ADIS16IMU1/PCBZ Wiki-Guide Datasheet by Analog Devices Inc.

View All Related Products | Download PDF Datasheet
ANALOG DEVICES
One Technology Way · P.O. Box 9106 · Norwood, MA 02062-9106 · Tel: 781.329.4700 · Fax: 781.461.3113 · www.analog.com
Rev 25 Jun 2013 19:50 | Page 1
ADIS16IMU1/PCBZ Breakout Board
Wiki-Guide
OVERVIEW
The ADIS1613x, ADIS1636x, ADIS16375, ADIS16407 and ADIS1648x IMU products all use a 24-pin,
dual-row, 1mm connector for their electrical interface. This mating connector for their interface
supports surface-mount solder attachment but does not support direct attachment with ribbon cables.
For those who are would like to connect to these IMU/gyroscope products to an existing processor
board, using a ribbon cable, the ADIS16IMU1/PCBZ provides a simple connector translation for this
purpose.
Here is a picture of the contents that come with the ADIS16IMU1/PCBZ.
IMU/GYROSCOPE MOUNTING HOLES
The ADIS16IMU1/PCBZ provides several sets of mounting holes that line up with mounting holes and
tabs on the following products: ADIS1613x, ADIS1636x, ADIS16375, ADIS1640x and ADIS1648x
products. Please see the following picture for device mounting hole locations.
1.65mm D < a="" '="" '="" ”mm“:="" ise"s°r®="" e="" e="" g="" s="" ‘6="" fl="" ‘d="" vi="" '0="" e="" s="" 3="" i="" do="" not="" use="" wnh="" amswm="" m1="" imu="" interface="" board="" _‘="" ‘="" gsibwei’e="" v="" l="" ml/eel="" 7129/“="" —‘="">< 635m="" 58,42!!!"="" —’="" 64="" 77mm="">
Rev 25 Jun 2013 19:50 | Page 2
ADIS16133, ADIS16135, ADIS1636 Mounting
Use the M2x0.4x16mm machine screws (provided in pink bag) for mounting these products to the
ADIS16IMU1/PCBZ and set their torque for 20 inch-ounces. The yellow-highlights in the top-view
picture illustrate the location of the mounting holes for these products.
Rev 25 Jun 2013 19:50 | Page 3
ADIS16360, ADIS16362, ADIS16364, ADIS16365, ADIS16367,
ADIS16400, ADIS16405, ADIS16407 Mounting
Use the M2x0.4x4mm machine screws (provided in pink bag) for mounting these products to the
ADIS16IMU1/PCBZ and set their torque for 20 inch-ounces. The pink-highlights in the top-view picture
illustrate the location of the mounting holes for these products. For high-vibration environments,
consider using more than 2 screws, per AN-1045
ADIS16375, ADIS16480, ADIS16485, ADIS16488 Mounting
Use the M2x0.4x16mm machine screws (provided in pink bag) for mounting these products to the
ADIS16IMU1/PCBZ and set their torque for 20 inch-ounces. The blue-highlights in the top-view picture
illustrate the location of the mounting holes for these products. Here is an example of the
ADIS16IMU1/PCBZ, with an ADIS16485AMLZ mounted to it.
Make sure that the connector pins are in alignment with J2 on the ADIS16IMU1/PCBZ, before pressing
it into place.
Here is a close-up view, which shows the correct connector alignment.
Rev 25 Jun 2013 19:50 | Page 4
This picture provides an example of the an incorrect connector alignment. Note that this view is
on the EVAL-ADISZ board, not the ADIS16IMU1/PCBZ.
INTERFACE CONNECTOR
J1 is the electrical connector that provides direct access to power, ground and critical digital I/O pins
on the devices. It is a 16-pin, dual-row, 2-mm pitch connector that support 1mm ribbon cable systems.
Pin Assignments
Here is the pin assignments for J1, which is the connector that will interface with an embedded
processor board.
mm H was Not installad -——- mm
Rev 25 Jun 2013 19:50 | Page 5
Ribbon Cable Options
Check out the following link for ideas on how to make or purchase 16-pin, 1mm ribbon cables that can
mate to J1 on the ADIS16IMU1/PCBZ.
Acquiring 1mm ribbon cables
ELECTRICAL SCHEMATIC
ANALOG DEVICES
Rev 25 Jun 2013 19:50 | Page 6
© Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners. www.analog.com

Products related to this Datasheet

BREAKOUT IMU INTERFACE BOARD