance and high mounting reliability
Magnetic shield type with no leakage
High-Q impedance : EXC24CF
Small and thin (L 1.25 mm×W 1.00 mm×H 0.50 mm)
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD, Printers),
Communications equipment (Mobile phones, Smartphones)
Noise suppression of high-speed differential data lines such as USB2.0 and LVDS
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC24CE/CF
(0504)
1.25±0.15 1.00±0.15 0.50±0.10 0.20±0.15 0.55±0.10 0.30±0.10
3
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Mar. 201503
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 27 –
(B) Differential Mode(A) Common Mode
ZZ
1
10
100
1000
10000
1 10 100 1000 10000
1
10
100
1000
10000
1 10 100 1000 10000
Frequency (MHz)
Frequency (MHz)
Frequency (MHz)
Impedance (Ω)
Impedance (Ω)Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Common Mode
Differential Mode
Common Mode
Differential Mode
Frequency (MHz)
Impedance (Ω)
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000 10000
1
10
100
1000
1 10 100 1000 10000
Common Mode
Common Mode
Differential Mode
Differential Mode
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC24CE360UP 36 Ω±25 % 20 Ω max. 5 200 1.0
EXC24CE900U 90 Ω±25 % 15 Ω max. 5 160 1.75
EXC24CE121U 120 Ω±25 % 18 Ω max. 5 140 2.2
EXC24CE201U 200 Ω±25 % 20 Ω max. 5 130 2.7
EXC24CF900U 90 Ω±25 % 20 Ω max. 5 130 2.5
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
EXC24CE121U EXC24CE201U
EXC24CF900U
EXC24CE360UP EXC24CE900U
Mar. 201503
l—‘l—‘ % KDDDDDDDIDDD fieefi fl Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 28 –
E
1
X
2
C
3
3
4
4
5
C
6
G
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
(for Mbps)
E
High speed
Differential transmission
(for Gbps)
G
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Code
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
2.00 × 1.25 × 0.50
(L) × (W) × (H)
Code
3
Ferrite
Inner Conductor Electrode
E
F
A
B
D
C
43
12
43
12
Common mode Noise Filters
Type: EXC34CG/CE
Thin type, built-in fi lter circuit (L 2.0 mm×W 1.25 mm×H 0.50 mm)
Noise suppression of high-speed differential transmission lines with little infl uence of waveform rounding on
signal transmission
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD, Printers)
Noise suppression of high-speed differential data lines such as USB2.0, LVDS, HDMI and LAN
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC34C
(0805)
2.00±0.15 1.25±0.15 0.50±0.10 0.30±0.20 0.80±0.10 0.30±0.15
5
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Mar. 201502
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters
– 29 –
(B) Differential Mode(A) Common Mode
ZZ
Frequency (MHz)
Frequency (MHz)
Frequency (MHz)
Impedance (Ω)
Impedance (Ω)
Impedance (Ω)
10
100
Common Mode
Differential Mode
1
10
100
1000
10000
1 10 100 1000 10000
1
1000
1 10 100 1000
10
100
1
1000
1 10 100 1000
Differential Mode
Differential Mode
Common Mode
Common Mode
Frequency (MHz)
Impedance (Ω)
Frequency (MHz)
Impedance (Ω)
1
10
100
1000
1 10 100 1000
1
10
100
1000
1 10 100 1000
Differential Mode
Differential Mode
Common Mode
Common Mode
Ratings
Impedance Characteristics (Typical)
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
Part Number Impedance (Ω) at 100 MHz
Rated Current
(mA DC)
Rated Voltage
(V DC)
Insulation Re sis tance
(MΩ min.)
Withstand Voltage
(V DC)
DC Re sis tance
(Ω)max.
Common Mode
EXC34CE670U 67 Ω±25 % 250 5 10 MΩ125 0.8
EXC34CE900U 90 Ω±25 % 250 5 10 MΩ125 0.8
EXC34CE121U 120 Ω±25 % 200 5 10 MΩ125 1.0
EXC34CE201U 200 Ω±25 % 200 5 10 MΩ125 1.0
EXC34CG900U 90 Ω±25 % 100 5 10 MΩ125 3.0
EXC34CE121U EXC34CE201U
EXC34CG900U
EXC34CE670U EXC34CE900U
Mar. 201502
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters Array
– 30 –
E
1
X
2
C
3
1
4
8
5
C
6
E
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
E
Coupled
type The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
High-Q typeG
C
Number of
Terminals
8 Terminals
Dimensions(mm)
1.6 × 0.8 × 0.4
(L)
×
(W)
×
(H)
Code
1
Ferrite
Inner Conductor Electrode
65
34
87
12
87
12
65
34
A
C
B
F
D
E
Common mode Noise Filter Array
Type: EXC18CG
EXC18CE
Small and thin type, two built-in fi lter circuit (L 1.6 mm×W 0.8 mm×H 0.4 mm)
Noise suppression of high-speed differential transmission lines with little in uence of waveform rounding on
signal transmission
Low DC resistance and low insertion loss
High-Q value and high impedance of GHz zone : EXC18CG type
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD, Printers)
Noise suppression of high-speed differential data lines such as USB2.0, LVDS, HDMI and LAN
The pin numbers shown here are for reference purposes only. Confirm the actual
pin number arrangement with the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC18CG/CE
(0603)
0.8±0.1 1.6±0.1 0.4±0.1 0.2±0.1 0.4±0.1 0.2±0.1
2.6
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Mar. 201503
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters Array
– 31 –
1
10
100
1000
1 10 100 1000 10000
1
10
100
1000
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)Impedance (Ω)
Common Mode
Differential Mode
Common Mode
Differential Mode
Frequency (MHz)
(B) Differential Mode(A) Common Mode
ZZ
1
10
100
1000
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Common Mode
Common Mode
Differential Mode
1
10
100
1000
1 10 100 1000 10000
Differential Mode
Frequency (MHz)
Impedance (Ω)
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC18CG430U 43 Ω±25 % 15 Ω max. 5 100 2.7
EXC18CE650U 65 Ω±20 % 18 Ω max. 5 140 1.8
EXC18CE900U 90 Ω±20 % 20 Ω max. 5 130 2.0
EXC18CE201U 200 Ω±20 % 22 Ω max. 5 100 3.5
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
EXC18CE201U
EXC18CE650U
EXC18CG430U
Measurement Circuit
EXC18CE900U
Mar. 201503
CDDDIDD IDES Jeeflfl %%
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array
– 32 –
E
1
X
2
C
3
2
4
8
5
C
6
H
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
(for Gbps)
H
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Code
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
8 Terminals
Dimensions(mm)
2.0 × 1.0 × 0.5
(L)
×
(W)
×
(H)
Code
2
Ferrite
Inner Conductor Electrode
A
C
B
F
D
E
65
34
87
12
87
12
65
34
Common mode Noise Filter Array
Type: EXC28CH
Small and thin type, two built-in fi lter circuit (L 2.0 mm×W 1.0 mm×H 0.5 mm)
Suppression of high frequency noise with little influence of waveform rounding on signal transmission,
achieved by setting high cut-off frequency between 6 and 10 GHz
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD, Printers)
Noise suppression of high-speed differential data lines such as USB3.0, LVDS, HDMI and LAN
The pin numbers shown here are for reference purposes only. Confirm the actual
pin number arrangement with the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC28CH
(0804)
1.00±0.15 2.0±0.2 0.5±0.1 0.20±0.15 0.5±0.1 0.25±0.10
5
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Mar. 201503
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array
– 33 –
(B) Differential Mode(A) Common Mode
ZZ
Common Mode
EXC28CH500U
EXC28CH900U
EXC28CH900U
EXC28CH500U
Differential Mode
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
1000
100
10
1
EXC28CH500U
EXC28CH900U
1 10 100 1000 10000
Frequency (MHz)
0
Attenuation (dB)
-4
-2
-6
-8
-10
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz
Cutoff Frequency
(GHz)
Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC28CH500U 50 Ω±25 % 13 Ω max. 10 Typ. 5 160 1.5
EXC28CH900U 90 Ω±20 % 15 Ω max. 6 Typ. 5 130 2.5
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
Insertion Loss (Typical)
Mar. 201503
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array
– 34 –
E
1
X
2
C
3
2
4
8
5
C
6
G
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
(for Gbps)
G
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
8 Terminals
Dimensions(mm)
2.0 × 1.0 × 0.5
(L)
×
(W)
×
(H)
Code
2
Packing
Code
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
U
Ferrite
Inner Conductor Electrode
A
C
B
F
D
E
65
34
87
12
87
12
65
34
Common mode Noise Filter Array
Type: EXC28CG
Small and thin type, two built-in fi lter circuit (L 2.0 mm×W 1.0 mm×H 0.5 mm)
Prevention of weakening of transmission signals by controlling singal pass band as 3 GHz or above
Prevention of reflection of transmission signals and noise radiation by controlling TDR characteristic
impedance as 100 Ω
Satisfaction of eye pattern standards of HDMI waveforms with capability to improve waveform fl uctuations of
Jitter and phase shift etc
Elimination of radiation noises from high-speed differential transmissions
Magnetic shield type with no leakage
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD),
Communications equipment (Mobile phones, Smartphones)
Noise suppression of high-speed differential data lines such as HDMI, SATA and LAN
The pin numbers shown here are for reference purposes only. Confirm the actual
pin number arrangement with the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC28CG
(0804) 1.00±0.15 2.0±0.2 0.5±0.1 0.20±0.15 0.5±0.1 0.25±0.10
5
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Mar. 201503
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array
– 35 –
(B) Differential Mode(A) Common Mode
ZZ
1 10 100 1000 10000
Frequency (MHz)
10000
Impedance (Ω)
1000
100
10
1
Common Mode
Differential Mode
1 10 100 1000 10000
Frequency (MHz)
10000
Impedance (Ω)
1000
100
10
1
Common Mode
Differential Mode
Ratings
Impedance Characteristics (Typical)
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC28CG240U 24 Ω ±25 % 15 Ω max. 5 160 1.5
EXC28CG900U 90 Ω ±25 % 17 Ω max. 5 130 3.0
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
EXC28CG900U
EXC28CG240U
Mar. 201503
% $$ CDDDIDDDIDDD fieefifi \\ — @ Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array
– 36 –
E
1
X
2
C
3
2
4
8
5
C
6
E
7
9
8
0
9
0
10
U
11 12
Noise Filter High speed
Differential transmission
(for Mbps)
E
Coupled
type The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
8 Terminals
Dimensions(mm)
2.0 × 1.0 × 0.5
(L)
×
(W)
×
(H)
Code
2
Packing
Code
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
U
Ferrite
Inner Conductor Electrode
A
C
B
F
D
E
65
34
87
12
87
12
65
34
Common mode Noise Filter Array
Type: EXC28CE
Small and thin type, two built-in fi lter circuit (L 2.0 mm×W 1.0 mm×H 0.5 mm)
Elimination of radiation noises from high-speed differential transmissions
Magnetic shield type with no leakage
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD, Printers),
Communications equipment (Mobile phones, Smartphones)
Noise suppression of high-speed differential data lines such as USB2.0 and LVDS
The pin numbers shown here are for reference purposes only. Confirm the actual
pin number arrangement with the exchanged specification documents.
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC28CE
(0804)
1.00±0.15
2.0±0.2 0.5±0.1
0.20±0.15
0.5±0.1
0.25±0.10
5
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Sep. 201504
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array
– 37 –
Common Mode
Differential Mode
1
10
100
1000
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
(B) Differential Mode(A) Common Mode
ZZ
Common Mode
Differential Mode
Common Mode
Differential Mode
1
10
100
1000
1 10 100 1000 10000
1
10
100
1000
1 10 100 1000 10000
Frequency (MHz)
Frequency (MHz)
Impedance (Ω) Impedance (Ω)
Ratings
Impedance Characteristics (Typical)
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Measurement Circuit
EXC28CE900U EXC28CE121U
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω) max.
Common Mode Differential Mode
EXC28CE900U 90 Ω±25 % 15 Ω max. 5 160 1.5
EXC28CE121U 120 Ω±25 % 18 Ω max. 5 140 2.0
EXC28CE201U 200 Ω±25 % 20 Ω max. 5 130 2.5
EXC28CE201U
Sep. 201504
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters / Array
– 38 –
E
T
W
fD
fC
fA
fB
B
F
W
E
P1 P2 fD0
P0
A
Tape running direction
TChip component
Sprocket hole
Compartment
t1
t2
D0
P1P2
A
B
FE
W
f
P0
Chip component
Sprocket hole
Compartment
Tape running
direction
t1
t2P1P2P0
A
B
FE
W
fD0
Chip component
Sprocket hole Compartment
Tape running direction
Packaging Methods (Taping)
Standard Quantity
Packaging Methods (Taping)
Pressed Carrier Taping
EXC18C, 24C, 28C, 34C
Embossed Carrier Taping
Embossed Carrier Taping Taping Reel
Taping Reel
Pressed Carrier Taping
Part Number A B W F E P1P2P0fD0T
EXCX4C
0.60±0.10 0.80±0.10
8.0±0.2
3.50±0.05 1.75±0.10
2.0±0.1 2.0±0.1 4.0±0.1 1.5+0.1 0.35 typ.
0
(mm)
Embossed Carrier Taping (mm)
(mm)
Standard Reel Dimensions
EXCX4C EXC14C, 16C
Part Number fAfBfCfDE W T
EXCX4C
180.0±3.0 60.0±1.0
13.0±0.2
21.0±0.8 2.0±0.5 9.0±0.3
11.4±1.0
EXC14C
EXC16C
EXC18C
EXC24C
EXC28C
EXC34C
13.0±0.5 11.4±1.5
0
0
Part Number A B W F E P1P2P0fD0t1t2
EXC14C
0.75±0.10 0.95±0.10
8.0±0.2
3.50±0.05 1.75±0.10
2.0±0.1 2.0±0.1 4.0±0.1 1.5+0.1
0.25±0.05 0.85±0.15
EXC16C
0.77±0.10 0.99±0.10 0.80±0.15
EXC18C
1.00±0.10 1.80±0.10
8.0±0.2 3.5±0.1
1.75±0.10
4.0±0.1 2.0±0.1 4.0±0.1 1.5+0.1
0.25±0.05
0.80±0.05
EXC24C
1.20±0.15 1.45±0.15
0.90±0.15
EXC28C
2.25±0.15
EXC34C
1.50±0.20 2.30±0.20
Part Number Size (inch) Type Kind of Taping Pitch (P1) Quantity
EXCX4C 0202
Single
Pressed Carrier Taping 2 mm 10,000 pcs./reel
EXC14C 0302
Embossed Carrier Taping
2 mm 10,000 pcs./reel
EXC16C 0403
EXC24C 0504
4 mm 5,000 pcs./reel
EXC34C 0805
EXC18C 0603 Array
EXC28C 0804
Dec. 201807
Panasonic — xx “H f—fi V“ ,II ,III ,IIII *II *III ifIIII
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters / Array
– 39 –
Preheating
Peak
Heating
Temperature
Time
A
DCD
EFE
B
A
DCD
EFE
B
FE
A
DCD
EF
B
Recommended Land Pattern Design
Recommended soldering conditions for refl ow
·
Refl ow soldering shall be performed a maximum of two times.
· Please contact us for additional information when used in
conditions other than those specifi ed.
· Please measure the temperature of the terminals and study
every kind of solder and printed circuit board for solderability
be fore ac tu al use.
Recommended Soldering Conditions
<Repair with hand soldering>
Preheat with a blast of hot air or similar method. Use a soldering iron with a tip temperature of 350 °C or less. Solder each electrode for 3 seconds or less.
Never touch this product with the tip of a soldering iron.
Recommendations and precautions are described below
Flow soldering
·
We do not recommend flow soldering, because flow soldering may cause bridges between the electrodes.
For soldering (Example : Sn-37Pb)
For lead-free soldering (Example : Sn/3Ag/0.5Cu)
Temperature Time
Preheating 140 °C to 160 °C 60 s to 120 s
Main heating Above 200 °C 30 s to 40 s
Peak 235 ± 10 °C max. 10 s
Temperature Time
Preheating 150 °C to 170 °C 60 s to 120 s
Main heating Above 230 °C 30 s to 40 s
Peak max. 260 °C max. 10 s
Single
EXCX4C, 14C, 24C, 34C EXC16C
Array
Part
Number
Dimensions (mm)
ABCDEF
EXC18 C 1.4 1.4 0.4 0.5 0.2 0.4
EXC28 C 1.4 1.75 0.4 0.5 0.25 0.5
Part
Number
Dimensions (mm)
ABCDEF
EXCX4C 0.80 to
0.90
0.60 to
0.75
0.20 to
0.30 0.30 0.20 to
0.25
0.20 to
0.25
EXC14C 0.80 to
1.00 0.80 0.30 0.25 to
0.35 0.30 0.20
EXC24 C 1.60 to
2.00 0.95 0.70 0.45 to
0.65 0.35 0.25
EXC34C 2.60 1.20 1.10 0.75 0.40 0.40
EXC16C 0.99 085 0.33 0.33 0.15 0.20
Dec. 201808
Panasonic KDDDIDDDDDCD H a %% 1&3
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters with ESD Suppressor
– 40 –
E
1
X
2
C
3
1
4
4
5
C
6
S
7
9
8
0
9
0
10
H
11 12
Noise Filter Intergrated
ESD Protection
S
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
H
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.85 × 0.65 × 0.45
(L) × (W) × (H)
Code
1
A
B
D
C
F
E
G
Electrode
Inner Conductor
Ceramics Ferrite
65
23
65
2
GND GND114 4
3
Common mode Noise Filters
with ESD Suppressor
Type: EXC14CS
Provides EMI Filtering and ESD Potection (L 0.85 mm×W 0.65 mm×H 0.45 mm)
ESD and noise suppression of high-speed differential transmission lines with little infl uence of
waveform rounding on signal transmission
High Common mode attenuation in the range between 700 MHz and 1 GHz (RF band)
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
ESD and noise suppression of high-speed differential data lines such as MIPI and USB
The pin numbers shown here are for reference
purposes only. Confirm the actual pin number
arrangement with the exchanged specification
documents.
Features
Recommended Applications
Explanation of Part Numbers
Construction Dimensions in mm (not to scale)
Circuit Confi guration(No Polarity)
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEFG
EXC14CS
(0302)
0.67±0.05 0.87±0.05 0.45±0.05 0.15±0.07 0.40±0.05 0.20±0.07 0.20±0.07
0.97
Dec. 201802
Panasonic —
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters with ESD Suppressor
– 41 –
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Time (nsec)
Voltage (V)
0
50
100
150
200
250
300
500
350
400
450
5 0 10152025303540455055605
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
(B) Differential Mode(A) Common Mode
ZZ
0.67
1.17
0.40
0.19
0.20 0.20
0.19
0.47
0.20
Ratings
Category Temperature Range –40 °C to +85 °C
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)
Common Mode Differential Mode
EXC14CS350H 35 Ω±30 % 15 Ω max. 5 100 2.0±30 %
EXC14CS900H 90 Ω±20 % 20 Ω max. 5 100 3.3±30 %
Measurement Circuit
EXC14CS900H
EXC14CS350H
Impedance Characteristics (Typical)
As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
ESD Suppression Characteristics(Typical : IEC61000-4-2, 8 kV contact discharge)
Recommended Land Pattern Design in mm (not to scale)
Dec. 201802
KDDDDDDDDDCD %% \_ILI_ILI_I Panasonic fieefi fl
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters with ESD Suppressor
– 42 –
E
1
X
2
C
3
2
4
4
5
C
6
S
7
9
8
0
9
0
10
U
11 12
Noise Filter Intergrated
ESD Protection
S
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
1.25 × 1.00 × 0.50
(L) × (W) × (H)
Code
2
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
Ceramics
Inner Conductor
Ceramics Ferrite
A
B
D
C
F
E
G
65
23
65
2
GND GND114 4
3
Common mode Noise Filters
with ESD Suppressor
Type: EXC24CS
Provides EMI Filtering and ESD Potection (L 1.25 mm×W 1.00 mm×H 0.50 mm)
ESD and noise suppression of high-speed differential transmission lines with little infl uence of
waveform rounding on signal transmission
High Common mode attenuation in the range between 700 MHz and 1 GHz (RF band)
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
ESD and noise suppression of high-speed differential data lines such as MIPI and USB
The pin numbers shown here are for reference
purposes only. Confirm the actual pin number
arrangement with the exchanged specification
documents.
Explanation of Part Numbers
Construction Dimensions in mm (not to scale)
Features
Recommended Applications
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEFG
EXC24CS
(0504)
1.25±0.15 1.00±0.15 0.50±0.10 0.20±0.15 0.55±0.10 0.30±0.10 0.20±0.10
2.4
Circuit Confi guration (No Polarity)
Nov. 201601
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters with ESD Suppressor
– 43 –
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Time (nsec)
Voltage (V)
0
50
100
150
200
250
300
500
350
400
450
5 0 10152025303540455055605
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
(B) Differential Mode(A) Common Mode
ZZ
1.75
0.75 0.500.50
0.85
0.250.30 0.30
0.40
0.60
0.20
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)max.
Common Mode Differential Mode
EXC24CS350U 35 Ω±30 % 15 Ω max. 5 100 2.0
EXC24CS900U 90 Ω±20 % 20 Ω max. 5 100 3.0
Category Temperature Range –40 °C to +85 °C
Measurement Circuit
EXC24CS900U
EXC24CS350U
Ratings
Impedance Characteristics (Typical)
ESD Suppression Characteristics(Typical : IEC61000-4-2, 8 kV contact discharge)
As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
Recommended Land Pattern Design in mm (not to scale)
Nov. 201601
Panasonic CDDDIDDDDDCD fiéefifi %%
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array with ESD Suppressor
– 44 –
E
1
X
2
C
3
1
4
8
5
C
6
S
7
9
8
0
9
0
10
U
11 12
Noise Filter Intergrated
ESD Protection
S
Coupled
type The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
4 mm pitch, 5,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
8 Terminals
Dimensions(mm)
1.6 × 0.8 × 0.4
(L)
×
(W)
×
(H)
Code
1
Electrode
Inner Conductor
Ceramics
Ferrite
B
A
C
F
E
E
D
87
45
10
16
9
23
10 9
2
GND 1
3
87
4
GND6
5
Common mode Noise Filter Array
with ESD Suppressor
Type: EXC18CS
Provides EMI Filtering and ESD Potection (L 1.6 mm×W 0.8 mm×H 0.4 mm)
ESD and noise suppression of high-speed differential transmission lines with little infl uence of
waveform rounding on signal transmission
High Common mode attenuation in the range between 700 MHz and 1 GHz (RF band)
Strong multilayer/sintered structure, excellent refl ow resistance and high mounting reliability
Lead, halogen and antimony-free
RoHS compliant
Smartphones, Tablet PCs and DSC
ESD and noise suppression of high-speed differential data lines such as MIPI and USB
The pin numbers shown here are for reference purposes only. Confirm the actual
pin number arrangement with the exchanged specification documents.
Explanation of Part Numbers
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC18CS
(0603)
1.6±0.1 0.8±0.1 0.4±0.1 0.4±0.1 0.2±0.1 0.2±0.1
1.9
Nov. 201601
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filter Array with ESD Suppressor
– 45 –
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
Time (nsec)
Voltage (V)
0
50
100
150
200
250
300
500
350
400
450
5 0 10152025303540455055605
Frequency (MHz)
Impedance (Ω)
1
10
100
10000
1000
1 10 100 1000 10000
Common Mode
Differential Mode
(B) Differential Mode(A) Common Mode
ZZ
2.00
1.30
1.42
0.48
0.15
0.200.20
0.35
Ratings
Part Number Impedance (Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω)
Common Mode Differential Mode
EXC18CS350U 35 Ω±30 % 15 Ω max. 5 100 1.8±30 %
EXC18CS900U 90 Ω±20 % 20 Ω max. 5 100 3.0±30 %
Category Temperature Range –40 °C to +85 °C
Measurement Circuit
EXC18CS900U
EXC18CS350U
Impedance Characteristics (Typical)
ESD Suppression Characteristics(Typical : IEC61000-4-2, 8 kV contact discharge)
Recommended Land Pattern Design in mm (not to scale)
As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
Nov. 201601
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters with ESD Suppressor
– 46 –
t1
t2
D0
P1P2
A
B
FE
W
f
P0
Chip component
Sprocket hole
Compartment
Tape running
direction
t1
t2P1P2P0
A
B
FE
W
fD0
Chip component
Sprocket hole Compartment
Tape running direction
E
T
W
fD
fC
fA
fB
Standard Quantity
EXC18CS, EXC24CS
Embossed Carrier Taping Embossed Carrier Taping
Part Number Size (inch) Type Kind of Taping Pitch (P1) Quantity
EXC14CS 0302 Single Embossed Carrier Taping
2 mm 10,000 pcs./reel
EXC24CS 0504 4 mm 5,000 pcs./reel
EXC18CS 0603 Array
Taping Reel
Taping Reel
Part Number fAfBfCfDE W T
EXC14CS
EXC18CS
EXC24CS
180.0±3.0 60.0±1.0 13.0±0.5 21.0±0.8 2.0±0.5 9.0±0.3 11.4±1.5
Embossed Carrier Taping
Part Number A B W F E P1P2P0fD0t1t2
EXC14CS
0.75±0.10 0.95±0.10
8.0±0.2
3.50±0.05 1.75±0.10
2.0±0.1 2.0±0.1 4.0±0.1 1.5+0.1
0.25±0.05 0.85±0.15
EXC18C S
1.00±0.10 1.80±0.10
8.0±0.2 3.5±0.1
1.75±0.10
4.0±0.1 2.0±0.1 4.0±0.1 1.5+0.1
0.25±0.05 0.50±0.05
EXC24C S
1.20±0.15 1.45±0.15 0.90±0.15
0
0
(mm)
(mm)
Standard Reel Dimensions
EXC14CS
Packaging Methods (Taping)
Dec. 201801
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters with ESD Suppressor
– 47 –
Preheating
Peak
Heating
Temperature
Time
Recommended soldering conditions for refl ow
·
Refl ow soldering shall be performed a maximum of two times.
· Please contact us for additional information when used in
conditions other than those specifi ed.
· Please measure the temperature of the terminals and study
every kind of solder and printed circuit board for solderability
be fore ac tu al use.
Recommended Soldering Conditions
<Repair with hand soldering>
Preheat with a blast of hot air or similar method. Use a soldering iron with a tip temperature of 350 °C or less. Solder each electrode for 3 seconds or less.
Never touch this product with the tip of a soldering iron.
Recommendations and precautions are described below
Flow soldering
·
We do not recommend flow soldering, because flow soldering may cause bridges between the electrodes.
For soldering (Example : Sn-37Pb)
For lead-free soldering (Example : Sn/3Ag/0.5Cu)
Temperature Time
Preheating 140 °C to 160 °C 60 s to 120 s
Main heating Above 200 °C 30 s to 40 s
Peak 235 ± 10 °C max. 10 s
Temperature Time
Preheating 150 °C to 170 °C 60 s to 120 s
Main heating Above 230 °C 30 s to 40 s
Peak max. 260 °C max. 10 s
Dec. 201801
Panasonic IDDDDDDDDDID fgfifi 1 W a Li ELI—[M % @2: E] E5
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2 mode Noise Filters
– 48 –
E
1
X
2
C
3
1
4
4
5
C
6
P
7
2
8
2
9
1
10
U
11 12
Noise Filter Low DCR Type
P
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
0.85 × 0.65 × 0.45
(L)
×
(W)
×
(H)
Code
1
E
F
A
B
D
C
Ferrite
Inner Conductor
Electrode
43
12
43
12
2 mode Noise Filters
Type: EXC14CP
Small size and low-profi le : 0302 inch size (L 0.85 mm×W 0.65 mm×H 0.45 mm)
Burst/radiation noise fi ltering for audio circuits
The optimally magnetic-coupled ferrite beads allow for the fi ltering of both common and normal mode noises
The strong multi-layer structure provides high resistance to refl ow soldering heat and a high mounting reliability
Lead, halogen, and antimony free
RoHS compliant
Smart phones, Tablet PCs, DSC and Portable Music Player
Noise suppression of burst noise of Receiver/Microphone and D-class power amplifi er
Explanation of Part Numbers
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC14CP
(0302)
0.65±0.05 0.85±0.05 0.45±0.05
0.10 min.
0.50±0.10 0.27±0.10
1.2
Construction
Circuit Confi guration (No Polarity)
Dimensions in mm (not to scale)
Features
Recommended Applications
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Jul. 201401
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2 mode Noise Filters
– 49 –
0
100
200
300
1 10 100 1000 10000
Impedance (Ω)
Frequency (MHz)
Open Mode
Common Mode
(A)Open Mode (B)Common Mode
ZZ
0
100
200
300
400
500
1 10 100 1000 10000
Impedance (Ω)
Frequency (MHz)
Open Mode
Common Mode
Ratings
Impedance Characteristics (Typical)
Part Number Impedance(Ω) at 100 MHz Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω) max.
Open mode Common mode
EXC14CP121U 120 Ω±30 % 75 Ω±25 % 5300 0.5
EXC14CP221U 220 Ω±30 % 140 Ω±25 % 200 0.7
Category Temperature Range –40 °C to +85 °C
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
EXC14CP221U
EXC14CP121U
Measurement Circuit
Jul. 201401
Panasonic — — — CDDCDDD DEED E#%H\ H % \_l \\ CDDCDDD DEED E#%#\ W % \_l \\
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2 mode Noise Filters
– 50 –
E
1
X
2
C
3
2
4
4
5
C
6
B
7
1
8
0
9
2
10
U
11 12
Noise Filter High Impedance Type
B
Low DCR Type
P
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Packing
Embossed Carrier Taping
2 mm pitch, 5,000 pcs.
Code
U
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
1.25 × 1.00 × 0.50
(L)
×
(W)
×
(H)
Code
2
E
1
X
2
C
3
2
4
4
5
C
6
N
7
6
8
0
9
1
10
X
11 12
Noise Filter High Impedance Type
and Low DCR Type
N
Coupled
type
The first two digits are
significant figure of
impedance value, and the
third one denotes the
number of zeros following
Product Code Type
Characteristics
Size Nominal Impedance Form Suffix
C
Number of
Terminals
4 Terminals
Dimensions(mm)
1.25 × 1.00 × 0.50
(L)
×
(W)
×
(H)
Code
2
Packing
Pressed Carrier Taping
2 mm pitch, 10,000 pcs.
Code
X
2 mode Noise Filters
Type: EXC24CB/CP
EXC24CN
Burst/radiation noise fi ltering for audio circuits
The optimally magnetic-coupled ferrite beads allow for the fi ltering of both common and normal mode noises
The strong multi-layer structure provides high resistance to refl ow soldering heat and a high mounting reliability
Magnetic shield type
High Impedance : 220 to 1 kΩ (EXC24CB type)
Low Resistance Value : 0.4 Ω max. (EXC24CP type)
High Impedance : 600 Ω, Low Resistance Value : 0.9 Ω max. (EXC24CN type)
RoHS compliant
Smart phones, Tablet PCs, DSC and Portable Music Player
Noise suppression of burst noise of Receiver/Microphone and D-class power amplifi er
Explanation of Part Numbers
Features
Recommended Applications
EXC24CB/CP Type
EXC24CN Type
Dec. 201805
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2 mode Noise Filters
– 51 –
Ferrite
Inner Conductor Electrode
E
F
A
B
D
C
43
12
43
12
Part No.
(inch size)
Dimensions (mm)
Mass
(Weight)
[mg/pc.]
ABCDEF
EXC24C
(0504)
1.00±0.15 1.25±0.15 0.50±0.10 0.20±0.15 0.65±0.10 0.35±0.10
3
Construction Dimensions in mm (not to scale)
Ratings
Category Temperature Range –40 °C to +85 °C
Circuit Confi guration (No Polarity)
The pin numbers shown here are for reference purposes
only. Confirm the actual pin number arrangement with
the exchanged specification documents.
Part Number Impedance (Open mode) Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω) max.
(Ω) at 100 MHz Tolerance(%)
EXC24CP121U 120
±25 5
500 0.3
EXC24CP221U 220 350 0.4
EXC24CB221U 220 100 0.7
EXC24CB102U 1000 50 1.5
Part Number Impedance (Common mode) Rated Voltage
(V DC)
Rated Current
(mA DC)
DC Re sis tance
(Ω) max.
(Ω) at 100 MHz Tolerance(%)
EXC24CN601X 600 ±25 5 200 0.9
Dec. 201805
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2 mode Noise Filters
– 52 –
Impedance(Ω)
Frequency(MHz)
0
100
200
300
400
500
1 10 100 1000 10000
Normal mode
Open mode
Common mode
Impedance(Ω)
Frequency(MHz)
500
400
300
200
100
01 10 100 1000 10000
Open mode
Normal mode
Common mode
(A) Open Mode (B) Common Mode (C) Normal Mode
ZZZ
Impedance(Ω)
Frequency(MHz)
0
100
200
300
400
500
1 10 100 1000 10000
Normal mode
Open mode
Common mode
Impedance(Ω)
Frequency(MHz)
1200
1000
800
600
400
200
01 10 100 1000 10000
Open mode Normal mode
Common mode
(A) Open Mode
(C) Differential Mode
(B) Common Mode
ZZ
Z
Impedance(Ω)
Frequency(MHz)
200
400
600
800
1000
1200
1400
1600
1 10 100 1000 10000
Common mode
Open mode
Differential mode
Impedance Characteristics (Typical)
Measurement Circuit
EXC24CP121U
EXC24CB221U
EXC24CP221U
EXC24CB102U
Measurement Circuit
EXC24CN601X
Attenuation Characteristics (Typical)
As for Packaging Methods, Land Pattern, Soldering Conditions and Safety Precautions,
Please see Data Files
Dec. 201805
Panasonic cm; wrupouem Cmp campauem \ Covwarlme Deswgu and specmcahons ave each sumsm m change wnhom Home Ask (adory Vur We cunem leuhrucm specmcauonS Debra pu Emma L! smely concern anse veguvdmg [Ms pradud mease be sure [a nomad us unmedmlexy -53-
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2 mode Noise Filters
– 53 –
t1
t2P1P2P0
A
B
FE
W
fD0
Chip component
Sprocket hole Compartment
Tape running direction
E
T
W
fD
fC
fA
fB
Chip component
Sprocket hole
Compartment
Tape running direction
P0P2
P1
t2
F
W
E
A
B
fD0
Packaging Methods (Taping)
Taping Reel
Embossed Carrier Taping
Standard Quantity
Embossed Carrier Dimensions
Standard Reel Dimensions
Pressed Carrier Taping
Pressed Carrier Dimensions
Part Number Size (inch) Kind of Taping Pitch (P1) Quantity
EXC14CP◻◻◻U0302 Embossed Carrier Taping 2 mm 10,000 pcs./reel
EXC24CP/CB◻◻◻U0504 4 mm 5,000 pcs./reel
EXC24CN◻◻◻X0504 Pressed Carrier Taping 2 mm 10,000 pcs./reel
Part Number fAfBfCfDE W T
EXC14C/EXC24C 180.0±3.0 60.0±1.0 13.0±0.5 21.0±0.8 2.0±0.5 9.0±0.3 11.4±1.5
Part Number A B W F E P1P2P0fD0t1t2
EXC14CP
0.75±0.10 0.95±0.10 8.0±0.2 3.50±0.05 1.75±0.10 2.0±0.1
2.0±0.1 4.0±0.1
1.5+0.1 0.25±0.05 0.85±0.15
EXC24CP/CB
1.20±0.15 1.45±0.15 8.0±0.2 3.5±0.1 1.75±0.10 4.0±0.1
2.0±0.1 4.0±0.1
1.5+0.1 0.25±0.05 0.90±0.15
0
Part Number A B W F E P1P2P0fD0t2
EXC24CN
1.14±0.10 1.38±0.15 8.0±0.2 3.5±0.1 1.75±0.10 2.0±0.1 2.0±0.1 4.0±0.1 1.5+0.1 0.68±0.10
0
0
(mm)
(mm)
(mm)
Dec. 201805
Panasonic fi—Tfi
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
2 mode Noise Filters
– 54 –
A
DCD
EF E
B
Preheating
Peak
Heating
Temperature
Time
Recommendations and precautions are described below.
<Repair with hand soldering>
Preheat with a blast of hot air or similar method. Use a soldering iron with a tip temperature of 350 °C or less.
Solder each electrode for 3 seconds or less.
Never touch this product with the tip of a soldering iron.
Temperature Time
Preheating 140 °C to 160 °C 60 s to 120 s
Main heating Above 200 °C 30 s to 40 s
Peak 235 ± 10 °C max. 10 s
Temperature Time
Preheating 150 °C to 170 °C 60 s to 120 s
Main heating Above 230 °C 30 s to 40 s
Peak max. 260 °C max. 10 s
Recommended soldering conditions for reflow
For soldering (Example : Sn-37Pb)
For lead-free soldering (Example : Sn/3Ag/0.5Cu)
· Reflow soldering shall be performed a maximum
of two times.
· Please contact us for additional information when
used in conditions other than those specified.
· Please measure the temperature of the terminals
and study every kind of solder and printed circuit
board for solderability be fore ac tu al use.
Flow soldering
· We do not recommend flow soldering , because flow soldering may cause bridges between the electrodes.
Part
Number
Dimension (mm)
ABCDEF
EXC14CP
0.80 to
1.00
0.80 0.30
0.25 to
0.35
0.30 0.20
EXC24 CP
EXC24CB
EXC24CN
1.50 to
1.90
1.10 0.50
0.50 to
0.70
0.40 0.30
Recommended Land Pattern Design
Recommended Soldering Conditions
Dec. 201805
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters/Common mode Noise Filters with ESD Suppressor/2 mode Noise Filters
– 55 –
Perfomance
Test Item Performance Requirements Test Conditions
Resistance Within Specifi ed Tolerance 25 °C
Overload Rated Voltage
Resistance to Soldering Heat ±30 % (Impedance Change) 260 °C, 10 s
Rapid Change of Temperature ±30 % (Impedance Change) –40 °C (30 min.) / +85 °C (30 min.), 200 cycles
High Temperature Exposure ±30 % (Impedance Change) 85 °C, 500 h
Damp Heat, Steady State ±30 % (Impedance Change) 60 °C, 95 %RH, 500 h
Load Life in Humidity ±30 % (Impedance Change) 60 °C, 95 %RH, Rated Current, 500 h
Dec. 201800
Panasonic A
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Common mode Noise Filters/Common mode Noise Filters with ESD Suppressor/2 mode Noise Filters
– 56 –
Safety Precautions
(Common mode Noise Filters/Array, Common mode Noise Filters/Array with ESD Suppressor, 2 mode Noise Filters)
The following are precautions for individual products. Please also refer to the common precautions for EMC Components
in this catalog.
1. Use rosin-based fl ux or halogen-free fl ux.
2. For cleaning, use an alcohol-based cleaning agent. Before using any other type, consult with our sales person in advance.
3. Do not apply shock to Common mode Noise Filters and 2 mode Noise Filters (hereafter called the fi lters) or pinch them
with a hard tool (e.g. pliers and tweezers). Otherwise, their bodies may be chipped, affecting their performance. Excessive
mechanical stress may damage the fi lters. Handle with care.
4. Store the fi lters in a location with a temperature ranging from –5 °C to +40 °C and a relative humidity of 40 % to 60 % , where
there are no rapid changes in temperature or humidity.
5. Use the fi lters within a year from the date of arrival at your company, provided that they remain packed as they were when
delivered.
May. 201901
Panasonic CDDDDDDDDDD 1—1—‘—lr—%—9:‘—1 — Q E
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor
– 57 –
E
1
Z
2
A
3
E
4
G
5
2
6
A
7
5
8
0
9
A
10
X
11
Product Code
ESD Suppressor
Size
Code
2
3
Size mm (inch)
1005 (0402)
1608 (0603)
Packaging Methods
Code
Packaging Part No.
X
EZAEG2A
Pressed Carrier Taping
2 mm Pitch, 10,000 pcs.
V
EZAEG3A
Punched Carrier Taping
4 mm Pitch, 5,000 pcs.
Design Specification
Code
A
Design Specification
Rated Voltage 30 V
Special Feature
Code
A
Special Feature
Standard
Peak Voltage
Code
50
Peak Voltage
500 V
a
b
t
W
L
Protective coating
Alumina substrate Gap electrode
Electrode
(Between)
ESD absorbent material Electrode (Outer)
ESD Suppressor
Type: EZAEG
EZAEG2A, 3A
ESD protection of high-speed data lines
Low capacitance 0.05 pF : 1005(0402) size
0.10 pF : 1608(0603) size
Good ESD suppression characteristics
Good ESD withstanding
RoHS compliant
Smart phones, Mobile phones, RF Modules, NFC and GPS
ESD suppresion of high-speed differential data line such as Antena circuit, HDMI, SATA, USB, Display Port
Explanation of Part Numbers
Construction
Circuit Confi guration
Dimensions in mm (not to scale)
Features
Recommended Applications
Part No.
(inch size)
Dimensions (mm)
Mass (Weight)
[g/1000 pcs.]
LWa b t
EZAEG2A
(0402)
1.00±0.10 0.50±0.05 0.20±0.10 0.25±0.10 0.38±0.05
0.6
EZAEG3A
(0603)
1.60±0.15 0.80±0.15 0.30±0.20 0.30±0.20 0.50±0.10
2.2
Dec. 201804
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor
– 58 –
-30
-25
-20
-15
-10
-5
0
5
1 10 100 1000 10000
Frequency(MHz)
Attenuation (dB)
-50
0
50
100
150
200
250
300
350
400
-20 0 20 40 60 80 100 120 140 160 180 200
Times (nSecs)
Volts (V)
HDMI Controller
HDMI
Rx/Tx
Antenna
Ga/As-SW
or
ASM
c
a
b
ESD Suppressor
Ratings
Frequency Characteristics
Typical Circuits Requiring Protection
Recommended Land Pattern
ESD Suppression Voltage Waveform
As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
Part Number
(inch size)
Dimensions (mm)
abc
EZAEG2A
(0402) 0.5 to 0.6 1.4 to 1.6 0.4 to 0.6
EZAEG3A
(0603) 0.7 to 0.9 2.0 to 2.2 0.8 to 1.0
Antenna circuit
HDMI circuit
(1) Capacitance = The capacitance value shall be measured under the conditions specified below.
Frequency : 1 MHz±10 %, Voltage : 1 Vrms±0.2 Vrms, Temperature : 25 °C±2 °C
Part Number (inch size) Capacitance(1) Rated Voltage Category Temperature Range
EZAEG2A50AX (0402) 0.05+0.05 pF 30 V max. 55 to +125 °C
EZAEG3A50AV (0603) 0.10+0.10 pF
–0.04
–0.08
Recommended land pattern design for ESD Suppressor is shown below.
Perfomance
Test Item Performance Requirements Test Conditions
Peak Voltage 500 V max. IEC61000-4-2, contact discharge 8 kV, Peak voltage value
Clamping Voltage 100 V max. IEC61000-4-2, contact discharge 8 kV,
voltage at 30 ns after initiation of pulse
Leakage Current 1 A max. Current at Rated voltage (DC 30 V)
ESD withstanding Leakage current 10 A max. IEC61000-4-2, contact discharge 8 kV, +/– 10 times
Rapid Change of Temperature Leakage current 10 A max. –55 °C (30 min.) /+125 °C (30 min.), 100 cycles
Load Life in Humidity Leakage current 10 A max. 60 °C, 90% to 95%RH, Rated voltage, 1000 h
Endurance at 85 °C Leakage current 10 A max. 85 °C, Rated voltage, 1000 h
Resistance to Soldering Heat Leakage current 10 A max. 270 °C, 10 s
Dec. 201804
o0 DDDKIDDDDID Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor
– 59 –
E
1
Z
2
A
3
E
4
G
5
2
6
N
7
5
8
0
9
A
10
X
11
Product Code
ESD Suppressor
Size
Code
1
2
Size mm (inch)
0603 (0201)
1005 (0402)
Packaging Methods
Code
X
EZAEG2N
Packaging Part No.
Pressed Carrier Taping
2 mm Pitch, 10,000 pcs.
Design Specification
Code Design Specification
N
ESD withstanding 15 kV
Rated Voltage 30 V
Special Feature
Code
A
Special Feature
Standard
Peak Voltage
Code
50
Peak Voltage
500 V C
EZAEG1N
Pressed Carrier Taping
2 mm Pitch, 15,000 pcs.
a
b
t
W
L
Protective coating
Alumina substrate Gap electrode
Electrode
(Between)
ESD absorbent material Electrode (Outer)
ESD Suppressor
Type: EZAEG
EZAEG1N, 2N
Good ESD withstanding (IEC61000-4-2 15 kV contact/air Discharge)
ESD protection of high-speed data lines
Low capacitance 0.04 pF : 0603(0201) size
0.05 pF : 1005(0402) size
Good ESD suppression characteristics
RoHS compliant
Smart phones, Mobile phones, RF Modules, NFC and GPS
ESD suppresion of high-speed differential data line such as Antena circuit, HDMI, SATA, USB, Display Port
Explanation of Part Numbers
Construction
Circuit Confi guration
Dimensions in mm (not to scale)
Features
Recommended Applications
Part No.
(inch size)
Dimensions (mm)
Mass (Weight)
[g/1000 pcs.]
LWa b t
EZAEG1N
(0201)
0.60±0.03 0.30±0.03 0.15±0.10 0.15±0.10 0.23±0.03
0.12
EZAEG2N
(0402)
1.00±0.10 0.50±0.05 0.20±0.10 0.27±0.10 0.38±0.05
0.60
Dec. 201803
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor
– 60 –
-30
-25
-20
-15
-10
-5
0
5
1 10 100 1000 10000
Frequency(MHz)
Attenuation (dB)
-50
0
50
100
150
200
250
300
350
400
-20 0 20 40 60 80 100 120 140 160 180 200
Times (nSecs)
Volts (V)
HDMI Controller
HDMI
Rx/Tx
Antenna
Ga/As-SW
or
ASM
c
a
b
ESD Suppressor
Frequency Characteristics
Typical Circuits Requiring Protection
Recommended Land Pattern
ESD Suppression Voltage Waveform
As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
Part Number
(inch size)
Dimensions (mm)
abc
EZAEG1N
(0201) 0.3 to 0.4 0.8 to 0.9 0.25 to 0.35
EZAEG2N
(0402) 0.5 to 0.6 1.4 to 1.6 0.40 to 0.60
Antenna circuit
HDMI circuit
Recommended land pattern design for ESD Suppressor is shown below.
Ratings
(1) Capacitance = The capacitance value shall be measured under the conditions specified below.
Frequency : 1 MHz±10 %, Voltage : 1 Vrms±0.2 Vrms, Temperature : 25 °C±2 °C
Part Number (inch size) Capacitance(1) Rated Voltage Category Temperature Range
EZAEG1N50AC (0201) 0.04+0.04 pF 30 V max. 55 to +125 °C
EZAEG2N50AX (0402) 0.05+0.05 pF
–0.03
–0.04
Perfomance
Test Item
Performance Requirements
Test Conditions
Peak Voltage 500 V max. IEC61000-4-2, contact discharge 8 kV, Peak voltage value
Clamping Voltage 100 V max. IEC61000-4-2, contact discharge 8 kV,
voltage at 30 ns after initiation of pulse
Leakage Current 1 A max. Current at Rated voltage (DC 30 V)
ESD withstanding
Leakage current 10 A max.
IEC61000-4-2, contact discharge 15 kV or air discharge 15 kV, +/– 50 times
Rapid Change of Temperature Leakage current 10 A max.
–55 °C (30 min.) /+125 °C (30 min.), 100 cycles
Load Life in Humidity
Leakage current 10 A max.
60 °C, 90% to 95%RH, Rated voltage, 1000 h
Endurance at 85 °C
Leakage current 10 A max.
85 °C, Rated voltage, 1000 h
Resistance to Soldering Heat
Leakage current 10 A max.
270 °C, 10 s
Dec. 201803
., E] LII-J r 1—? Ci IDCDDDDIDDI Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor Array
– 61 –
E
1
Z
2
A
3
E
4
G
5
C
6
A
7
5
8
0
9
A
10
V
11
Product Code
ESD Suppressor
Size
Code
C
Size mm (inch)
2012 (0805)
4 Line use
Packaging Methods
Code
V
Packaging
Punched Carrier Taping
4 mm Pitch, 5,000 pcs.
Design Specification
Code
A
Design Specification
Rated Voltage 15 V
Special Feature
Code
A
Special Feature
Standard
Peak Voltage
Code
50
Peak Voltage
500 V
45
61
23
(0.5)
2.0±0.1
0.20±0.15 0.30±0.15
8710 9
1.25±0.10
0.25±0.15
0.35±0.15
0.50±0.10
GND
Electrode
(Outer)
Marking
Protective coating Alumina substrate
Electrode
(Outer)
GND terminal : 1, 6
I/O terminal : 2 to 5, 7 to 10
16
10 9 8 7
2345
ESD Suppressor Array
Type: EZAEGCA
4 ESD suppressors in one package
ESD protection of high-speed data lines
Low capacitance (0.25 pF)
Good ESD suppression characteristics
Good ESD withstanding
RoHS compliant
AV equipment (LCD-TV, DVD/Blu-ray drives), Information equipment (PCs, HDD,)
ESD suppresion of high-speed differential data line such as USB3.0, HDMI, Display Port
Explanation of Part Numbers
Construction
Circuit Confi guration
Dimensions in mm (not to scale)
Features
Recommended Applications
( ) Reference
Mass (Weight) [1000 pcs.] :4 g
Dec. 201803
Panasonic TI fi:’ ‘7]:- - “”" w -
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor Array
– 62 –
-50
0
50
100
150
200
250
300
350
400
-20 0 20 40 60 80 100 120 140 160 180 200
Times (nSecs)
Volts (V)
HDMI Controller
HDMI
Rx/Tx
e
a
h
g
c
Pb
d
Land pattern
Ratings
Typical Circuits Requiring Protection
Recommended Land Pattern
ESD Suppression Voltage Waveform
As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
HDMI circuit
Recommended land pattern design for ESD Suppressor Array is shown below.
abcd
Dimensions
(mm) 0.75 0.25 1.70 0.35
ehgP
Dimensions
(mm) 1.85 2.60 0.25 0.50
(1) Capacitance = The capacitance value shall be measured under the conditions specified below.
Frequency : 1 MHz±10 %, Voltage : 1 Vrms±0.2 Vrms, Temperature : 25 °C±2 °C
(2) Rated voltage between I/O terminal and GND.
(3) Rated current between input terminal and output terminal.
Part Number
(inch size) Capacitance(1) Rated Voltage(2) Rated Current(3) Category
Temperature Range
EZAEGCA50AV (0805) 0.25+0.05 pF 15 V max. 100 mA max. –55 to +125 °C
–0.10
Perfomance
Test Item Performance Requirements Test Conditions
Peak Voltage 500 V max. IEC61000-4-2, contact discharge 8 kV, Peak voltage value
Clamping Voltage 100 V max. IEC61000-4-2, contact discharge 8 kV,
voltage at 30 ns after initiation of pulse
Leakage Current 1 A max. Current at Rated voltage (DC 15 V)
ESD withstanding Leakage current 10 A max. IEC61000-4-2, contact discharge 8 kV, +/– 10 times
Rapid Change of Temperature Leakage current 10 A max. –55 °C (30 min.) /+125 °C (30 min.), 100 cycles
Load Life in Humidity Leakage current 10 A max. 60 °C, 90% to 95%RH, Rated voltage, 1000 h
Endurance at 85 °C Leakage current 10 A max. 85 °C, Rated voltage, 1000 h
Resistance to Soldering Heat Leakage current 10 A max. 270 °C, 10 s
Dec. 201803
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor, High Withstanding Type
– 63 –
E
1
Z
2
A
3
E
4
G
5
3
6
W
7
1
8
1
9
A
10
V
11
Product Code
ESD Suppressor
Size
Code
3
Size mm (inch)
1608 (0603)
Packaging Methods
Code
Packaging Part No.
V
EZAE3W
Punched Carrier Taping
4 mm Pitch, 4,000 pcs.
Design Specification
Code
W
Design Specification
High with standing type
Rated voltage 50 V
Special Feature
Code
A
Special Feature
Standard
Peak Voltage
Code
11
Peak Voltage
1000 V
L
T
W
aa
ESD Suppressor, High Withstanding Type
Type: EZAEG
EZAEG3W
Excellent ESD withstanding (Conforms with automotive ESD standards (ISO10605, air discharge 25 kV))
Low capacitance 0.10 pF : 1608 (0603) size
High rated voltage (DC 50 V) contributes to reduce the risk of communication error
AEC-Q200 qualifi ed
RoHS compliant
High speed data line for automotive (CAN, Ethernet, USB, LVDS)
Automotive Antenna
Amusement eqipment
Part No.
(inch size)
Dimensions (mm)
Mass (Weight)
[g/1000 pcs.]
LWT a
EZAEG3W
(0603)
1.60±0.15 0.80±0.15 0.80±0.15 0.30±0.20
3.8
Inner electrode Discharge area
(Hollow inside)
Features
Recommended Applications
Explanation of Part Numbers
Construction Dimensions in mm (not to scale)
Circuit Confi guration
Terminal electrode
Insulating ceramic
Dec. 201801
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor, High Withstanding Type
– 64 –
-30
-25
-20
-15
-10
-5
0
5
1 10 100 1000 10000
Frequency(MHz)
Attenuation (dB)
-200
0
200
400
600
800
1000
-20 0 20 40 60 80 100 120 140 160 180
Times (nSecs)
Volts (V)
Antenna
TVS
Protected device
FET, LNA
ESD
Suppressor
DC cut
Capacitor
Transceiver
IC
IF
Common mode
Choke coil
ESD
Suppressor
c
a
b
ESD Suppressor
(1) Capacitance = The capacitance value shall be measured under the conditions specified below.
Frequency : 1 MHz±10 %, Voltage : 1 Vrms±0.2 Vrms, Temperature : 25 °C±2 °C
Part Number (inch size) Capacitance(1) Rated Voltage Category Temperature Range
EZAEG3W11AV (0603) 0.10+0.10 pF 50 V max. 55 to +125 °C
–0.08
Ratings
Automotive antenna
Automotive network (CAN, Ethernet)
Part Number
(inch size)
Dimensions (mm)
abc
EZAEG3W
(0603) 0.8 to 1.0 2.0 to 2.6 0.8 to 1.0
Recommended land pattern design for ESD Suppressor is shown below.
As for Packaging Methods, Soldering Conditions and Safety Precautions,
Please see Data Files
Frequency Characteristics ESD Suppression Voltage Waveform
Typical Circuits Requiring Protection
Recommended Land Pattern
Perfomance
Test Item Performance Requirements Test Conditions
Peak Voltage 1000 V max. ISO10605, air discharge 15 kV, Peak voltage value
Leakage Current 1 A max. Current at Rated voltage (DC 50 V)
ESD withstanding Leakage current 10 A max. ISO10605, air discharge 25 kV, +/– 50 times
Rapid Change of Temperature Leakage current 10 A max. –55 °C (30 min.)/+125 °C (30 min.), 100 cycles
Load Life in Humidity Leakage current 10 A max. 85 °C, 85%RH, Rated voltage, 1000 h
Endurance at 125 °C Leakage current 10 A max. 125 °C, Rated voltage, 1000 h
Resistance to Soldering Heat Leakage current 10 A max. 270 °C, 10 s
Dec. 201801
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ESD Suppressor/Array
– 65 –
fN
W2
W1
fA
fC
TT A
P0
P2
P1
P1
fD0
B
F
W
E
(2 mm Pitch)
Pressed
Carrier
Punched
Carrier
Preheating
Peak
Heating
Temperature
Time
Recommended Soldering Conditions
Packaging Methods (Taping)
Standard Quantity
Part Number Size (inch) Kind of Taping Pitch (P1)Quantity
EZAEG1N 0201 Pressed Carrier Taping 2 mm 15,000 pcs./reel
EZAEG2A,2N 0402 10,000 pcs./reel
EZAEG3A 0603
Punched Carrier Taping 4 mm
5,000 pcs./reel
EZAEG3W 0603 4,000 pcs./reel
EZAEGCA 0805 5,000 pcs./reel
Taping Reel
Carrier Taping (Unit : mm)
Part Number ABWFE
EZAEG1N
0.38±0.05 0.68±0.05
8.00±0.20 3.50±0.05 1.75±0.10
EZAEG2A,2N
0.70±0.05 1.20±0.05
EZAEG3A
1.10±0.10 1.90±0.10
EZAEG3W
0.91±0.10 1.82±0.10
EZAEGCA
1.55±0.15 2.30±0.20
Part Number P1P2P00D0T
EZAEG1N
2.00±0.10
2.00±0.05 4.00±0.10 1.50+0.10
0.42±0.05
EZAEG2A,2N
0.60±0.05
EZAEG3A
4.00±0.10
0.70±0.05
EZAEG3W
1.08±0.10
EZAEGCA
0.85±0.05
0
Part Number 0A0N0CW
1W2
EZAEG1N
180.0 0 60.0+1.0 13.0±0.2 9.0+1.0 11.4±1.0
EZAEG2A,2N
EZAEG3A
EZAEG3W
EZAEGCA
–1.5 0 0
Temperature Time
Preheating 140 °C to 160 °C 60 s to 120 s
Main heating Above 200 °C 30 s to 40 s
Peak 235 ± 5 °C max. 10 s
Temperature Time
Preheating 150 °C to 180 °C 60 s to 120 s
Main heating Above 230 °C 30 s to 40 s
Peak max. 260 °C max. 10 s
Recommended soldering conditions for reflow
For soldering (Example : Sn/Pb)
For lead-free soldering (Example : Sn/Ag/Cu)
Safety Precautions
The following are precautions for individual products. Please also refer to the common precautions for ESD Suppressor in this catalog.
1.
If a large electric surge (especially, one which is larger than an ESD) is expected to be applied, be sure to test and confirm proper
ESD Suppressor (hereafter called the suppressors) functionality when mounted on your board. When the applied load is more than the
allowable rated power under normal load conditions, it may impair performance and/or the reliability of the suppressors. Never exceed
the rated power. If the product will be used under these special conditions, be sure to contact a Panasonic representative first.
2.
Do not use halogen-based or other high-activity flux. Otherwise, the residue may impair the suppressors' performance and/or reliability.
3. When soldering with a soldering iron, never touch the suppressors' bodies with the tip of the soldering iron. When using a
soldering iron with a high temperature tip, finish soldering as quickly as possible (within three seconds at 350 °C max.).
4. Avoid excessive bending of printed circuit boards in order to protect the suppressors from abnormal stress.
5. Do not immerse the suppressors in solvent for a long time. Before using solvent, carefully check the effects of im mer sion.
6. The suppressors, including the solderability, is guaranteed for a year from the date of arrival at your company, provided
that they remain packed as they were when delivered and stored at a temperature of 5 °C to 35 °C and a relative
humidity of 45 % to 85 %.
· Reflow soldering shall be performed a maximum
of two times.
· Please contact us for additional information when
used in conditions other than those specified.
· Please measure the temperature of the terminals
and study every kind of solder and printed circuit
board for solderability be fore ac tu al use.
(Unit : mm)
Recommendations and precautions are described below
Apr. 201705
DCDKDDCDDDD Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 66 –
5
4
3
2
1
10 pF
20 pF
27 pF
47 pF
56 pF
B
R
D
E
W
68 pF
100 pF
150 pF
220 pF
F
G
H
J
E
1
Z
2
J
3
P0
4567891011
0
1
V 2 7 0 E
Product Code
Size Code
0402/EIA
0603/EIA
V
Packaging Style Code Nominal Varitor Voltage
0402,0603 Paper Taping
Z
P
Series Code
EZJZ series
EZJP series
Automotive grade
(Example)
M
Capacitance Code
The first and second digits denote
the first 2 numbers of the varistor
voltage and the third digit indicates
the number of zeros following.
The decimal point denotes in R.
L
T
W
L1L2
No. Name
1Zinc oxide-based ceramics
2Internal electrode
3
Terminal electrode
Substrate electrode
4Intermediate electrode
5External electrode
Size Code Size(inch) L W T L1, L2
0 0402/EIA 1.00±0.05 0.50±0.05 0.50±0.05 0.2±0.1
1 0603/EIA 1.6±0.1 0.8±0.1 0.8±0.1 0.3±0.2
Multilayer Varistor (Automotive Grade)
Series: EZJZ-M, EZJP-M
Explanation of Part Numbers
Construction
Features
Excellent ESD suppression due to original advanced material technology
Having large electrostatic resistance meeting IEC61000-4-2, ISO10605
Having no polarity (bipolar) facilitated replacing Zener Diodes. Capable of replacing 2 Zener Diodes and 1 Capacitor.
Lead-free plating terminal electrodes enabling great solderability
Wide range of products is available by adopting multilayer structure, meeting various needs.
AEC-Q200 qualifi ed
RoHS compliant
As for Packaging Methods, Handling Precautions
Please see Data Files
Dimensions in mm (not to scale)
Oct. 201806
Panasonic I... . .I‘: oboO+¢o¢o
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 67 –
3.7
3 5 12 24 40
6.7
5.6
11
13
16
26
30
40
Circuit voltage DC (V)
Maximum allowable voltage
DC (V)
Wide variety of products is available by adopting
multilayer construction, which achieved wide
range of usage, such as application to DC
voltage lines and signal lines.
Circuit voltage
Engine ECU
Various body ECU
Communication line, such as CAN, LIN
Audio,Navigation
LED Light
Control SW
Varistor voltage : 18 to 100 V [at 1m A]
Capacitance : 10 to 220 pF max. [at 1M Hz]
Maximum Allowable Voltage Maximum DC Voltage that can be applied continuously within the operating temperature range
Varistor Voltage Varistor starting voltage between terminals at DC 1 mA, also known as Breakdown voltage
Maximum Peak Current Maximum current that can be withstood under the standard pulse 8/20 µs, 2 times based
Maximum ESD Maximum voltage that can be withstood under ESD
Features Recommended Applications
Ratings and Characteristics
Operating Temperature Range : EZJP serie –55 to 150 °C
EZJZ serie –55 to 125 °C
Recommend soldering method : Reflow soldering
Size Part No.
Maximum
allowable
voltage
DC (V)
Nominal
varistor
voltage
at 1m A (V)
Capacitance (pF)
Maximum
peak current
at 8/20µs, 2 times
(A)
Maximum ESD
at 1M Hz at 1k Hz
IEC61000-4-2
150p F/ 330 Ω
ISO10605
330p F/ 2k Ω
0402
/EIA
EZJP0V180HM 11 18 150 max. [ 120 typ.] 140 typ. 10
Contact
discharge
8k V
Contact
discharge
25k V
EZJP0V220HM 13 22 150 max. [ 100 typ.] 116 typ. 10
EZJP0V270GM 18 27 100 max. [ 85 typ.] 100 typ. 10
EZJP0V270EM 18 27 47 max. [ 33 typ.] 37 typ. 4
EZJP0V270RM 18 27 20 max. [ 15 typ.] 16.5 typ. 2
EZJP0V270BM 18 27 10 max. [ 8 typ.] 10 typ.
EZJP0V330GM 25 33 100 max. [ 85 typ.] 100 typ. 10
EZJP0V420WM 30 42 56 max. [ 40 typ.] 45 typ. 6
EZJP0V650DM 40 65 27 max. [ 22 typ.] 33 typ. 2
EZJP0V101BM 30 100 10 max. [ 8 typ.] 10 typ.
0603
/EIA
EZJP1V180JM 11 18 220 max. [180 typ.] 210 typ. 20
EZJP1V220JM 13 22 220 max. [160 typ.] 185 typ. 10
EZJP1V270GM 18 27 100 max. [ 85 typ.] 100 typ. 10
EZJP1V270EM 18 27 47 max. [ 33 typ.] 37 typ. 5
EZJP1V270RM 18 27 20 max. [ 15 typ.] 16.5 typ. 2
EZJP1V330GM 25 33 100 max. [ 85 typ.] 100 typ. 10
EZJP1V420FM 30 42 68 max. [ 55 typ.] 63 typ. 8
EZJP1V650DM 40 65 27 max. [ 22 typ.] 33 typ. 2
EZJZ1V180JM 11 18 220 max. [180 typ.] 210 typ. 20
EZJZ1V220JM 13 22 220 max. [160 typ.] 185 typ. 20
EZJZ1V270GM 16 27 100 max. [ 85 typ.] 100 typ. 20
EZJZ1V330GM 26 33 100 max. [ 85 typ.] 100 typ. 20
EZJZ1V420FM 30 42 68 max. [ 55 typ.] 63 typ. 15
EZJZ1V650DM 40 65 27 max. [ 22 typ.] 33 typ. 5
Oct. 201806
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 68 –
Current (A)
Zener diode
Zener diode
monopolar 2pcs.
Multilayer Varistor
Capacitor 1 pc.
Voltage (V)
Time (ns)
Voltage (V)
1400
1200
1000
800
600
400
200
0
-200
–20 0 20 40 60 80 100 120 140 160 180 200
Without Varistor
EZJP0V270EM
[V1m A : 27 V, C1M Hz : 47p F max.]
Attenuator : 60 dB
MLCV
150 pF
330 Ω50 Ω
Electrostatic discharger
Oscillo-scope
Mounting area
Approx .83 % space saving
MLCV
Size 0402
Zener diode
S-79
1.5
2.6
0.5
1.7
0.3
MLCC
Size 0402
Varistor Characteristics and Equivalent Circuit
ESD Suppressive Effects
Replacement of Zener diode
A Multilayer Varistor does not have an electrical polarity like zener diodes and is equivalent to total 3 pcs.
of 2 zener diodes and 1 capacitor. [Equivalent Circuit]
[ESD suppressed waveform]
Typical effects of ESD suppression
Test conditions: IEC61000-4-2 Level 4 Contact discharge, 8k V
Replacing “Zener diode and Capacitor” with Multilayer Varistor saves both the mounting area and number
of components used.
IEC61000-4-2 ··· International Standard of the ESD testing method (HBM) for electronic equipment ability to
withstand ESD generated from a human body. It sets 4 levels of severity
Severity Level 1 Level 2 Level 3 Level 4
Contact discharge 2k V 4k V 6k V 8k V
Air discharge 2k V 4k V 8k V 15k V
Dimensions in mm
Oct. 201806
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 69 –
Performance and Testing Methods
Characteristics Specifi cations Testing Method
Standard test
conditions
Electrical characteristics shall be measured under the following conditions.
Temp. : 5 to 35 °C, Relative humidity : 85 % or less
Varistor voltage To meet the specifi ed
value.
The Varistor voltage is the voltage (VC,or VcmA) between both end terminals of a
Varistor when speci ed current (CmA) is applied to it. The measurement shall be
made as quickly as possible to avoid heating effects.
Maximum
allowable voltage
To meet the specifi ed
value. The maximum DC voltage that can be applied continuously to a varistor.
Capacitance To meet the specifi ed
value.
Capacitance shall be measured at the specifi ed frequency, bias voltage 0 V,
and measuring voltage 0.2 to 2 Vrms.
Maximum peak
current
To meet the specifi ed
value.
The maximum current measured (Varistor voltage tolerance is within ±10 %)
when a standard impulse current of
8/20 µ seconds is applied twice with an interval of 5 minutes.
Maximum ESD To meet the specifi ed
value.
The maximum ESD measured (while the varistor voltage is within blow ranges
of its nominal value) when exposed to ESD 10 times ( ve times for each positive
negative polarity) based on IEC61000-4-2, ISO10605.
EZJP□□□□□□M : within±10 %, EZJZ□□□□□□M : within±30 %
Solder ability To meet the specifi ed
value.
The part shall be immersed into a soldering bath under the conditions below.
Solder : Sn-Ag-Cu
Soldering fl ux : Ethanol solution of rosin (Concentration approx. 25 wt%)
Soldering temp. : 230±5 °C
Period : 4±1 s
Soldering position : Immerse both terminal electrodes until they are completely
into the soldering bath.
Resistance to
soldering heat ΔVc / Vc : within ±10 %
After the immersion, leave the part for 24 ±2 hours under the standard condition,
then evaluate its characteristics.Soldering conditions are specifi ed below:
Soldering conditions : 270 °C, 3 s / 260 °C, 10 s
Soldering position : Immerse both terminal electrodes until they are completely
into the soldering bath.
Temperature
cycling ΔVc / Vc : within ±10 %
After repeating the cycles stated below for specified number of times, leave
the part for 24±2 hours, then evaluate its characteristics.
Cycle : 2000 cycle
Step Temperature Period
1 Max. Operating Temp. 30±3 min
2 Ordinary temp. 3 min max.
3 Min. Operating Temp. 30±3 min
4 Ordinary temp. 3 min max.
Vibration ΔVc / Vc : within ±10 %
The varistor shall be soldered on the testing board shown in Fig.3.
G force : 5 G
Vibration frequency range : 10 to 2000 Hz
Sweet time : 20 min.
Sweet direction : 12 cycles for 3 courses perpendicular each other
Mechanical Shock ΔVc / Vc : within ±10 %
The varistor shall be soldered on the testing board shown in Fig.3.
Shock-wave formation : Half sine
G force : 50 G
Shock direction : 6 directions of X, Y, Z, for each three times
Biased Humidity ΔVc / Vc : within ±10 %
After conducting the test under the conditions specifi ed below, leave the part
24±2 hours, then evaluate its characteristics.
Temp. : 85±2 °C
Humidity : 80 to 85 %RH
Applied voltage : Maximum allowable voltage (Individually specifi ed)
Period : 2000+24 / 0 h
High temperature
exposure
(dry heat)
ΔVc / Vc : within ±10 %
After conducting the test under the conditions specifi ed below, leave the part
24 ±2 hours, then evaluate its characteristics.
Temp. : Maximum operating temperature ±3 °C (Individually specifi ed)
Applied voltage : Maximum allowable voltage (Individually specifi ed)
Period : 2000+24 / 0h
Oct. 201806
Panasonic muummg yum Am W ‘J‘ ‘ ‘Wmemem
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 70 –
Feeding hole Chip pocket
t1
t2
fD0
A
B
F
W
E
t2Chip component
Feeding hole Chip pocket
fD0
P1P2P0Tape running direction
EF
W
B
A
t1
100 min.
Vacant position
400 min.
Cover tape
160 min.
Vacant position
E
C
D
A
W1
W2
B
Tape end
Symbol A B W F E P1P2P0fD0t1t2
Dim
(mm) 1.0
±0.1 1.8
±0.1 8.0
±0.2 3.50
±0.05 1.75
±0.10 4.0
±0.1 2.00
±0.05 4.0
±0.1
1.5
+0.1
0
1.1
max. 1.4
max.
Dimensions in mm
Symbol
ABCDEW
1W2
Dima
(mm)
f180–3 f60.0+1.0 13.0±0.5 21.0±0.8
2.0±0.5 9.0+1.0 11.4±1.0
0
0
0
Symbol A B W F E P1P2P0fD0t1t2
Dim
(mm) 0.62
±0.05 1.12
±0.05 8.0
±0.2 3.50
±0.05 1.75
±0.10 2.00
±0.05 2.00
±0.05 4.0
±0.1
1.5
+0.1
0
0.7
max. 1.0
max.
Series Size Code Thickness
(mm) Kind of Taping Pitch
(mm)
Q’ty
(pcs./reel)
EZJZ, EZJP 0 (0402) 0.5 Punched Carrier Taping 2 10,000
1 (0603) 0.8 4 4,000
Standard Packing Quantity
Pitch 2mm (Punched Carrier Taping) : Size 0402 Pitch 4mm (Punched Carrier Taping) : Size 0603
Reel for Taping
Packaging Methods
Leader Part and Taped End
Leader part
Oct. 201806
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 71 –
Handling Precautions
Multilayer Varistors, Chip Type (Automotive Grade)
Series: EZJZ-M, EZJP-M
Safety Precautions
Multilayer Varistors for Automotive (hereafter referred to as “Varistors”) should be used for general purpose applications
as countermeasures against ESD and noise found in vehicle electronics (Engine ECU and various body ECU,
accessory equipment, etc.) equipment. When subjected to severe electrical, environmental, and/or mechanical stress
beyond the specifications, as noted in the Ratings and Specified Conditions section, the Varistors’ performance may be
degraded, or become failure mode, such as short circuit mode and open-circuit mode.
If you use under the condition of short-circuit, heat generation of Varistors will occur by running large current due to
application of voltage. There are possibilities of smoke emission, substrate burn-out, and, in the worst case, fire.
For products which require high safety levels, please carefully consider how a single malfunction can affect your
product. In order to ensure the safety in the case of a single malfunction, please design products with fail-safe, such
as setting up protecting circuits, etc.
For the following applications and conditions, please contact us for additional specifications, which is not found
in this document.
· When your application may have difficulty complying with the safety or handling precautions specified below.
· High-quality and high-reliability required devices that have possibility of causing hazardous conditions, such
as death or injury (regardless of directly or indirectly), due to failure or malfunction of the product.
1 Aircraft and Aerospace Equipment (artificial satellite, rocket, etc.)
2 Submarine Equipment (submarine repeating equipment, etc.)
3 Transportation Equipment (airplanes, trains, ship, traffic signal controllers, etc.)
4
Power Generation Control Equipment (atomic power, hydroelectric power, thermal power plant control system, etc.)
5 Medical Equipment (life-support equipment, pacemakers, dialysis controllers, etc.)
6 Information Processing Equipment (large scale computer systems, etc.)
7 Electric Heating Appliances, Combustion devices (gas fan heaters, oil fan heaters, etc.)
8 Rotary Motion Equipment
9 Security Systems
J And any similar types of equipment
Strict Observance
1. Confirmation of Rated Performance
The Varistors shall be operated within the specified rating/performance.
Applications exceeding the specifications may cause deteriorated performance and/or breakdown, resulting in
degradation and/or smoking or ignition of products. The following are strictly observed.
(1) The Varistors shall not be operated beyond the specified operating temperature range.
(2) The Varistors shall not be operated in excess of the specified maximum allowable voltage.
(3) The Varistors shall not be operated in the circuits to which surge current and ESD that exceeds the specified
maximum peak current and maximum ESD.
(4) Never use for AC power supply circuits.
2. The Varistors shall not be mounted near flammables.
1. Circuit Design
1.1
Operating Temperature and Storage Temperature
When operating a components-mounted circuit,
please be sure to observe the “Operating
Temperature Range”, written in delivery
specifications. Storage temperature of PCB after
mounting Varistors, which is not operated, should be
within the specified “Storage Temperature Range” in
the delivery specifications. Please remember not to
use the product under the condition that exceeds
the specified maximum temperature.
1.2 Operating Voltage
The Varistors shall not be operated in excess of
the “Maximum allowable voltage”. If the Varistors
are operated beyond the specified Maximum
allowable voltage, it may cause short and/or
damage due to thermal run away.
The circuit that continuously applies high
frequency and/or steep pulse voltage please
examines the reliability of the Varistor even if it is
used within a “Maximum allowable voltage”. Also,
it would be safer to check also the safety and
reliability of your circuit.
Operating Conditions and Circuit Design
May. 201903
Panasonic / W W ‘ ‘ ‘ L A but! Helrohl vvvvv
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 72 –
Land
SMD
ab
c
Solder resist
(a) Excessive amount (b) Proper amount (c) Insufficient amount
Solder resist
Land
Portion to be
Excessively soldered
A lead wire of
Retrofitted
component
Soldering
iron
Solder
(ground solder)
Chassis
Electrode pattern
Solder resist
Solder resist
Solder resist
The lead wire of a
Component With lead wires
1.3 Self-heating
The surface temperature of the Varistors shall
be under the specified Maximum Operating
Temperature in the Specifications including the
temperature rise caused by self-heating. Check
the temperature rise of the Varistor in your circuit.
1.4 Environmental Restrictions
The Varistors shall not be operated and/or stored
under the following conditions.
(1) Environmental conditions
(a) Under direct exposure to water or salt water
(b) Under conditions where water can condense
and/or dew can form
(c) Under conditions containing corrosive gases
such as hydrogen sulfide, sulfurous acid,
chlorine and ammonia
(2) Mechanical conditions
The place where vibration or impact that
exceeds specified conditions written in
delivery specification is loaded.
2. Design of Printed Circuit Board
2.1 Selection of Printed Circuit Boards
There is a possibility of performance deterioration
by heat shock (temperature cycles), which causes
cracks, from alumina substrate.
Please confirm that the substrate you use does
not deteriorate the Varistors’ quality.
2.2 Design of Land Pattern
(1) Recommended land dimensions are shown below.
Use the proper amount of solder in order to
prevent cracking. Using too much solder places
excessive stress on the Varistors.
Recommended Land Dimensions
Unit (mm)
(2) The land size shall be designed to have equal
space, on both right and left side. If the amount
of solder on the right land is different from that
of the left land, the component may be cracked
by stress since the side with a larger amount of
solder solidifies later during cooling.
Recommended Amount of Solder
2.3 Utilization of Solder Resist
(1) Solder resist shall be utilized to equalize the
amounts of solder on both sides.
(2) Solder resist shall be used to divide the pattern
for the following cases;
· Components are arranged closely.
· The Varistor is mounted near a component
with lead wires.
· The Varistor is placed near a chassis.
See the table below.
Prohibited Applications and Recommended Applications
Item Prohibited
applications
Improved applications
by pattern division
Mixed mounting
with a component
with lead wires
Arrangement near
chassis
Retro-fi tting of
component with
lead wires
Lateral
arrangement
2.4 Component Layout
To prevent the crack of Varistors, place it on the
position that could not easily be affected by the
bending stress of substrate while going through
procedures after mounting or handling.
(1) To minimize mechanical stress caused by the
warp or bending of a PC board, please follow
the recommended Varistors’ layout below.
Prohibited layout Recommended layout
Layout the Varistors sideways
against the stressing direction.
Size Code
(EIA)
Component dimensions abc
LW T
0(0402)
1.0 0.5 0.5 0.4 to 0.5 0.4 to 0.5 0.4 to 0.5
1(0603)
1.6 0.8 0.8 0.8 to 1.0 0.6 to 0.8 0.6 to 0.8
May. 201903
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 73 –
AB
C
E
D
Slit
Magnitude of stress A>B=C>D>E
Perforation
Supporting
pin
Supporting
pin
Crack
Separation of solder
Crack
(2) The following layout is for your reference since
mechanical stress near the dividing/breaking
position of a PC board varies depending on
the mounting position of the Varistors.
(3) The magnitude of mechanical stress applied
to the Varistors when dividing the circuit board
in descending order is as follows: push back
< slit < V-groove < perforation. Also take into
account the layout of the Varistors and the
dividing/breaking method.
2.5 Mounting Density and Spaces
Intervals between components should not be too
narrow to prevent the influence from solder bridges
and solder balls. The space between components
should be carefully determined.
1. Storage
(1) The Varistors shall be stored between 5 to
40 °C and 20 to 70 % RH, not under severe
conditions of high temperature and humidity.
(2) If stored in a place where humidity, dust, or
corrosive gasses (hydrogen sulfide, sulfurous
acid, hydrogen chloride and ammonia, etc.) are
contained, the solderability of terminals electrodes
will be deteriorated.
In addition, storage in a place where the heat
or direct sunlight exposure occurs will causes
mounting problems due to deformation of tapes
and reels and components and taping/reels
sticking together.
(3) Do not store components longer than 6 months.
Check the solderability of products that have
been stored for more than 6 months before use.
2. Adhesives for Mounting
(1) The amount and viscosity of an adhesive for
mounting shall be such that the adhesive will
not flow off on the land during its curing.
(2) If the amount of adhesive is insufficient for
mounting, the Varistors may fall off after or
during soldering.
(3) L o w -v i scosity of the adhesive causes
displacement of Varistors.
(4) The heat-curing methods for adhesive are
ultraviolet radiation, far-infrared radiation, and so
on. In order to prevent the terminal electrodes of
the Varistors from oxidizing, the curing shall be
under the following conditions:
160 °C max., for 2 minutes max.
(5) Insufficient curing may cause the Varistors to fall
off after or during soldering. In addition, insulation
resistance between terminal electrodes may
deteriorate due to moisture absorption. In
order to prevent these problems, please
observe proper curing conditions.
3. Chip Mounting Consideration
(1) When mounting the Varistors components on a
PC board, the Varistor bodies shall be free from
excessive impact loads such as mechanical
impact or stress due to the positioning, pushing
force and displacement of vacuum nozzles
during mounting.
(2) Maintenance and inspection of the Chip Mounter
must be performed regularly.
(3) If the bottom dead center of the vacuum nozzle
is too low, the Varistor will crack from excessive
force during mounting.
Pease refer to the following precautions and
recommendations.
(a) Set and adjust the bottom dead center of
the vacuum nozzles to the upper surface of
the PC board after correcting the warp of
the PC board.
(b) Set the pushing force of the vacuum nozzle
during mounting to 1 to 3 N in static load.
(c) For double surface mounting, apply a
supporting pin on the rear surface of the
PC board to suppress the bending of the
PC board in order to minimize the impact of
the vacuum nozzles. Typical examples are
shown in the table below.
(d) Adjust the vacuum nozzles so that their
bottom dead center during mounting is not
too low.
Item Prohibited mounting
Recommended mounting
Single surface
mounting
The supporting pin does not necessarily
have to be positioned beneath the
Varistor.
Double surface
mounting
Precautions for Assembly
May. 201903
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 74 –
260
240
0
Temperature(˚C)
Time
3 to 5 s
Soldering
T
Gradual cooling
(at ordinary mperature)
60 to 120 s
Gradual
cooling
5
Heating3
Peak4
Temp. rise
T
2
Preheating1
260
220
180
140
Temperature (˚C)
Time
60 to 120 s 60 s max.
(4) The closing dimensions of the positioning
chucks shall be controlled. Maintenance and
replacement of positioning chucks shall be
performed regularly to prevent chipping or
cracking of the Varistors caused by mechanical
impact during positioning due to worn
positioning chucks.
(5) Maximum stroke of the nozzle shall be adjusted
so that the maximum bending of PC board
does not exceed 0.5 mm at 90 mm span. The
PC board shall be supported by an adequate
number of supporting pins.
4. Selection of Soldering Flux
Soldering flux may seriously affect the performance
of the Varistors. Please confirm enough whether the
soldering flux have an influence on performance of the
Varistors or not, before using.
5. Soldering
5.1 Flow Soldering
When conducting flow soldering, stress from abrupt
temperature change is applied to the Varistors, so the
temperature, especially temperature of solder should
be controlled very carefully. Varistors should not be
subjected to abrupt temperature change because it
causes occurrence of thermal cracks as a result of
excessive thermal stress inside of the Varistors from
flow soldering. You should be careful to temperature
difference. Therefore it is essential that soldering
process follow these recommended conditions.
(1) Application of Soldering flux :
The soldering flux shall be applied to the
mounted Varistors thinly and uniformly by foaming
method.
(2) Preheating :
Conduct sufficient pre-heating, and make sure
that the temperature difference between solder
and Varistors’ surface is 150 °C or less.
(3) Immersion into Soldering bath :
The Varistors shall be immersed into a soldering
bath of 240 to 260 °C for 3 to 5 seconds.
(4) Gradual Cooling :
After soldering, avoid rapid cooling (forced
cooling) and conduct gradual cooling, so that
thermal cracks do not occur.
(5) Flux Cleaning :
When the Varistors are immersed into a cleaning
solvent, be sure that the surface temperatures of
devices do not exceed 100 °C.
(6) Performing flow soldering once under the
conditions shown in the figure on the right
“Recommended profile of Flow soldering (Ex.)”
will not cause any problems. However, pay
attention to the possible warp and bending of the
PC board.
5.2 Reflow Soldering
The reflow soldering temperature conditions are
composed of temperature curves of Preheating,
Temp. rise, Heating, Peak and Gradual cooling.
Large temperature difference inside the Varistors
caused by rapid heat application to the Varistors
may lead to excessive thermal stresses, contributing
to the thermal cracks. The Preheating temperature
requires controlling with great care so that
tombstone phenomenon may be prevented.
Item Temperature Period or Speed
1 Preheating 140 to 180 °C 60 to 120 s
2 Temp. rise Preheating temp
to Peak temp. 2 to 5 °C /s
3 Heating 220 °C min. 60 s max.
4 Peak 260 °C max. 10 s max.
5 Gradual cooling Peak temp.
to 140 °C 1 to 4 °C /s
Recommended profi le of Refl ow soldering (Ex.)
Recommended profi le of Flow soldering (Ex.)
T : Allowable temperature difference T < 150 °C
The rapid cooling (forced cooling) during Gradual
cooling part should be avoided, because this may
cause defects such as the thermal cracks, etc.
When the Varistors are immersed into a cleaning
solvent, make sure that the surface temperatures of
the devices do not exceed 100 °C.
Performing reflow soldering twice under the
conditions shown in the figure above “Recommended
profile of Reflow soldering (Ex.)” will not cause any
problems. However, pay attention to the possible
warp and bending of the PC board.
For products specified in individual specifications,
avoid flow soldering.
T : Allowable temperature difference
May. 201903
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 75 –
T
Preheating
60 to 120 s 3 s max.
Gradual cooling
Supporting pin
Separated, Crack
Check pin
Check pin
5.3 Hand Soldering
Hand soldering typically causes significant
temperature change, which may induce excessive
thermal stresses inside the Varistors, resulting in
the thermal cracks, etc.
In order to prevent any defects, the following
should be observed.
· Control the temperature of the soldering tips
with special care.
· Avoid the direct contact of soldering tips with
the Varistors and/or terminal electrodes.
· Do not reuse dismounted Varistors.
(1) Condition 1 (with preheating)
(a) Soldering :
Use thread solder (01 mm or below) which
contains flux with low chlorine, developed
for precision electronic equipment.
(b) Preheating :
Conduct sufficient Preheating, and make
sure that the temperature difference
between solder and Varistors’ surface is
150 °C or less.
(c) Temperature of Iron tip: 350 °C max.
(The required amount of solder shall be
melted in advance on the soldering tip.)
(d) Gradual cooling :
After soldering, the Varistors shall be
cooled gradually at room temperature.
Recommended profi le of Hand soldering (Ex.)
(2) Condition 2 (without preheating)
Hand soldering can be performed without
preheating, by following the conditions below:
(a) Soldering iron tip shall never directly touch
the ceramic and terminal electrodes of the
Varistors.
(b) The lands are sufficiently preheated
with a soldering iron tip before sliding
the soldering iron tip to the terminal
electrodes of the Varistors for soldering.
Conditions of Hand soldering without preheating
Item Condition
Temperature of Iron tip 350 °C max.
Wattage 20 W max.
Shape of Iron tip 03 mm max.
Soldering time with a soldering iron 3 s max.
6. Post Soldering Cleaning
6.1 Cleaning solvent
Soldering flux residue may remain on the PC
board if cleaned with an inappropriate solvent.
This may deteriorate the performance of Varistors,
especially insulation resistance.
6.2 Cleaning conditions
Inappropriate cleaning conditions such as
insufficient cleaning or excessive cleaning may
impair the electrical characteristics and reliability
of the Varistors.
(1) Insufficient cleaning can lead to :
(a) The halogen substance found in the residue
of the soldering flux may cause the metal of
terminal electrodes to corrode.
(b) The halogen substance found in the residue
of the soldering flux on the surface of the
Varistors may change resistance values.
(c) Water-soluble soldering flux may have more
remarkable tendencies of (a) and (b) above
compared to those of rosin soldering flux.
(2) Excessive cleaning can lead to :
(a) When using ultrasonic cleaner, make sure
that the output is not too large, so that the
substrate will not resonate. The resonation
causes the cracks in Varistors and/or
solders, and deteriorates the strength of the
terminal electrodes.
Please follow these conditions for Ultrasonic
cleaning:
Ultrasonic wave output : 20 W/L max.
Ultrasonic wave frequency : 40 kHz max.
Ultrasonic wave cleaning time : 5 min. max.
6.3 Contamination of Cleaning solvent
Cleaning with contaminated cleaning solvent may
cause the same results as that of insufficient cleaning
due to the high density of liberated halogen.
7. Inspection Process
The pressure from measuring terminal pins might
bend the PCB when implementing circuit inspection
after mounting Varistors on PCB, and as a result,
cracking may occur.
(1) Mounted PC boards shall be supported by an
adequate number of supporting pins on the back
with bend settings of 90 mm span 0.5 mm max.
(2) Confirm that the measuring pins have the right
tip shape, are equal in height, have the right
pressure and are set in the correct positions.
The following figures are for your reference to
avoid bending the PC board.
T : Allowable temperature difference T<150 °C
Prohibited setting Recommended setting
Bending of
PC board
May. 201903
Panasonic WW
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors (Automotive Grade)
– 76 –
Bending Torsion
PC board
splitting jig
V-groove
PC board
Outline of Jig
PC
board
Chip
component
Loading
point
V-groove
Loading direction
PC
board
Chip component
Loading
point
V-groove
Loading direction
Floor
Crack
Mounted PCB
Crack
8. Protective Coating
When the surface of a PC board on which the
Varistors have been mounted is coated with resin
to protect against moisture and dust, it shall be
confirmed that the protective coating does not affect
the performance of Varistors.
(1) Choose the material that does not emit the
decomposition and/or reaction gas. The Gas may
affect the composing members of the Varistors.
(2) Shrinkage and expansion of resin coating when
curing may apply stress to the Varistors and may
lead to occurrence of cracks.
9. Dividing/Breaking of PC Boards
(1) Please be careful not to stress the substrate with
bending/twisting when dividing, after mounting
components including Varistors. Abnormal and
excessive mechanical stress such as bending or
torsion shown below can cause cracking in the
Varistors.
(2) Dividing/Breaking of the PC boards shall be
done carefully at moderate speed by using a
jig or apparatus to prevent the Varistors on the
boards from mechanical damage.
(3) Examples of PCB dividing/breaking jigs:
The outline of PC board breaking jig is shown
below. When PC board are broken or divided,
loading points should be close to the jig to
minimize the extent of the bending.
Also, planes with no parts mounted on should
be used as plane of loading, in order to prevent
tensile stress induced by the bending, which
may cause cracks of the Varistors or other parts
mounted on the PC boards.
Prohibited dividing Recommended dividing
10. Mechanical Impact
(1) The Varistors shall be free from any excessive
mechanical impact. The Varistor body is made
of ceramics and may be damaged or cracked if
dropped. Never use a Varistor which has been
dropped; their quality may already be impaired,
and in that case, failure rate will increase.
(2) When handling PC boards with Varistors mounted
on them, do not allow the Varistors to collide with
another PC board.
When mounted PC boards are handled or stored
in a stacked state, the corner of a PC board
might strike Varistors, and the impact of the
strike may cause damage or cracking and can
deteriorate the withstand voltage and insulation
resistance of the Varistor.
The various precautions described above are typical.
For special mounting conditions, please contact us.
Other
May. 201903
Panasonic DD DDKDDDDCD
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 77 –
5
4
3
2
1
E
1
Z
2
J
3
Z0
4567891011 12
Z
0
1
V 2 7 0 E
Product Code
Size Code
0201
0402
0603
V
Packaging Style Code
The first and second digits
denote the first 2 numbers
of the varistor voltage and
the third digit indicates the
number of zeros following.
The decimal point denotes
in R.
Nominal Varitor Voltage
0402, 0603 Paper Taping
Z
P
Series Code
EZJZ series
EZJP series
Design Code
Design Code
(Example)
Below 3 pF, the 10 or 11th
position of the P/N indicates the
capacitance value as follows :
2.0 pF·····20, 1.5 p·····F15
Nil Cap. Tolerance : max.
Cap. Tolerance : ±0.25 pF
Cap. Tolerance : ±0.50 pF
C
D
Cap. Tolerance : ±0.1 pF
B
KCap. Tolerance : ±10 %
MCap. Tolerance : ±20 %
A
Capacitance Code
3 pF
20 pF
27 pF
47 pF
56 pF
68 pF
A
R
D
E
W
F
100 pF
150 pF
220 pF
330 pF
680 pF
G
H
J
K
M
L
T
W
L1L2
No. Name
1Semiconductive Ceramics
2Internal electrode
3
Terminal electrode
Substrate electrode
4Intermediate electrode
5External electrode
Size Code Size(inch) L W T L1, L2
Z 0201 0.60±0.03 0.30±0.03 0.30±0.03 0.15±0.05
0 0402 1.00±0.05 0.50±0.05 0.50±0.05 0.2±0.1
1 0603 1.6±0.1 0.8±0.1 0.8±0.1 0.3±0.2
Multilayer Varistor for ESD pulse
[DC voltage lines/High speed signal lines]
Series: EZJZ, EZJP
Explanation of Part Numbers
Construction
Features
Excellent ESD suppression due to original advanced material technology
Having large electrostatic resistance meeting IEC61000-4-2, Level 4 standard
Having no polarity (bipolar) facilitated replacing Zener Diodes. Capable of replacing 2 Zener Diodes and 1 Capacitor.
Lead-free plating terminal electrodes enabling great solderability
Wide range of products is available by adopting multilayer structure, meeting various needs.
Low capacitance versions for DC voltage lines of high speed busses
Ultra low capacitance for high speed signal line
Applicable to high-speed signal lines, such as interfaces (e.g. USB 2.0, IEEE1394, HDMI, and so on), due to
our original ultra-low capacitance technology.
RoHS compliant
As for Packaging Methods, Handling Precautions
Please see Data Files
Dimensions in mm (not to scale)
May. 201906
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 78 –
1000
100
10
10–6 10–5 10–4 10–3
Current (A)
Max. Leakage Current
EZJZV171AA
EZJZV171AA
EZJZV800AA
EZJZV800AA
EZJZV500AA
EZJZV500AA
Max. Clamping Voltage
Voltage (V)
10–2 10–1 100101
(Typical curve)
Multilayer Varistor, Low Capacitance Type
[High speed signal lines]
Mobile phone Antenna circuit, External IF
DSC, DVC USB2.0, IEEE1394
PC, PDA USB2.0, IEEE1394, LAN1000BASE
TV, DVD USB2.0, IEEE1394, HDMI
Game console Controller, External IF
Size Part No.
Maximum
allowable voltage
DC (V)
Nominal varistor
voltage
at 1mA (V)
Capacitance (pF)
at 1MHz
Maximum ESD
IEC61000-4-2
0402
EZJZ0V80010 10 80 1 max. [0.8 typ.]
Contact discharge : 8kV
EZJZ0V80015D 5 80 1.5±0.5
EZJZ0V500AA 5 50 3 max. [2.1 typ.]
EZJZ0V800AA 18 80 3 max. [2.1 typ.]
EZJZ0V171AA 18 170 3 max. [2.1 typ.]
0603
EZJZ1V80010 10 80 1 max. [0.8 typ.]
EZJZ1V500AA 5 50 3 max. [2.1 typ.]
EZJZ1V800AA 18 80 3 max. [2.1 typ.]
EZJZ1V171AA 18 170 3 max. [2.1 typ.]
Operating Temperature Range: –40 to 85 °C
Recommend soldering method : Reflow soldering
Features
Recommended Applications
Multilayer monolithic ceramic construction for high speed signal lines
Ideal for USB 2.0, IEEE1394, and HDMI high speed data busses
Applicable to high-speed signal lines, such as interfaces (e.g. USB 2.0, IEEE1394, HDMI, and so on), due to
our original material technology and multilayer technology.
Capacitance: 0.8 to 2.1 pF typ.
Ratings and Characteristics
Voltage vs. Current
May. 201906
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 79 –
1
0.1
1
10
100
10 100
Frequency (MHz)
Capacitance (pF)
1000 10000
3 pF max. [2.1 pF typ.]
1 pF max. [0.8 pF typ.]
1.5 pF typ.
(Typical curve)
3 pF max. [2.1 pF typ.]
1 pF max. [0.8 pF typ.]
1.5 pF typ.
1
Frequency (MHz)
Impedance (Ω)
10
10 100 1000 100001
100
1000
10000
100000
1000000
10000000
(Typical curve)
Attenuation (dB)
–40
–35
–30
–25
–20
–15
–10
–5
0
5
10
1 10 100 1000 10000
Frequency (MHz)
(Typical curve)
3 pFmax.[2.1pFtyp.]
1.5 pFtyp.
1 pFmax.[0.8pFtyp.]
Capacitance vs. Frequency Impedance vs. Frequency
Attenuation vs. Frequency
May. 201906
Panasonic r60. W‘O‘D +¢o¢n . O. +¢o§o+o¢u
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 80 –
3.7
3 5 12 24 40
6.7
5.6
11
13
16
26
30
40
Circuit voltage DC (V)
Maximum allowable voltage
DC (V)
Wide variety of products is available by adopting
multilayer construction, which achieved wide
range of usage, such as application to DC
voltage lines and signal lines.
Circuit voltage
Multilayer Varistor, Low Voltage Type (Standard Type)
[DC voltage lines/Low speed signal lines]
Mobile phone SW, LCD, LED, Audio terminal,
Battery pack, Memory card, External IF
DSC, DVC SW, LCD, LED, USB
PC, PDA SW, LCD, LED, USB
TV, DVD Audio, Video terminal
Audio Audio terminal, Microphone, Receiver
Game console Controller, External IF
Varistor voltage : 6.8 to 65 V [at 1 mA]
Capacitance : 8.5 to 420 pF typ. [at 1 MHz]
Size Part No.
Maximum
allowable
voltage
DC (V)
Nominal
varistor
voltage
at 1mA (V)
Capacitance (pF) Maximum
peak current
at 8/20µs, 2times
(A)
Maximum ESD
IEC61000-4-2
at 1MHz at 1kHz
0201
EZJPZV6R8JA 3.7 6.8 220 max. [180 typ.] 175 typ. 5
Contact discharge
8 kV
EZJPZV6R8GA 3.7 6.8 100 max. [ 85 typ.] 100 typ. 5
EZJPZV080GA 5.6 8 100 max. [ 85 typ.] 100 typ. 5
EZJPZV120GA 7.5 12 100 max. [ 85 typ.] 100 typ. 5
EZJPZV120DA 7.5 12 27 max. [ 22 typ.] 33 typ. 1
EZJPZV120RA 7.5 12 20 max. [ 15 typ.] 18 typ. 1
EZJPZV150RA 9 15 20 max. [ 15 typ.] 18 typ. 1
EZJPZV270RA 16 27 20 max. [ 15 typ.] 16.5 typ. 1
EZJPZV270BA 16 27 10 max. [8.5 typ.] 10 typ. 1
0402
EZJP0V6R8MA 3.7 6.8 680 max. [420 typ.] 650 typ. 20
EZJP0V6R8GA 3.7 6.8 100 max. [ 85 typ.] 100 typ. 3
EZJP0V080MA 5.6 8 680 max. [420 typ.] 650 typ. 20
EZJP0V080KA 5.6 8 330 max. [290 typ.] 480 typ. 15
EZJP0V080GA 5.6 8 100 max. [ 65 typ.] 100 typ. 3
EZJP0V080DA 5.6 8 27 max. [ 22 typ.] 33 typ. 1
EZJP0V120JA 6.7 12 220 max. [150 typ.] 175 typ. 10
EZJZ0V180HA 11 18 150 max. [120 typ.] 140 typ. 10
EZJZ0V220HA 13 22 150 max. [100 typ.] 116 typ. 10
EZJP0V270EA 16 27 47 max. [ 33 typ.] 37 typ. 4
EZJP0V270RA 16 27 20 max. [ 15 typ.] 16.5 typ. 1
EZJZ0V420WA 30 42 56 max. [ 40 typ.] 45 typ. 10
EZJZ0V650DA 40 65 27 max. [ 22 typ.] 33 typ. 5
0603
EZJP1V120KA 6.7 12 330 max. [250 typ.] 290 typ. 20
EZJZ1V180JA 11 18 220 max. [180 typ.] 210 typ. 20
EZJZ1V220JA 13 22 220 max. [160 typ.] 185 typ. 20
EZJZ1V270GA 16 27 100 max. [ 85 typ.] 100 typ. 20
EZJZ1V270EA 16 27 47 max. [ 33 typ.] 37 typ. 20
EZJZ1V270RA 16 27 20 max. [ 15 typ.] 16.5 typ. 3
EZJZ1V330GA 26 33 100 max. [ 85 typ.] 100 typ. 20
EZJZ1V420FA 30 42 68 max. [ 55 typ.] 63 typ. 15
EZJZ1V650DA 40 65 27 max. [ 22 typ.] 33 typ. 5
Operating Temperature Range: –40 to 85 °C
Maximum Allowable Voltage Maximum DC Voltage that can be applied continuously within the operating temperature range
Varistor Voltage Varistor starting voltage between terminals at DC 1 mA, also known as Breakdown voltage
Maximum Peak Current Maximum current that can be withstood under the standard pulse 8/20 µs, 2 times based
Maximum ESD Maximum voltage that can be withstood under ESD based on IEC61000-4-2, 10 times
(5 times of each positive-negative polarity)
Recommend soldering method : Reflow soldering
Features Recommended Applications
Ratings and Characteristics
May. 201906
Panasonic ‘ KW?“ I
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 81 –
10–6 10–5 10–4 10–3 10–2
Current (A)
10–1 100101102
300
200
100
10
1
Voltage (V)
Max. Leakage Current Max. Clamping Voltage
EZJZV420A
EZJZV330A
EZJZV270A
EZJZV220A
EZJZV180A
EZJZV120A
EZJZV650A
10–6 10–5 10–4 10–3 10–2
Current (A)
10–1 100101
100
10
1
Voltage (V)
Max. Leakage Current Max. Clamping Voltage
(Typical curve) (Typical curve)
EZJPV270RA
EZJPZV120GA
EZJPV080A
EZJPV6R8A
EZJPZV150RA
EZJPV270RA
EZJPZV120GA
EZJPV080A
EZJPV6R8A
EZJPZV150RA
EZJZV420A
EZJZV330A
EZJZV270A
EZJZV220A
EZJZV180A
EZJZV120A
EZJZV650A
0.1 1 10 100
Frequency (MHz)
Capacitance (pF)
1000 10000
330 pF max.
220 pF max.
100 pF max.
47 pF max.
20 pF max.
10000
1
10
100
1000
0.1 1 10 100
Frequency (MHz)
Capacitance (pF)
1000 10000
680 pFmax.
330 pFmax.
100 pFmax.
27 pFmax.
20 pFmax.
10000
1
10
100
1000
(Typical curve) (Typical curve)
10 pFmax.
Frequency (MHz)
Attenuation (dB)
20 pF max.
47 pF max.
100 pF max.
220 pF max.
330 pF max.
10
–50
0.1 1 10 100 1000 10000
–60
–40
–30
20
0
–10
Frequency (MHz)
Attenuation (dB)
27 pFmax.
20 pFmax.
330 pFmax.
680 pFmax.
100 pFmax.
10
–50
0.1 1 10 100 1000 10000
–60
–40
–30
20
0
–10
(Typical curve) (Typical curve)
10 pFmax.
EZJZ Series
EZJZ Series
EZJZ Series
Capacitance vs. Frequency
Attenuation vs. Frequency
EZJP Series
EZJP Series
EZJP Series
Voltage vs. Current
May. 201906
Panasonic 00¢; DDDDDDDDDDKD —\
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 82 –
5
4
3
2
1
L
T
W
L1L2
E
1
Z
2
J
3
S2
4567891011 12
Y D 4 7 2
1
2
Product Code Series Code
Size Code
0603
0805
V
Y
Packaging Style Code Nominal Capacitance
f180 reel, Paper Taping
f180 reel, Embossed Taping
Design Code
(Example)
B
Max. Allowable
Voltage Code
C
D
DC 6 V
DC 18 V
DC 30 V
The first and second
digits denote the first 2
figures of capacitance
and the third digit
indicates the number
of zeros following.
Multilayer Varistor for ESD pulse
[DC voltage lines]
Series: EZJS
Explanation of Part Numbers
Construction
Features
Excellent ESD suppression due to original advanced material technology
Having large electrostatic resistance meeting IEC61000-4-2, Special Level 30 kV standard
Having no polarity (bipolar) facilitated replacing Zener Diodes. Capable of replacing 2 Zener Diodes and 1
Capacitor.
Lead-free terminal electrodes enabling great solderability
RoHS compliant
No. Name
1Semiconductive Ceramics
2Internal electrode
3
Terminal electrode
Substrate electrode
4Intermediate electrode
5External electrode
Size Code Size(inch) L W T L1, L2
1 0603 1.60±0.15 0.8±0.1 0.8±0.1 0.3±0.2
2 0805 2.0±0.2 1.25±0.20 0.8±0.2 0.50±0.25
1.25±0.20
As for Packaging Methods, Handling Precautions
Please see Data Files
Dimensions in mm (not to scale)
May. 201906
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 83 –
Max. Leakage Current
1000
Max. Clamping Voltage
100
10
10–6 10–5 10–4 10–3 10–2
Current (A)
10–1 100101102
Voltage (V)
1
(Typical curve)
EZJS□□D□□□
EZJS□□C□□□
EZJS□□B□□□
1000 1 10 100 1000
Frequency (kHz)
10000 100000 1000000
10000
Capacitance (pF)
100000
22000 pF typ.
8200 pF typ.
4700 pF typ.
1800 pF typ.
3900 pF typ.
(Typical curve)
10
–10
–40
Frequency (kHz)
8200 pF typ.
4700 pF typ.
3900 pF typ.
1800 pF typ.
22000 pF typ.
–50
1 10 100 1000 10000 100000 1000000 10000000
–60
–70
–30
Attenuation (dB)
–20
0
(Typical curve)
Size Part No.
Maximum Allowable
Voltage
DC (V)
Nominal Varistor
Voltage
at 0.1 mA (V)
Capacitance
at 1 kHz (pF)
Maximum ESD
IEC61000-4-2
0603
EZJS1VB822 6 12 8200 typ.
Contact discharge :
30 kV
EZJS1VC392 18 30 3900 typ.
EZJS1VD182 30 50 1800 typ.
0805
EZJS2VB223 6 12 22000 typ.
EZJS2YC822 18 30 8200 typ.
EZJS2YD472 30 50 4700 typ.
Operating Temperature Range: –40 to 85 °C
Avoid flow soldering
Ratings and Characteristics
Voltage vs. Current
Capacitance vs. Frequency Attenuation vs. Frequency
May. 201906
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 84 –
Current (A)
Zener diode
Zener diode
monopolar 2pcs.
Multilayer Varistor
Capacitor 1 pc.
Voltage (V)
Time (ns)
Voltage (V)
1400
1200
1000
800
600
400
200
0
-200
–20 0 20 40 60 80 100 120 140 160 180 200
Without Varistor
EZJP0V080GA
[V1 mA:8 V, C1 MHz:100 pF max.]
Attenuator : 60 dB
MLCV
150 pF
330 Ω50 Ω
Electrostatic discharger
Oscillo-scope
Mounting area
Approx .83 % space saving
MLCV
Size 0402
Zener diode
S-79
1.5
2.6
0.5
1.7
0.3
MLCC
Size 0402
Varistor Characteristics and Equivalent Circuit
ESD Suppressive Effects
Replacement of Zener diode
A Multilayer Varistor does not have an electrical polarity like zener diodes and is equivalent to total 3 pcs.
of 2 zener diodes and 1 capacitor. [Equivalent Circuit]
[ESD suppressed waveform]
Typical effects of ESD suppression
Test conditions: IEC61000-4-2 Level 4 Contact discharge, 8 kV
Replacing “Zener diode and Capacitor” with Multilayer Varistor saves both the mounting area and number
of components used.
IEC61000-4-2 ··· International Standard of the ESD testing method (HBM) for electronic equipment ability to
withstand ESD generated from a human body. It sets 4 levels of severity
Severity Level 1 Level 2 Level 3 Level 4
Contact discharge 2 kV 4 kV 6 kV 8 kV
Air discharge 2 kV 4 kV 8 kV 15 kV
Dimensions in mm
May. 201906
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 85 –
· Audio lines · LCD/Camera lines
· I/O data lines
IEEE1394 lines
USB1.1/2.0 lines
Mobile Phone
HDMI lines
LCD/Camera
controller
I/O
controller
IEEE1394
controller
USB
controller
· LED
· SW/Keyboard
2 mode noise filter
AMP
IC
IC
TMDS
FPC LCD/Camera
Connector
Connector
Power
IC VDD
GND
TPA+
TPA–
VDD
GND
HDMI
IC
Clock
Ch : 0
Ch : 1
Ch : 2
D+
D–
TPB+
TPB–
Applications Series Circuit
DC 1k 1M 1G (Hz)
Mobile phones, DSC, PC, PDA,
HDD TV (PDP, LC etc.), DVD, DVC,
Game consoles, Audio equipment
Series
EZJZ, P
Ultra low capacitance
(Cap. : 3 pF or less)
DC to GHz
Antenna, RF circuit, LVDS
USB, IEEE1394, HDMI etc.
Low capacitance
(Cap. : 20 to 680 pF)
DC to tens of Hz
PWR, SW, Audio terminals
LCD, RS232C, etc.
PWR, Photoelectronic sensors,
SSR, Motors, Pressure sensors,
Proximity switches
Series
EZJS
High capacitance
(Cap. : 1800 to 22000 pF)
DC to several kHz
PWR, SW, Audio terminals etc.
Applications
Recommended Applications
May. 201906
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 86 –
Performance and Testing Methods
Characteristics Specifi cations Testing Method
Standard test
conditions
Electrical characteristics shall be measured under the following conditions.
Temp. : 5 to 35 °C, Relative humidity : 85 % or less
Varistor voltage To meet the specifi ed
value.
The Varistor voltage is the voltage (VC,or VcmA) between both end terminals of a
Varistor when speci ed current (CmA) is applied to it. The measurement shall be
made as quickly as possible to avoid heating effects.
Maximum
allowable voltage
To meet the specifi ed
value. The maximum DC voltage that can be applied continuously to a varistor.
Capacitance To meet the specifi ed
value.
Capacitance shall be measured at the specifi ed frequency, bias voltage 0 V,
and measuring voltage 0.2 to 2 Vrms.
Maximum peak
current
To meet the specifi ed
value.
The maximum current measured (Varistor voltage tolerance is within ±10 %)
when a standard impulse current of
8/20 µ seconds is applied twice with an interval of 5 minutes.
Maximum ESD To meet the specifi ed
value.
The maximum ESD measured (while the varistor voltage is within ±30 % of its
nominal value) when exposed to ESD 10 times
(fi ve times for each positive-negative polarity) based on IEC61000-4-2.
Solder ability To meet the specifi ed
value.
The part shall be immersed into a soldering bath under the conditions below.
Solder: H63A
Soldering fl ux : Ethanol solution of rosin (Concentration approx. 25 wt%)
Soldering temp. : 230±5 °C
Period : 4±1 s
Soldering position : Immerse both terminal electrodes until they are completely
into the soldering bath.
Resistance to
soldering heat ΔVc / Vc : within ±10 %
After the immersion, leave the part for 24 ±2 hours under the standard condition,
then evaluate its characteristics.Soldering conditions are specifi ed below:
Soldering conditions : 270 °C, 3 s / 260 °C, 10 s
Soldering position : Immerse both terminal electrodes until they are completely
into the soldering bath.
Temperature
cycling ΔVc / Vc : within ±10 %
After repeating the cycles stated below for specified number of times, leave
the part for 24±2 hours, then evaluate its characteristics.
Cycle : 5 cycles
Step Temperature Period
1 Max. Operating Temp. 30±3 min
2 Ordinary temp. 3 min max.
3 Min. Operating Temp. 30±3 min
4 Ordinary temp. 3 min max.
Biased Humidity ΔVc / Vc : within ±10 %
After conducting the test under the conditions specifi ed below, leave the part
24±2 hours, then evaluate its characteristics.
Temp. : 40±2 °C
Humidity : 90 to 95 %RH
Applied voltage : Maximum allowable voltage (Individually specifi ed)
Period : 500+24 / 0 h
High temperature
exposure
(dry heat)
ΔVc / Vc : within ±10 %
After conducting the test under the conditions specifi ed below, leave the part
24 ±2 hours, then evaluate its characteristics.
Temp. : Maximum operating temperature ±3 °C (Individually specifi ed)
Applied voltage : Maximum allowable voltage (Individually specifi ed)
Period : 500+24 / 0h
May. 201906
Panasonic T Ewgmmuummui I juxymymy WMMM 00 T OO 00 Wm'WFF%rfiwm m mw \MLHLHLJLJLHLH T
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 87 –
E
C
D
A
W
1
W
2
B
100 min.
Vacant position
400 min.
Cover tape
160 min.
Vacant position
t1
t2
Feeding hole Chip pocket
Chip component Tape running direction
P1P2P0
F
B
W
E
A
fD0
t2Chip component
Feeding hole Chip pocket
fD0
P1P2P0Tape running direction
EF
W
B
A
t1
Chip component
Feeding hole Chip pocket
Tape running direction
t
P1P2P0
K0
fD0
A
B
F
W
E
Chip component
Feeding hole Chip pocket
Tape running direction
t
1
P
1
P
2
P
0
t
2
fD
0
A
B
F
W
E
Packaging Methods
Series Size Code
(EIA)
Thickness
(mm) Kind of Taping Pitch
(mm)
Quantity
(pcs/reel)
EZJZ
EZJP
Z (0201) 0.3 Pressed Carrier Taping 215,000
0 (0402) 0.5
Punched Carrier Taping
10,000
1 (0603) 0.8
4
4,000
EZJS
1 (0603) 0.8 4,000
2 (0805) 0.8 5,000
1.25 Embossed Carrier Taping 2,000
Reel for Taping
Pitch 2mm (Pressed Carrier Taping) : Size 0201/EIA
(Unit : mm)
Size Code
ABWFEP
1P2P00D0t1t2
21.55
±0.20
2.35
±0.20
8.0
±0.2
3.50
±0.05
1.75
±0.10
4.0
±0.1
2.00
±0.05
4.0
±0.1
1.5
+0.1
0
0.6
max.
1.5
max.
Size Code
(EIA)
ABWFEP
1P2P00D0t1t2
1
(0603) 1.0
±0.1 1.8
±0.1 8.0
±0.2 3.50
±0.05 1.75
±0.10 4.0
±0.1 2.00
±0.05 4.0
±0.1
1.5
+0.1
0
1.1
max. 1.4
max.
2
(0805) 1.65
±0.20 2.4
±0.2
Size Code
ABWFEP
1P2P00D0tK
0
Z0.36
±0.08 0.66
±0.03 8.0
±0.2 3.50
±0.05 1.75
±0.10 2.00
±0.05 2.00
±0.05 4.0
±0.1
1.5
+0.1
0
0.55
max. 0.36
±0.03
(Unit : mm)
(Unit : mm)
Embossed Carrier Taping : Size 0805/EIA
Pitch 4mm (Punched Carrier Taping) :
Size 0603/EIA, 0805/EIA
Leader Part and Taped End
Leader part
Tape end
Dimensions in mm
Pitch 2mm (Punched Carrier Taping) : Size 0402/EIA
(Unit : mm)
(Unit : mm)
Size Code
ABWFEP
1P2P00D0t1t2
00.62
±0.05 1.12
±0.05 8.0
±0.2 3.50
±0.05 1.75
±0.10 2.00
±0.05 2.00
±0.05 4.0
±0.1
1.5
+0.1
0
0.7
max. 1.0
max.
Standard Packing Quantity
ABCDEW
1W2
f180–3 f60.0+1.0 13.0±0.5 21.0±0.8
2.0±0.5 9.0+1.0 11.4±1.0
0
0
0
May. 201906
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 88 –
Handling Precautions
Multilayer Varistors,Chip Type
Series: EZJZ, EZJP (For DC voltage lines, high speed signal lines)
Series: EZJS (For DC voltage lines)
Safety Precautions
Multilayer Varistors (hereafter referred to as “Varistors”) should be used for general purpose applications as
countermeasures against ESD and noise found in consumer electronics (audio/visual, home, office, information &
communication) equipment. When subjected to severe electrical, environmental, and/or mechanical stress beyond the
specifications, as noted in the Ratings and Specified Conditions section, the Varistors’ performance may be degraded,
or become failure mode, such as short circuit mode and open-circuit mode.
If you use under the condition of short-circuit, heat generation of Varistors will occur by running large current due to
application of voltage. There are possibilities of smoke emission, substrate burn-out, and, in the worst case, fire.
For products which require high safety levels, please carefully consider how a single malfunction can affect your
product. In order to ensure the safety in the case of a single malfunction, please design products with fail-safe, such
as setting up protecting circuits, etc.
For the following applications and conditions, please contact us for additional specifications, which is not found
in this document.
· When your application may have difficulty complying with the safety or handling precautions specified below.
· High-quality and high-reliability required devices that have possibility of causing hazardous conditions, such
as death or injury (regardless of directly or indirectly), due to failure or malfunction of the product.
1 Aircraft and Aerospace Equipment (artificial satellite, rocket, etc.)
2 Submarine Equipment (submarine repeating equipment, etc.)
3 Transportation Equipment (motor vehicles, airplanes, trains, ship, traffic signal controllers, etc.)
4
Power Generation Control Equipment (atomic power, hydroelectric power, thermal power plant control system, etc.)
5 Medical Equipment (life-support equipment, pacemakers, dialysis controllers, etc.)
6 Information Processing Equipment (large scale computer systems, etc.)
7 Electric Heating Appliances, Combustion devices (gas fan heaters, oil fan heaters, etc.)
8 Rotary Motion Equipment
9 Security Systems
J And any similar types of equipment
Strict Observance
1. Confirmation of Rated Performance
The Varistors shall be operated within the specified rating/performance.
Applications exceeding the specifications may cause deteriorated performance and/or breakdown, resulting in
degradation and/or smoking or ignition of products. The following are strictly observed.
(1) The Varistors shall not be operated beyond the specified operating temperature range.
(2) The Varistors shall not be operated in excess of the specified maximum allowable voltage.
(3) The Varistors shall not be operated in the circuits to which surge current and ESD that exceeds the specified
maximum peak current and maximum ESD.
(4) Never use for AC power supply circuits.
2. The Varistors shall not be mounted near flammables.
1. Circuit Design
1.1
Operating Temperature and Storage Temperature
When operating a components-mounted circuit,
please be sure to observe the “Operating
Temperature Range”, written in delivery
specifications. Storage temperature of PCB after
mounting Varistors, which is not operated, should be
within the specified “Storage Temperature Range” in
the delivery specifications. Please remember not to
use the product under the condition that exceeds
the specified maximum temperature.
1.2 Operating Voltage
The Varistors shall not be operated in excess of
the “Maximum allowable voltage”. If the Varistors
are operated beyond the specified Maximum
allowable voltage, it may cause short and/or
damage due to thermal run away.
The circuit that continuously applies high
frequency and/or steep pulse voltage please
examines the reliability of the Varistor even if it is
used within a “Maximum allowable voltage”. Also,
it would be safer to check also the safety and
reliability of your circuit.
Operating Conditions and Circuit Design
May. 201903
Panasonic / ”fifi—m W L ‘ A ‘2 L1 Rel yyyyy \k if ‘5‘ %%%
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 89 –
Land
SMD
ab
c
Solder resist
(a) Excessive amount (b) Proper amount (c) Insufficient amount
Solder resist
Land
Portion to be
Excessively soldered
A lead wire of
Retrofitted
component
Soldering
iron
Solder
(ground solder)
Chassis
Electrode pattern
Solder resist
Solder resist
Solder resist
The lead wire of a
Component With lead wires
1.3 Self-heating
The surface temperature of the Varistors shall
be under the specified Maximum Operating
Temperature in the Specifications including the
temperature rise caused by self-heating. Check
the temperature rise of the Varistor in your circuit.
1.4 Environmental Restrictions
The Varistors shall not be operated and/or stored
under the following conditions.
(1) Environmental conditions
(a) Under direct exposure to water or salt water
(b) Under conditions where water can condense
and/or dew can form
(c) Under conditions containing corrosive gases
such as hydrogen sulfide, sulfurous acid,
chlorine and ammonia
(2) Mechanical conditions
The place where vibration or impact that
exceeds specified conditions written in
delivery specification is loaded.
2. Design of Printed Circuit Board
2.1 Selection of Printed Circuit Boards
There is a possibility of performance deterioration
by heat shock (temperature cycles), which causes
cracks, from alumina substrate.
Please confirm that the substrate you use does
not deteriorate the Varistors’ quality.
2.2 Design of Land Pattern
(1) Recommended land dimensions are shown below.
Use the proper amount of solder in order to
prevent cracking. Using too much solder places
excessive stress on the Varistors.
Recommended Land Dimensions
Unit (mm)
Size Code
(EIA)
Component dimensions abc
LW T
Z(0201)
0.6 0.3 0.3 0.2 to 0.3
0.25 to 0.30
0.2 to 0.3
0(0402)
1.0 0.5 0.5 0.4 to 0.5 0.4 to 0.5 0.4 to 0.5
1(0603)
1.6 0.8 0.8 0.8 to 1.0 0.6 to 0.8 0.6 to 0.8
2(0805)
2.0 1.25 0.8 to 1.25 0.8 to 1.2 0.8 to 1.0 0.8 to 1.0
(2) The land size shall be designed to have equal
space, on both right and left side. If the amount
of solder on the right land is different from that
of the left land, the component may be cracked
by stress since the side with a larger amount of
solder solidifies later during cooling.
Recommended Amount of Solder
2.3 Utilization of Solder Resist
(1) Solder resist shall be utilized to equalize the
amounts of solder on both sides.
(2) Solder resist shall be used to divide the pattern
for the following cases;
· Components are arranged closely.
· The Varistor is mounted near a component
with lead wires.
· The Varistor is placed near a chassis.
See the table below.
Prohibited Applications and Recommended Applications
Item Prohibited
applications
Improved applications
by pattern division
Mixed mounting
with a component
with lead wires
Arrangement near
chassis
Retro-fi tting of
component with
lead wires
Lateral
arrangement
2.4 Component Layout
To prevent the crack of Varistors, place it on the
position that could not easily be affected by the
bending stress of substrate while going through
procedures after mounting or handling.
(1) To minimize mechanical stress caused by the
warp or bending of a PC board, please follow
the recommended Varistors’ layout below.
Prohibited layout Recommended layout
Layout the Varistors sideways
against the stressing direction.
May. 201903
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 90 –
AB
C
E
D
Slit
Magnitude of stress A>B=C>D>E
Perforation
Supporting
pin
Supporting
pin
Crack
Separation of solder
Crack
(2) The following layout is for your reference since
mechanical stress near the dividing/breaking
position of a PC board varies depending on
the mounting position of the Varistors.
(3) The magnitude of mechanical stress applied
to the Varistors when dividing the circuit board
in descending order is as follows: push back
< slit < V-groove < perforation. Also take into
account the layout of the Varistors and the
dividing/breaking method.
2.5 Mounting Density and Spaces
Intervals between components should not be too
narrow to prevent the influence from solder bridges
and solder balls. The space between components
should be carefully determined.
1. Storage
(1) The Varistors shall be stored between 5 to
40 °C and 20 to 70 % RH, not under severe
conditions of high temperature and humidity.
(2) If stored in a place where humidity, dust, or
corrosive gasses (hydrogen sulfide, sulfurous
acid, hydrogen chloride and ammonia, etc.) are
contained, the solderability of terminals electrodes
will be deteriorated.
In addition, storage in a place where the heat
or direct sunlight exposure occurs will causes
mounting problems due to deformation of tapes
and reels and components and taping/reels
sticking together.
(3) Do not store components longer than 6 months.
Check the solderability of products that have
been stored for more than 6 months before use.
2. Adhesives for Mounting
(1) The amount and viscosity of an adhesive for
mounting shall be such that the adhesive will
not flow off on the land during its curing.
(2) If the amount of adhesive is insufficient for
mounting, the Varistors may fall off after or
during soldering.
(3) L o w -v i scosity of the adhesive causes
displacement of Varistors.
(4) The heat-curing methods for adhesive are
ultraviolet radiation, far-infrared radiation, and so
on. In order to prevent the terminal electrodes of
the Varistors from oxidizing, the curing shall be
under the following conditions:
160 °C max., for 2 minutes max.
(5) Insufficient curing may cause the Varistors to fall
off after or during soldering. In addition, insulation
resistance between terminal electrodes may
deteriorate due to moisture absorption. In
order to prevent these problems, please
observe proper curing conditions.
3. Chip Mounting Consideration
(1) When mounting the Varistors components on a
PC board, the Varistor bodies shall be free from
excessive impact loads such as mechanical
impact or stress due to the positioning, pushing
force and displacement of vacuum nozzles
during mounting.
(2) Maintenance and inspection of the Chip Mounter
must be performed regularly.
(3) If the bottom dead center of the vacuum nozzle
is too low, the Varistor will crack from excessive
force during mounting.
Pease refer to the following precautions and
recommendations.
(a) Set and adjust the bottom dead center of
the vacuum nozzles to the upper surface of
the PC board after correcting the warp of
the PC board.
(b) Set the pushing force of the vacuum nozzle
during mounting to 1 to 3 N in static load.
(c) For double surface mounting, apply a
supporting pin on the rear surface of the
PC board to suppress the bending of the
PC board in order to minimize the impact of
the vacuum nozzles. Typical examples are
shown in the table below.
(d) Adjust the vacuum nozzles so that their
bottom dead center during mounting is not
too low.
Item Prohibited mounting
Recommended mounting
Single surface
mounting
The supporting pin does not necessarily
have to be positioned beneath the
Varistor.
Double surface
mounting
Precautions for Assembly
May. 201903
Panasonic ® @
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 91 –
260
240
0
Temperature(˚C)
Time
3 to 5 s
Soldering
T
Gradual cooling
(at ordinary mperature)
60 to 120 s
Gradual
cooling
5
Heating3
Peak4
Temp. rise
T
2
Preheating1
260
220
180
140
Temperature (˚C)
Time
60 to 120 s 60 s max.
(4) The closing dimensions of the positioning
chucks shall be controlled. Maintenance and
replacement of positioning chucks shall be
performed regularly to prevent chipping or
cracking of the Varistors caused by mechanical
impact during positioning due to worn
positioning chucks.
(5) Maximum stroke of the nozzle shall be adjusted
so that the maximum bending of PC board
does not exceed 0.5 mm at 90 mm span. The
PC board shall be supported by an adequate
number of supporting pins.
4. Selection of Soldering Flux
Soldering flux may seriously affect the performance
of the Varistors. Please confirm enough whether the
soldering flux have an influence on performance of the
Varistors or not, before using.
5. Soldering
5.1 Flow Soldering
When conducting flow soldering, stress from abrupt
temperature change is applied to the Varistors, so the
temperature, especially temperature of solder should
be controlled very carefully. Varistors should not be
subjected to abrupt temperature change because it
causes occurrence of thermal cracks as a result of
excessive thermal stress inside of the Varistors from
flow soldering. You should be careful to temperature
difference. Therefore it is essential that soldering
process follow these recommended conditions.
(1) Application of Soldering flux :
The soldering flux shall be applied to the
mounted Varistors thinly and uniformly by foaming
method.
(2) Preheating :
Conduct sufficient pre-heating, and make sure
that the temperature difference between solder
and Varistors’ surface is 150 °C or less.
(3) Immersion into Soldering bath :
The Varistors shall be immersed into a soldering
bath of 240 to 260 °C for 3 to 5 seconds.
(4) Gradual Cooling :
After soldering, avoid rapid cooling (forced
cooling) and conduct gradual cooling, so that
thermal cracks do not occur.
(5) Flux Cleaning :
When the Varistors are immersed into a cleaning
solvent, be sure that the surface temperatures of
devices do not exceed 100 °C.
(6) Performing flow soldering once under the
conditions shown in the figure on the right
“Recommended profile of Flow soldering (Ex.)”
will not cause any problems. However, pay
attention to the possible warp and bending of the
PC board.
5.2 Reflow Soldering
The reflow soldering temperature conditions are
composed of temperature curves of Preheating,
Temp. rise, Heating, Peak and Gradual cooling.
Large temperature difference inside the Varistors
caused by rapid heat application to the Varistors
may lead to excessive thermal stresses, contributing
to the thermal cracks. The Preheating temperature
requires controlling with great care so that
tombstone phenomenon may be prevented.
Item Temperature Period or Speed
1 Preheating 140 to 180 °C 60 to 120 s
2 Temp. rise Preheating temp
to Peak temp. 2 to 5 °C /s
3 Heating 220 °C min. 60 s max.
4 Peak 260 °C max. 10 s max.
5 Gradual cooling Peak temp.
to 140 °C 1 to 4 °C /s
Recommended profi le of Refl ow soldering (EX.)
Recommended profi le of Flow soldering (Ex.)
T : Allowable temperature difference T < 150 °C
<Allowable temperature difference>
The rapid cooling (forced cooling) during Gradual
cooling part should be avoided, because this may
cause defects such as the thermal cracks, etc.
When the Varistors are immersed into a cleaning
solvent, make sure that the surface temperatures of
the devices do not exceed 100 °C.
Performing reflow soldering twice under the
conditions shown in the figure above “Recommended
profile of Reflow soldering (Ex.)” will not cause any
problems. However, pay attention to the possible
warp and bending of the PC board.
For products specified in individual specifications,
avoid flow soldering.
Size Temp. Tol.
0603/EIA T < 150 °C
May. 201903
Panasonic
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 92 –
T
Preheating
60 to 120 s 3 s max.
Gradual cooling
Supporting pin
Separated, Crack
Check pin
Check pin
5.3 Hand Soldering
Hand soldering typically causes significant
temperature change, which may induce excessive
thermal stresses inside the Varistors, resulting in
the thermal cracks, etc.
In order to prevent any defects, the following
should be observed.
· Control the temperature of the soldering tips
with special care.
· Avoid the direct contact of soldering tips with
the Varistors and/or terminal electrodes.
· Do not reuse dismounted Varistors.
(1) Condition 1 (with preheating)
(a) Soldering :
Use thread solder (01 mm or below) which
contains flux with low chlorine, developed
for precision electronic equipment.
(b) Preheating :
Conduct sufficient Preheating, and make
sure that the temperature difference
between solder and Varistors’ surface is
150 °C or less.
(c) Temperature of Iron tip: 300 °C max.
(The required amount of solder shall be
melted in advance on the soldering tip.)
(d) Gradual cooling :
After soldering, the Varistors shall be
cooled gradually at room temperature.
Recommended profi le of Hand soldering (Ex.)
(2) Condition 2 (without preheating)
Hand soldering can be performed without
preheating, by following the conditions below:
(a) Soldering iron tip shall never directly touch
the ceramic and terminal electrodes of the
Varistors.
(b) The lands are sufficiently preheated
with a soldering iron tip before sliding
the soldering iron tip to the terminal
electrodes of the Varistors for soldering.
Conditions of Hand soldering without preheating
Item Condition
Temperature of Iron tip 270 °C max.
Wattage 20 W max.
Shape of Iron tip 03 mm max.
Soldering time with a soldering iron 3 s max.
6. Post Soldering Cleaning
6.1 Cleaning solvent
Soldering flux residue may remain on the PC
board if cleaned with an inappropriate solvent.
This may deteriorate the performance of Varistors,
especially insulation resistance.
6.2 Cleaning conditions
Inappropriate cleaning conditions such as
insufficient cleaning or excessive cleaning may
impair the electrical characteristics and reliability
of the Varistors.
(1) Insufficient cleaning can lead to :
(a) The halogen substance found in the residue
of the soldering flux may cause the metal of
terminal electrodes to corrode.
(b) The halogen substance found in the residue
of the soldering flux on the surface of the
Varistors may change resistance values.
(c) Water-soluble soldering flux may have more
remarkable tendencies of (a) and (b) above
compared to those of rosin soldering flux.
(2) Excessive cleaning can lead to :
(a) When using ultrasonic cleaner, make sure
that the output is not too large, so that the
substrate will not resonate. The resonation
causes the cracks in Varistors and/or
solders, and deteriorates the strength of the
terminal electrodes.
Please follow these conditions for Ultrasonic
cleaning:
Ultrasonic wave output : 20 W/L max.
Ultrasonic wave frequency : 40 kHz max.
Ultrasonic wave cleaning time : 5 min. max.
6.3 Contamination of Cleaning solvent
Cleaning with contaminated cleaning solvent may
cause the same results as that of insufficient cleaning
due to the high density of liberated halogen.
7. Inspection Process
The pressure from measuring terminal pins might
bend the PCB when implementing circuit inspection
after mounting Varistors on PCB, and as a result,
cracking may occur.
(1) Mounted PC boards shall be supported by an
adequate number of supporting pins on the back
with bend settings of 90 mm span 0.5 mm max.
(2) Confirm that the measuring pins have the right
tip shape, are equal in height, have the right
pressure and are set in the correct positions.
The following figures are for your reference to
avoid bending the PC board.
T : Allowable temperature difference T<150 °C
Prohibited setting Recommended setting
Bending of
PC board
May. 201903
Panasonic WW
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Multilayer Varistors
– 93 –
Bending Torsion
PC board
splitting jig
V-groove
PC board
Outline of Jig
PC
board
Chip
component
Loading
point
V-groove
Loading direction
PC
board
Chip component
Loading
point
V-groove
Loading direction
Floor
Crack
Mounted PCB
Crack
8. Protective Coating
When the surface of a PC board on which the
Varistors have been mounted is coated with resin
to protect against moisture and dust, it shall be
confirmed that the protective coating does not affect
the performance of Varistors.
(1) Choose the material that does not emit the
decomposition and/or reaction gas. The Gas may
affect the composing members of the Varistors.
(2) Shrinkage and expansion of resin coating when
curing may apply stress to the Varistors and may
lead to occurrence of cracks.
9. Dividing/Breaking of PC Boards
(1) Please be careful not to stress the substrate with
bending/twisting when dividing, after mounting
components including Varistors. Abnormal and
excessive mechanical stress such as bending or
torsion shown below can cause cracking in the
Varistors.
(2) Dividing/Breaking of the PC boards shall be
done carefully at moderate speed by using a
jig or apparatus to prevent the Varistors on the
boards from mechanical damage.
(3) Examples of PCB dividing/breaking jigs:
The outline of PC board breaking jig is shown
below. When PC board are broken or divided,
loading points should be close to the jig to
minimize the extent of the bending.
Also, planes with no parts mounted on should
be used as plane of loading, in order to prevent
tensile stress induced by the bending, which
may cause cracks of the Varistors or other parts
mounted on the PC boards.
Prohibited dividing Recommended dividing
10. Mechanical Impact
(1) The Varistors shall be free from any excessive
mechanical impact. The Varistor body is made
of ceramics and may be damaged or cracked if
dropped. Never use a Varistor which has been
dropped; their quality may already be impaired