0687980002 Spec Datasheet by Molex

View All Related Products | Download PDF Datasheet
TD USB Type C to Type C Pluq 2.0 cable assv
Title:
USB Type C to Type C Plug 2.0 cable assy
TITLE :
THIS DOCUMENT CONTAINS INFORMATIOON THAT IS PROPRIETARY TO
MOLEX AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DOCUMENT NO.
Prepared By : LUCY LI Date : Sheet No.
Checked By : LUCY LI Date :
Approved By : NIE FRED Date :
REV.
PS-68798-0004
15/03/11
15/03/11
15/03/11
DONGGUAN MOLEX INTERCONNECT.,LTD
PRODUCT SPECIFICATION
USB Type C to Type C Plug 2.0 cable assy
1 OF 7
A Initial Release
DESCRIPTION
1 Scope
This specification covers the requirements for the Standard Type C to Type C Plug 2.0 cable assembly
2 Product Description
USB Type C to Type C Plug 2.0 cable assy
See the sales drawing and the other section of this specification for the necessary.In cases where the specification
differs from the drawings, the sales drawings take precedence.
3 Ratings
Voltage
Rated Voltage: 30V DC
Current
Vbus and GND, refer to the sales drawing
Current of 0.25A shall be applied to all the other contacts.
4 Temperature
Operating temperature: -10 °C to +50 °C
Storage temperature: -20 °C to +60 °C
5. Pin assignment
See sales drawing
TITLE :
THIS DOCUMENT CONTAINS INFORMATIOON THAT IS PROPRIETARY TO
MOLEX AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DOCUMENT NO.
Prepared By : LUCY LI Date : Sheet No.
Checked By : LUCY LI Date :
Approved By : NIE FRED Date :
A Initial Release
REV.
DESCRIPTION
PS-68798-0004
15/03/11
15/03/11
15/03/11 2 OF 7
DONGGUAN MOLEX INTERCONNECT.,LTD
USB Type C to Type C Plug 2.0 cable assy
TITLE :
THIS DOCUMENT CONTAINS INFORMATIOON THAT IS PROPRIETARY TO
MOLEX AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DOCUMENT NO.
Prepared By : LUCY LI Date : Sheet No.
Checked By : LUCY LI Date :
Approved By : NIE FRED Date :
Cable
Assembly
Voltage Drop
PS-68798-0004
15/03/11
15/03/11 3 OF7
USB Type C to Type C Plug 2.0 cable assy
6. Electrical And Signal Integrity Compliance Requirements
DONGGUAN MOLEX INTERCONNECT.,LTD
Test
Description Test Condition Performance Requirement
250 mV max for GND and 500 mV max for VBUS.
REV.
DESCRIPTION
Dielectric
Withstanding
Voltage Test voltage 100 VAC, 1Min. No breakdown
The maximum rated VBUS current of the cable
assembly shall be used.
The measurement includes representative
receptacles at both ends of the cable assembly,
mounted on test fixtures.
15/03/11
A Initial Release
Low Level
Contact
Resistance
(LLCR)
EIA 364-23
The low level contact resistance (LLCR)
measurement is made across the plug and
receptacle mated contacts and does not include
any internal paddle cards or substrates of the
plug or receptacle. The test boards shall be
provided with the connectors to be tested.
• Measure at 20 mV (max) open circuit at 100
mA.
The following requirements apply to the power and
signal contacts:
• 40 m (max) initial for VBUS, GND and all other
contacts.
• 50 m maximum after initial measurement.
TITLE :
THIS DOCUMENT CONTAINS INFORMATIOON THAT IS PROPRIETARY TO
MOLEX AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DOCUMENT NO.
Prepared By : LUCY LI Date : Sheet No.
Checked By : LUCY LI Date :
Approved By : NIE FRED Date :
Differential
coupling
between
CC and USB
D+/D-
Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document
Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document
Differential
coupling
between
VBUS and
USB D+/D-
Single-ended
coupling
between
SBU_A and
CC, SBU_B
and CC
Single end
coupling
between CC
and D-
Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document
DESCRIPTION
PS-68798-0004
For cable assemblies the limit is defined with the
vertices of (0.3 MHz, -60.5 dB), (1 MHz, −50 dB),
(10 MHz, −30 dB), (16 MHz, −26 dB) and (100
MHz, −26 dB) on scale of log10(f) .
-40 dB for 0.3 MHz < f 30 MHz, and
19.12·log10(f/30)-40 (in dB) for 30 MHz< f
100 MHz..
Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document
Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document
Single- ended
coupling
between
SBU_A and
SBU_B
The limit is defined with the vertices of (0.3 MHz, -
65 dB), (1 MHz, −55 dB), (18 MHz, −30 dB), and
(100 MHz, −30 dB) on scale of log10(f).
The limit is defined with the vertices of (0.3 MHz,
−56.5 dB), (1 MHz, −46 dB), (10 MHz, −26 dB),
(11.2 MHz, −25 dB), and (100 MHz, −25 dB) on
scale of log10(f).
0.3MHz, -48.5dB
1MHz, -38dB
10MHz, -18dB;
100MHz,-18dB
REV.
15/03/11 4 OF7
15/03/11
USB Type C to Type C Plug 2.0 cable assy
Test Procedure
15/03/11
DONGGUAN MOLEX INTERCONNECT.,LTD
Performance Requirement
Test
Description
A Initial Release
TITLE :
THIS DOCUMENT CONTAINS INFORMATIOON THAT IS PROPRIETARY TO
MOLEX AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DOCUMENT NO.
Prepared By : LUCY LI Date : Sheet No.
Checked By : LUCY LI Date :
Approved By : NIE FRED Date :
D+/D- Pair
Differential
Impedance
Refer to appendix G.4 of Type C connectors and
cable assemblies compliance document
Measured with a 400 ps rise time (20%-80%)
VBUS loop
inductance Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document 900 nH
0.3MHz, -80dB
30MHz, -40dB
100MHz, -40dB
75 ohms min and 105 ohms max
Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document
Inductance
Coupling
Factor (k)
between
VBUS and
Other Low
Speed Signals
(CC, SBU_A,
SBU_B, D+,
and D-)
Refer to appendix G.4 of Type C connectors and
cable assemblies compliance document
0.3. The inductance coupling factor is defined
as the ratio of mutual inductance to the square root
of the product of the loop inductances of the two
coupled lines. For example, the coupling factor
between VBUS and CC is:
k=L_(VBUS_CC)/(L_VBUS L_CC )
Refer to appendix G.4 of Type C connectors and
cable assemblies compliance document
Measured with a 400 ps rise time (20%-80%) at
50% voltage crossing..
A Initial Release
D+/D- Pair
intra-pair Skew
D+/D- Pair
Attenuation
USB Type C to Type C Plug 2.0 cable assy
DESCRIPTION
15/03/11
15/03/11
100 ps max.
REV.
15/03/11
5 OF 7
D+/D- Pair
Propagation
Delay
Performance Requirement
−1.02 dB @ 50 MHz
−1.43 dB @ 100 MHz
−2.40 dB @ 200 MHz
−4.35 dB @ 400 MHz
Refer to appendix G.4 of Type C connectors and
cable assemblies compliance document
Measured with a 400 ps rise time (20%-80%) at
50% voltage crossing.
Differential
coupling
between
SBU_A/SBU_
B and USB
D+/D−
DONGGUAN MOLEX INTERCONNECT.,LTD
20 ns max.
Refer to appendix G.5 of Type C connectors and
cable assemblies compliance document
Test
Description Test Procedure
PS-68798-0004
TITLE :
THIS DOCUMENT CONTAINS INFORMATIOON THAT IS PROPRIETARY TO
MOLEX AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DOCUMENT NO.
Prepared By : LUCY LI Date : Sheet No.
Checked By : LUCY LI Date :
Approved By : NIE FRED Date :
Test Procedure
7. Mechanical Compliance Requirements
Performance Requirement
REV.
A
15/03/11
Test
Description
Wrenching
Strength
(Plug-only)
PS-68798-0004
Insertion Force EIA 364-13
The insertion force test shall be done at a
maximum rate of 12.5 mm (0.492") per minute.
DESCRIPTION
Within the range from 5 N to 20 N.
USB Type C to Type C Plug 2.0 cable assy
DONGGUAN MOLEX INTERCONNECT.,LTD
4-Axes
Continuity
6 OF 7
EIA 364-38 Test Condition A
The cable assembly shall is subjected to a 40N
axial load for a minimum of 1 minute
while clamping one end of the cable plug.
Cable Pull-Out No visible physical damage and no electrical
discontinuity over 1 microsecond to the cable
assembly.
15/03/11
Perpendicular forces are applied to the plug in
four directions (i.e., left, right, up, and down).
A metal fixture with opening and tongue
representative of a receptacle shall be used.
Refer to Appendix E of Type C connectors and
cable assemblies compliance document
Refer to appendix D of Type C connectors and
cable assemblies compliance document.
Plug and Receptacle: Subject the mating
interface to the moments defined in Appendix D
for at least 10 seconds.
No discontinuities greater than 1 microsecond
duration in any of the four orientations tested.
EIA 364-41, Condition I with Dimension X =
3.7 times the cable diameter and 100 cycles
in each of two planes 120 degree arc.
No physical damage and discontinuity over
1 microsecond during flexing shall occur to the
cable assembly
15/03/11
Initial Release
A single plug shall be used for this test. Some
mechanical deformation may occur. The plug shall
be mated with the continuity test fixture after the
test forces have been applied to verify no damage
has occurred that causes discontinuity or shorting.
The Dielectric Withstanding Voltage test shall be
conducted after the continuity test to verify plug
compliance.
A new plug is required for each of the four test
directions. The plug shall disengage from the test
fixture or demonstrate mechanical failure (i.e., the
force applied during the test procedure peaks and
drops off) when a moment of 2.0 Nm is applied to
the plug in the up and down directions and a
moment 3.5 Nm is applied to the plug in the left
and right directions.
Cable Flexing
at 80%:3%
TITLE :
THIS DOCUMENT CONTAINS INFORMATIOON THAT IS PROPRIETARY TO
MOLEX AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
DOCUMENT NO.
Prepared By : LUCY LI Date : Sheet No.
Checked By : LUCY LI Date :
Approved By : NIE FRED Date :
8. Environmental Compliance Requirements
Subject samples to between 25±3 at 80%±3%
RH and 65±3 at 50%±3% RH,Ramp times
should be 0.5 hour and dwell times should be
1.0hour.Dwell times start when the temperature
and humidity have stabilized within the specified
levels.Perform 24 such cycles.
Conductor resistance meets spec before and after
the Cyclic Temperature and Humidity test.
10,000 cycles minimum.
Conductor resistance and dielectric withstanding
voltage shall be checked to be within spec after
the 10,000 durability cycles
Within the range of 8 N to 20 N, measured after a
preconditioning of five insertion/extraction cycles
(i.e., the sixth extraction). After an additional
twenty-five insertion/extraction cycles, the
extraction force shall be measured again (i.e., the
thirty-second extraction) and the extraction force
shall be within:
a) 33 % of the initial reading, and
b) within the range of 8 N to 20 N.
The extraction force shall be within the range of 6
N to 20 N after 10,000 insertion/extraction cycles.
This requirement does not apply to the plugs that
are used for direct docking without a cable.
Performance Requirement
EIA 364-09
EIA 364-13
The extraction force test shall be done at a
maximum rate of 12.5 mm (0.492") per minute.
Test
Description
15/03/11
USB Type C to Type C Plug 2.0 cable assy
PS-68798-0004
7 OF 7
A Initial Release
REV.
DESCRIPTION
15/03/11
15/03/11
DONGGUAN MOLEX INTERCONNECT.,LTD
Cyclic
Temperature
and Humidity
EIA 364-31
The object of this test procedure is to detail a
standard test method for the evaluation of the
designs and materials used in USB connectors
as the effects of high humidity and heat
influences them.
Temperature
Life
EIA 364-17, Method A.
105º C without applied voltage for 120 hours.
105º C without applied voltage for 72 hours
when used as preconditioning.
The object of this test procedure is to detail a
standard method to assess the ability of a USB
connector to withstand temperature.
Durability or
Insertion/Extra
ction
Cycles
Test Procedure
Conductor resistance meets spec before and after
theTemperature Life test.
Extraction
Force
Test
Description Test Procedure Performance Requirement

Products related to this Datasheet

UNIVERSAL SERIAL BUS (USB) SHIEL