USD

Accessories Catalog (2017)

Fluke Electronics

View All Related Products | Download PDF Datasheet

Datasheet

Accessories
Catalog
2017 edition
Expand the capabilities
of your test tools
Fluke CAMO-C25 Camouflage
Carrying Case
The CAMO-C25 Camouflage
Carrying Case is a durable,
zippered carrying case with pad-
ding and inside pocket, and
high quality polyester exterior. It
includes a convenient hand strap
and carries most of Fluke’s popular
digital multimeters. It is available
in trendy camouflage.
Fluke AC288 Terminal
Block Probe
The AC288 Terminal Block Probe
features a retractable probe tip
that provides safe and secure
connections to clamp and screw
type terminal blocks. Designed for
increased safety, while providing
flexibility to reach deep connec-
tion points.
Fluke CXT1000
Extreme Hard Case
The hard case that is designed for
maximum protection and fits all
your Fluke test tools and acces-
sories. Configure the diced foam
interior to store, protect, and
carry your test tools. Waterproof
and airtight, built to withstand
the most extreme conditions.
Fluke Connect® ir3000 FC
Connector
Wirelessly transfer data from your
existing Fluke tools to your smart
phone. Graph, save and share
the tool’s measurements straight
from the field to the team.
You’ve already invested in a Fluke test and
measurement tool. Now expand its capabilities with
Fluke genuine accessories.
A digital multimeter can become a thermometer, an
amp-meter, or even a pressure gauge.
Cases protect your tools. Non-contact detectors,
probes and hat lights, meter hangers and appropriately
rated test probes improve your safety and your
proficiency.
Did you know?
New! Category ratings, safety standards: Test leads, probes, clips.
IEC 61010-031 covers safety requirements for handheld probe assemblies for
electrical measurement and test. Recent updates require that the following
changes be made to all test leads, probes and clips:
Test lead wire must contain an inner layer wear indicator which allows for
increased safety.
Test probes used in CAT III and CAT IV measurement environments must be
fully insulated and only allow a maximum of 4 mm of exposed metal at the
probe tip. Older probe tips that had 19 mm (.75 in) of exposed metal must
now be capped to allow only 4 mm of tip exposure if used in a high energy
environment.
Test probes with more than 4 mm of exposed metal at the probe tip can be
used in CAT II measurements.
Alligator clips must contain jaws which are fully insulated with no exposed
metal accessible by a user’s fingers.
For more information on CAT ratings and choosing the best test probe for your job, see the “Electrical measurement category
ratings for test tools” chart on page 11 of this catalog.
Table of contents
CURRENT INPUT
CURSOR
SCOPE
OFF
HARMONICS
POWER EVENTS
METER
V A Hz
ENTER
MAX 30V
SAVE
SCREEN
ESC
MENU
VOLTAGE INPUT
HOLD
RUN
RECORD
MEASURE
600V
CAT
Test leads 4
Test lead sets and kits 12
Temperature accessories 16
Current clamps 20
Cases, holsters and hangers 28
Vibration 35
Lights 36
Infrared cameras 38
Portable oscilloscopes 40
Specialty probes 42
Software 43
Automotive 44
Specialty products 46
Power quality 48
Process tools 51
CarePlans 52
Index 53
36 38
35
16
12
4
28
20
43
52
42
51
40
484644
4
Test leads
Model number TL175 TL26A TL40 TL71 TL75 TL76 TL221 TL222 TL224 TL910
10/11/12/12B • • • • • • • • •
110/111/112 • • • • • • • • •
114/115/116/117 • • • • • • • • •
20/70 Series • • • • • • • • •
27 • • • • • • • • •
70/73 III • • • • • • • • •
175/177/179 • • • • • • • • •
80 Series III/83V • • • • • • • • •
87/89 IV • • • • • • • • •
87V • • • • • • • • •
187/189 • • • • • • • • •
287/289 • • • • • • • • •
45/8845/8846 • • • • • • • • •
39/41B • • • • • • • • •
43B • • • • • • • • •
90 Series • • • • • • • • •
120 Series • • • • • • • • •
190 Series • • • • • • • • •
323/324/325 • • • • • • • • •
370 Series, 381 • • • • • • • • •
705/707 • • • • • • • • •
712/713 • • • • • • • • •
715 • • • • • • • • •
716/717 • • • • • • • • •
718 • • • • • • • • •
725/726 • • • • • • • • •
741/743 • • • • • • • • •
744 • • • • • • • • •
787/789 • • • • • • • • •
1577/1587 • • • • • • • • •
Test lead compatibility chart
Fluke test leads broaden
the ability to take meter
measurements in different
environments. They include
probe-in-one as well as
modular test leads (with clips
and probes), and patch cords
of various lengths. All test
leads are 1.5 m (59 in) long.
TL175
Model number TL71 TL75 TL76 TL221 TL222 TL224 TL910
AC175 • • •
AC87 •••
AC89 •••
AC220 • • •
AC280 •••
AC283 •••
AC285 •••
AC288 •••
FTP-1 • • •
TLK290 •••
TLK291 •••
TP1 •••
TP2 •••
TP4 • • •
TP38 •••
TP74 •••
TP80 •••
TP175 •••
TP220 •••
TP912
TP920 • •
T5 Starter Kit (compatible with T5/T+/T+Pro/330 Series Clamp Meters)
TP165X (compatible with 1503/1507/1577/1587)
Clips and probes compatibility chart Did you know?
Because they are an integral part of the com-
plete measurement system, worn or under-rated
test leads can cause inaccurate readings and
pose a serious shock or electrocution hazard
if live wires are read as being de-energized.
To avoid these risks, use these precautions:
Use the correct test probe for the application.
Confirm that your meter and test accessory
safety ratings meet or exceed the voltage
level you plan to test. See the “Electrical
measurement category ratings for test tools”
chart on page 11 of this catalog for more
information.
Inspect your test leads before use to ensure
the insulation is not nicked or cracked from
age. Typically, you should plan on replacing
your test leads every 18months.
Ensure there are no gaps or cracks at the
junction between the insulated wire and
banana plugs or probes at each end
of the lead.
Conduct a simple ohms measurement to
confirm that your tools are electrically
reliable and carry a signal within allowable
loss parameters.
5
For more information, go to www.fluke.com/accessories
TL175 Left to right: AC283, AC280, TP175, AC285, AC220, and TL224
Test leads
TL71 Premium Test
Lead Set
One pair (red, black) comfort grip
probes with flexible silicone-
insulated, right-angle test leads.
Heat and cold resistant
Safety rating: CAT II 1000 V, 10
A (CAT III 1000 V, CAT IV 600 V
with protective cap)
TL76 2mm/4mm
Test Lead Set
One pair (red, black) silicone test
leads with right angle shrouded 4
mm (0.16 in) banana plugs.
Removable lantern tip for use
with European wall sockets,
4 mm (0.16 in) diameter
Removable lantern tip for easy
access to terminal blocks, 2mm
(0.08 in) diameter
GS38 probe caps (removable)
allow probing in CAT II, III and
CAT IV environments
Safety rating: CAT II 1000 V, 10
A (CAT III 1000 V, CAT IV 600 V
with protective cap)
TL26A
TL76
TL40 Retractable Tip
Test Lead Set
One pair (red, black) flexible
silicone insulated test leads with
sharp needle point tips adjustable
to desired length from
0 mm to 76 mm.
Extra hard probe tips to
provide long service life
Safety rating: CAT II 600 V,
3A rating
TL26A 60 in 5-Way
Test Lead Set
One pair (red, black) silicone-
insulated leads with five different
ways to connect.
U-shaped nose for blade-shaped
terminals
Notched jaw for gripping screw
heads, bare wire or
terminals
Serrated teeth for gripping
threaded or wire-wrapped
terminals
Sharp needle cluster for
piercing small gauge
(#22-#28 AWG) wires
Large piercing needle
Safety rating: 30 V, 10 A
TL910 Electronic
Test Probes
One pair (red, black) leads with
very small tips to access hard-to-
reach electronic test points.
Includes three sets of spring-
loaded gold tips and two sets of
stainless steel tips
Tip length up to 100 mm (4 in)
Tip diameter: 1 mm (0.04 in)
Safety rating: CAT II 1000 V, 3A
TL175 TwistGuard Test
Leads
Probes meet IEC 61010-031
requirements for safety
Patented extendable tip guard
meets CAT III 1000 V, CAT IV
600 V requirements while pro-
viding the flexibility you need
for CAT II measurements
WearGuard test lead wear
indicator show white inner
layer when leads are damaged
or worn and in need of replace-
ment
Probes always show correct cat-
egory rating for tip length being
used
Advanced strain relief exceeds
5,000 bend life
2 mm (0.08 in) diameter probe
tips
Available as a modular test
probe under TP175 (page 10)
TL75 Hard Point Test
Lead Set
One pair (red, black) comfort grip
probes with PVC-insulated, right-
angle shrouded 4 mm (0.16 in)
banana plugs.
Safety rating: CAT II 1000 V,
10 A (CAT III 1000 V, CAT IV
600 V with protective cap)
Test lead/probe-in-one
Test lead and probe-in-one accessories offer the convenience of a test lead and
probe-in-one unit with a variety of connections.
TL71
TL75
TL175
TL40
6
Test leads
Test leads
New! AC288 SureGrip
Terminal Block Probe
One pair (red, black) of probes
features a retractable probe tip for
connections to clamp and screw
type terminal blocks.
Designed for increased safety,
while providing the flexibility
to reach deep connection points
1 mm diameter probe tip
extends out to 8.4 mm (0.33 in)
length
Recommended for use with the
TL224, TL222, TL221 test leads
Safety rating: CAT III 1000 V,
CAT IV 600 V
Probe-in-one clips
Probe-in-one clips and adapters expand the application of
probe-in-one test leads.
TL910
TP912
TP165X
AC175
AC173
AC288
TP920
TP912 Replacement
Tips for TL910
Five sets of spring-loaded, tips to
refurbish TL910 Electronic Test
Probes.
Very small 1 mm (0.04 in)
tips to access hard-to-reach
electronic test points
Probe tip length up to 100 mm
(4 in)
Three sets of gold-plated and
two sets of stainless steel tips
TP165X Remote
Control Probe
Probe with integrated test button
simplifies measurement when
accessing hard-to-reach points.
Probe designed for 1500 Series
insulation and 1650 Series
installation testers
Tip length up to .735 in
Tip diameter: 1 mm (0.04 in)
Safety rating: CAT II 1000 V,
(CAT III 1000 V, CAT IV 600 V
with protective cap), 10 A
AC173 Alligator Clip Set
One pair (red, black) slide-on
alligator clips.
8 mm (0.32 in) clip opening
Slide-on alligator clips are com-
patible with 4mm banana plugs
and test leads, such as the
TL221, TL222, TL224
Safety rating: CAT IV 600 V,
CAT III 1000 V, 10 A
AC175 Alligator Clip Set
One pair (red, black) slide-on
alligator clips.
8 mm (0.32 in) clip opening
Slide-on alligator clips are com-
patible with TL71, TL75, TL175
and TP175 test probes
Safety rating: CAT IV 600 V,
CAT III 1000 V, 10 A
TP920 Test Probe
Adapter Set
Three pairs (red, black) push-on
adapters.
Includes IC test adapters,
extended probe tips, and
medium alligator clips
Maximum opening 7.6 mm
(0.3 in)
Safety rating: IC test adapter
CAT II 300 V, extended probe
tips CAT II 300 V, medium alli-
gator clips CAT II 1000 V
7
For more information, go to www.fluke.com/accessories
TL221 SureGrip Test
Lead Extensions Set
One pair (red, black) silicone-
insulated leads with safety-
shrouded, 4 mm (0.16 in) banana
plugs.
Couplers have female connec-
tors on both ends
Safety rating: CAT IV 600 V,
CAT III 1000 V, 10 A
TL222 SureGrip Silicone
Insulated Test Leads
One pair (red, black) silicone-
insulated test leads (red, black)
with safety-shrouded, 4 mm
(0.16 in) banana plugs.
Right angle connectors on both
ends
Modular test leads
Modular test leads provide the convenience of attaching clips, hooks and grabbers, as
needed. All of these leads are 1.5 m (59 in) long, offer reinforced strain relief, and include
banana jack terminations that allow a great variety of test lead configurations.
TL224 SureGrip
Insulated Test Leads
One pair (red, black) silicone-
insulated test leads with
safety-shrouded 4mm (0.16 in)
banana plugs.
Right angle connector on one
end and straight connector on
the other
Safety rating: CAT IV 600 V,
CAT III 1000 V, 10 A
TL27 Heavy-duty Test
Lead Set
One pair (red, black) rugged,
EPDM-insulated test leads with
safety-shrouded 4 mm (0.16 in)
banana plugs.
Straight connectors on both
ends
Safety rating: CAT III 1000 V,
10 A
TL221
TL222
TL224
TL27
Test lead holder
H900 Test Lead Holder
Heavy-duty holder for conve-
niently storing test lead wires.
Mounting holes for securing to
wall or other surfaces
For test lead wires up to 8 mm
(0.31 in) in diameter
Overall dimensions (LxWxH):
27.9 cm x 8.9 cm x 3.2 cm
(11 in x 3.5 in x 1.25 in)
H900
8
Superior gripping
surface made from
thermoplastic rubber
SureGrip accessories
SureGrip accessories were designed to
provide a reliable grip in slippery hands.
Rubber-overmolded surfaces and
finger-hugging curves give the user
a comfortable, steady hold on the
accessory so they can focus on
making an accurate measurement.
Test leads
Ergonomic
design
AC285 SureGrip
Alligator Clips
One pair (red, black) large
alligator clips with insulated,
nickel-plated steel jaws.
Multi-purpose tooth pattern
grips anything from fine gauge
wire to a 20 mm (0.8 in) bolt
Safety rating: CAT IV 600 V,
CAT III 1000 V, 10 A
AC220 SureGrip
Alligator Clips
One pair (red, black) of small,
insulated, nickel-plated jaws.
Blunt tip grabs round screw
heads up to 9.5 mm (0.37 in)
Safety rating: CAT IV 600 V,
CAT III 1000 V, 10 A
AC280 SureGrip
Hook Clips
One pair (red, black) nickel-
plated hook-style clips.
Profile narrows to 5.6 mm
(0.22 in) at tip
Hook opening 6.4 mm
(0.25 in) at front
Base opening of 0.2 mm
(0.08 in)
Safety rating: CAT IV 600 V,
CAT III 1000 V, 3 A
Modular clips (for use with modular test leads)
Using modular test leads, this wide variety of clips allows the configuration of
leads to individual needs.
AC283 SureGrip
Pincer Clips
One pair (red, black) nickel-
plated pincers open to 5 mm
(0.2 in). Perfect for continuity
testing on circuit board compo-
nents such as diodes.
11.4 cm (4.49 in) flexible
insulated shaft
Safety rating: CAT IV 600 V,
CAT III 1000 V, 1 A
AC89 Heavy Duty Insula-
tion Piercing Test Clip
Ideal probe for establishing accu-
rate contact through
insulation.
Pierces 0.25 mm to 1.5 mm
(0.01 in to 0.06 in) insulated
wire
Safety rating: 1000 V, 10 A
AC87 Heavy Duty Bus
Bar Clip Set
One pair (red, black) flat,
right angle clips designed for
connecting to bus bars.
Adjustable collar provides two
ranges of jaw openings up to
30 mm (1.18 in)
Safety rating: CAT III 600 V, 5A
AC285
AC89
AC280
AC220 AC87
AC283
9
Test leads
For more information, go to www.fluke.com/accessories
TP1 Slim Reach
Test Probes
One pair (red, black) slender
probes with flat stainless steel
blade to hold securely in blade-
type electrical wall sockets.
Tip length up to 14.7 mm
(0.58 in)
Safety rating: CAT II 1000 V,
10 A (CAT III 1000 V, CAT IV
600 V with protective cap)
TP2 Slim Reach
Test Probes
One pair (red, black) slender
stainless steel probes for
accessing closely-spaced or
recessed terminals such as in
electronic environments.
2 mm (0.08 in) diameter tip
Safety rating: CAT II 1000 V,
10 A (CAT III 1000 V, CAT IV
600 V with protective cap)
TP4 Slim Reach
Test Probes
One pair (red, black) slender
stainless steel probes for
accessing closely-spaced or
recessed electrical terminals.
4 mm (0.16 in) diameter probe
tip designed to fit securely into
IEC (C13 and C14) electrical wall
outlets
Safety rating: CAT II 1000 V,
10 A
Modular test probes (for use with modular test leads)
Using modular test leads, this wide variety of test probes allows the configuration of leads
for a wide variety of needs, whether industrial, electrical, or electronic.
TP80 Electronic
Test Probes
One pair (red, black) electronics
test probes.
IC-insulated cap prevents short-
ening of IC legs for probing high
density components or boards
Tip length up to 3.9 mm
(0.157in)
Tip diameter: 1 mm (0.04 in)
Safety rating: CAT III 1000 V,
1 A
TP74 Lantern Tip
Test Probes
One pair (red, black) featuring
nickel-plated brass ends.
Banana-style 4 mm (0.16 in)
spring contacts
Safety rating: CAT II 1000 V,
10 A (CAT III 1000 V, CAT IV
600 V with protective cap)
TP38 Slim Reach
Test Probes
One pair (red, black) slender
stainless steel probes for
accessing closely-spaced or
recessed terminals.
Tip length: 24 mm (0.95 in)
which includes the insulated
part of the tip
Probe tip insulated to 4 mm
(0.16 in) from the end
Safety rating: CAT IV 600 V,
CAT III 1000 V, 10 A
TP175 TwistGuard
Test Probes
Modular test probes of the pop-
ular TL175 Test Leads (page 6)
Patented extendable tip guard
meets CAT III 1000 V, CAT IV
600 V requirements while pro-
viding the flexibility you need
for CAT II measurements
2 mm (0.08 in) diameter stain-
less steel probe tips
TP220 SureGrip
Industrial Test Probes
One pair (red, black) industrial
test probes with stainless
steel tip.
Sharp, 12 mm (0.47 in) tips
Safety rating: CAT II 1000 V
(CAT III 1000 V, CAT IV 600 V
with protective cap), 10 A
TP220TP175
TP4
TP74
TP80
TP38
TP1
TP2
10
Test leads
How to choose the best test probe for your job?
Measurement
category In brief Examples
CAT IV Three-phase at
utility connection,
any outdoor mains
conductors
Refers to the origin of installation, i.e., where low-voltage
connection is made to utility power
Electricity meters, primary overcurrent protection equipment
Outside and service entrance, service drop from pole to
building, run between meter and panel
Overhead line to detached building, underground line to well
pump
CAT III Three-phase
distribution, including
single-phase
commercial lighting
Equipment in fixed installations, such as switchgear and
polyphase motors
Bus and feeder in industrial plants
Feeders and short branch circuits, distribution panel devices
Lighting systems in larger buildings
Appliance outlets with short connections to service entrance
CAT II Single-phase
receptacle connected
loads
Appliance, portable tools, and other household and similar
loads
Outlet and long branch circuits
Outlets at more than 10 meters (30 feet) from CAT III source
Outlets at more that 20 meters (60 feet) from CAT IV source
IEC 61010 electrical measurement category ratings for test tools
Make sure that your accessory ratings meet or exceed the rating of your measurement environment.
Patch cords
Patch cords connect two test points or two test instruments or accessories together.
TL932 Patch Cords (90 cm)
One pair (red, black) multi-
stacking banana plug patch cords,
90 cm (35.4 in) long.
Nickel-plated, 4 mm (0.16 in)
banana plugs
90 cm long PVC insulated leads
30V rms or 60V dc, 15 A
TL930 Patch Cords (60 cm)
One pair (red, black) multi-
stacking banana plug patch cords,
61 cm (24 in) long.
Nickel-plated, 4 mm (0.16 in)
banana plugs
61 cm long PVC insulated leads
30V rms or 60 V dc, 15 A
TL935 Patch Cords
(60 cm, 90 cm, 120 cm)
Three sets (red and black pairs) of
multi-stacking banana plug patch
cords in different lengths.
Nickel-plated, 4 mm (0.16 in)
banana plugs
60 cm, 90 cm, and 120 cm
(23.6 in, 35.4 in, and 47.2 in)
long PVC insulated leads
30 V rms or 60V dc, 15 A
TL940 Mini-Hook Test
Leads
One pair (red, black) of test leads
with multi-stacking 4 mm banana
plugs and mini-hooks.
Mini-hooks attach to component
leads up to 1.5 mm diameter
90 cm long PVC insulated leads
30 V rms or 60 V dc, 3 A
TL950 Mini-Pincer Test Leads
One pair (red, black) of test leads
with multi-stacking 4 mm banana
plugs and mini-pincers.
Mini-pincers open to 2.3 mm
90 cm long PVC insulated leads
30 V rms or 60 V dc, 3 A
TL960 Micro-Hook Test Leads
One pair (red, black) of test leads
with multi-stacking 4 mm banana
plugs and micro-hooks.
Micro-hooks attach to component
leads up to 1 mm diameter
90 cm long PVC insulated leads
30 V rms or 60 V dc, 3 A
TL970 Hook and Pincer Set
TL940 Mini-Hook Test Lead Set
TL950 Mini-Pincer Test Lead Set
TL960 Micro-Hook Test Lead Set
11
Test leads
For more information, go to www.fluke.com/accessories
Test lead sets and kits
Model number TL27 TL80A TL81A TL220 TL223 TL225 TL238 TLK-220 TLK-225 TLK287 TLK289 TLS430
10/11/12/12B •••••••••••
(compatible with 430 Series Power Quality Analyzer)
110/111/112 •••••••••••
114/115/116/117 •••••••••••
20/70 Series •••••••••••
27 •••••••••••
70/73 III •••••••••••
175/177 •••••••••••
179 •••••••••••
80 Series III/83V •••••••••••
87/89 IV •••••••••••
87V •••••••••••
187/189 •••••••••••
287/289 •••••••••••
45/8845/8846 •••••••••••
39/41B •••••••••••
43B •••••••••••
90 Series •••••••••••
120 Series •••••••••••
190 Series •••••••••••
323/324/325 •••••••••••
370 Series, 381 •••••••••••
705/707 •••••••••••
712/713 •••••••••••
715 •••••••••••
716/717 •••••••••••
718 •••••••••••
725/726 •••••••••••
741/743 •••••••••••
744 •••••••••••
787/789 •••••••••••
1577/1587 •••••••••••
Test lead sets and kits compatibility chart
Expand your testing capability or
update your tools with these test lead
sets and kits. Designed for industrial,
electrical, and electronic needs,
these collections range from starter
to master test lead selections.
12
TLK-225
Model number TL27 TL80A TL81A TL220 TL223 TL225 TL238 TLK-220 TLK-225 TLK287 TLK289
AC175 • •
AC87 • •••••••••
AC89 • •••••••••
AC220 • •••••••••
AC280 • •••••••••
AC283 • •••••••••
AC285 • •••••••••
FTP-1 • •••••••••
TLK290 •••••••••
TLK291 •••••••••
TP1 • •• ••••••
TP2 • •••••••••
TP4 • •••••••••
TP38 • •••••••••
TP74 • •••••••••
TP80 • •••••••••
TP175 • •••••••••
TP220 • •••••••••
TP912
TP920 • •
T5 Starter Kit (compatible with T5/T+/T+Pro/330 Series Clamp Meters)
TP165X (compatible with 1503/1507/1577/1587/1650 Series)
Clips and probes compatibility chart
TLK289 Industrial Master
Test Lead Set
Designed for electrical and
electronics testing in today’s
industrial environment including
clips and probes for dependable
contact with a variety of test
points. Includes eight items:
One pair each (red, black)
AC285 SureGrip Alligator
Clips
AC220 SureGrip Alligator
Clips
AC280 SureGrip Hook Clips
TP220 SureGrip Industrial
Test Probes
TPAK ToolPak
80BK-A Integrated DMM
Temperature Probe
C116 Soft Carrying Case
TLK287 Electronics Master
Test Lead Set
The perfect test lead set for
todays electronics test and
design. Includes 11 items:
Precision electronic probes with
multiple spring-loaded sharp
tips to maximize contact with
SMD test points
Micro-grabbers and leads to
enable fine SMD testing
Mini-alligator clips, grabbers,
and probes for virtually every
electronics need
Modular test leads and
lead-probe combinations
Couplers for long lead
applications
TLK289
TLK287
13
For more information, go to www.fluke.com/accessories
Test lead sets and kits
TL80A Basic Electronic
Test Lead Kit
The fundamental accessories for
testing are included in this four-
item kit.
Medium alligator clip
CAT II1000 V, 10 A
Extended probe tips
CAT II 300 V, 3 A
TL71 Premium Test Lead Set
C75 Accessory Case
TLK-225 SureGrip
Master Accessory Set
Set includes all the SureGrip
leads, clips, and probes in
a handy roll-up pouch. This
13-item set includes:
AC220 SureGrip Alligator Clips
AC280 SureGrip Hook Clips
AC283 SureGrip Pincer Clips
AC285 SureGrip Alligator Clips
TP175 TwistGuard Test Probes
TL224 SureGrip Insulated Test
Leads
Six-pocket storage pouch
Safety rating: all CAT IV
600 V, CAT III 1000 V
TL223 SureGrip
Electrical Test Lead Set
All-in-one set includes three test
lead accessories:
AC220 SureGrip Alligator Clips
TP1 Slim Reach Test Probes
(flat-bladed)
TL224 SureGrip Insulated Test
Leads
Safety rating: CAT II 1000 V, 10
A (CAT III 1000 V, CAT IV 600 V
with protective cap)
TLK-220 US SureGrip
Industrial Test Lead Kit
Special-value SureGrip
five-piece kit for industrial appli-
cations, in a roomy
carrying case. Kit includes:
AC220 SureGrip Alligator Clips
AC285 SureGrip Alligator Clips
TP220 SureGrip Industrial Test
Probes
TL224 SureGrip Insulated Test
Leads
C116 zippered vinyl case with
moveable divider
Safety rating: CAT II 1000 V
(CAT III 1000 V, CAT IV 600 V
with protective cap), 10 A
TLK-225
TL223
TLK-220
TL81A Deluxe Electronic
Test Lead Kit
This 11-item kit includes pouch
and two each (red, black) of:
Test leads with a safety-
shrouded, right angle banana
connector on one end and a
stainless steel test probe on the
other. Rated up to 10 A.
Insulated alligator clips. Rated
up to 10 A
Insulated probe tip extenders.
Rated up to 3 A
Modular test probes with
banana jack connector. Rated
up to 10 A
Modular hook-style clip test
leads. Rated up to 5 A
Modular pinch-style clip test
leads. Rated up to 5 A
Modular alligator clips. Rated up
to 10 A
Slide-on IC probe tip adapters
(rated up to 3 A) and test lead
couplers
Bare spade lug. Rated to 10 A
TL220 SureGrip
Industrial Test Lead Set
Handy all-in-one set that includes
essential test items
for industrial environments.
Three-item set includes:
AC220 SureGrip Alligator Clips
TP220 SureGrip Industrial
Test Probes CAT II 1000 V,
10 A without protective cap
TL224 SureGrip Silicone Insu-
lated Test Leads
Safety rating: all CAT IV
600 V, CAT III 1000 V
TL220
TL81A
TL80A
14
FTP-1 / FTPL-1 SureGrip
Fused Test Probes
Built-in fuses for added
protection
2 mm threaded probe tips
include removable 4 mm
lantern-style spring contacts
FTPL-1 comes with a set of
TL224 SureGrip Silicone
Insulated Test Leads
Safety rating: CAT II 1000 V
(CAT III 1000 V, CAT IV 600 V
with protective cap), 10 A
T5 Starter Kit
Special-value three-piece kit for
the electrical professional with a
Fluke T5 Voltage, Continuity and
Current Tester. Kit includes:
TP238 Insulated Test Probes
AC285 SureGrip Alligator Clips
C33 Soft Carrying Case
Safety rating: all CAT IV
600 V, CAT III 1000 V
TLS430 Test Leads
and Alligator Clips
Test lead replacement set for the
Fluke 430 Series Three-Phase
Power Quality Analyzers.
Set includes five each
(4 black, 1 green) of test
leads and alligator clips
Safety rating: CAT IV 600 V,
CAT III 1000 V
TL238 SureGrip Test
Lead Set for High Energy
Environments
This kit is specially designed
for high energy environments.
Three-piece kit includes:
TP238 SureGrip Insulated
Test Probe Set
TP280 SureGrip Test Probe
Extender
TL224 SureGrip Insulated
Test Leads
Safety rating:
TP238 and TL224: CAT IV
600 V, CAT III 1000 V, 10 A
TP280: CAT III 1000 V, 10 A
TL225 SureGrip
Stray Voltage Adapter
Test Lead Kit
The Fluke TL225 adds low input
impedance to a multimeter,
desensitizing it to low energy
and eliminating ghost or stray
voltages. Four-piece kit includes:
SV225 Stray Voltage Adapter
TL224 SureGrip Insulated Test
Leads
TP238 Insulated Test Probes
C75 Accessory Case
Safety rating: All CAT IV 600V,
CAT III 1000 V, 10 A
For more information on the adapter,
see page 47.
TLK290 Flexible Socket
Probe Set
Set includes three flexible socket
probes and a large alligator clip for
use with 4 mm (0.16 in) shrouded
test leads.
Test probes are for use on motor
and three-phase sockets
Probes have flexible test points
that fit securely between 4 mm
and 8 mm (0.16 in and 0.32 in)
sockets
Alligator clip opening: 20mm
(0.8 in)
Safe contact such as in CEE 16A
and CEE 32 A plugs
Safety rating: CAT II 1000 V, 8 A
TLK291 Fused Test
Probe Set
One pair (red, black) fused test
probes offer added measure-
ment protection by providing firm
and secure contact. Probes fit on
modular leads or on fixed-lead test
tools.
Each probe contains a
500 mA/1000 V/50 kA fuse
Safety rating: CAT IV 600 V,
CAT III 1000 V
TLK291
TL238
TL225
TLS430
TLK290
FTP-1 FTPL-1
T5 Starter Kit
15
For more information, go to www.fluke.com/accessories
Test lead sets and kits
Bead HVAC Immersion Surface Air Piercing
General
purpose
Industrial
surface
Pipe
clamp
80BK-A
80PK-1
80PJ-1 80PK-11 80PK-22 80PK-3A 80PK-24
80PK-25
80PT-25 80PK-26 80PK-27 80PK-8
Lowest
temperature
-40 °C (-40 °F) -30 °C
(-22 °F)
-40 °C
(-40 °F)
0 °C
(32 °F)
-40 °C
(-40 °F)
Type K:
-40 °C
(-40 °F)
Type T:
-196 °C
(-321 °F)
-40 °C
(-40 °F)
-127 °C
(-196 °F)
-29 °C
(-20 °F)
Highest
temperature
260 °C
(500 °F)
105 °C
(221 °F)
1090 °C
(1994 °F)
260 °C
(500 °F)
816 °C
(1500 °F)
350 °C
(662 °F)
816 °C
(1500 °F)
600 °C
(1112 °F)
149 °C
(300 °F)
Probe material Type K wire with
teflon insulation
Velcro Inconel 600 Type K sensor
with teflon
body
Inconel 316 Stainless
Steel
304 Stainless
Steel
304 Stainless
Steel
Type K sensor
with pvc body
Probe length 1 m lead
wire
1 m lead wire 19 m Velcro
cuff
21.27 cm
(8.375 in)
9.525 cm
(3.75 in)
21.59 cm
(8.5 in)
10.16 cm
(4 in)
21.57 cm
(8.5 in)
20.32 cm
(8 in)
for pipes from
6.4 mm
(.25 in)
to 34.9 mm
(1.375 in)
Cable length 1 m (39 in) 1 m (39 in) 1 m (39 in) 1 m (39 in) 1.3 m (4 ft) 1 m (39 in) 1 m (39 in) 1 m (39 in) 1 m (39 in) 1 m (39 in)
Connection Standard
banana
jack
Molded
thermocouple
plug
Molded
thermocouple
plug
Molded
thermocouple
plug
Molded
thermocouple
plug
Molded
thermocouple
plug
Molded
thermocouple
plug
Molded
thermocouple
plug
Molded
thermocouple
plug
Molded
thermocouple
plug
SureGrip
handle
No No No Yes No Yes Yes Yes Yes No
Key feature Ideal for initial troubleshoot-
ing. Can be secured
in place with a magnet.
Velcro probe
allows
hands free
temperature
measurement.
For use in
liquids or
in gels.
Exposed junc-
tion for direct
contact with
flat or slightly
convex
surfaces.
Perforated
baffle for
air and
non-caustic
gas measure-
ments.
Probe material
safe for use in
foods. Sharp
tip pierces
solid surfaces.
Use for general
purpose air
or surface
measurements.
Low conduc-
tivity stainless
steel mini-
mizes thermal
shunting.
Extra rugged.
Clamps
securely
to pipe.
Measurements
are repeatable
to 0.56 °C
(1 °F).
Thermocouple
types
K K, J K K K K K, T K K K
Typical use
General
purpose • • • • •
HVAC • • •
Food service • •
Industrial • •
Residential • • •
Commercial • • • • •
Temperature specifications
Temperature accessories
These temperature probes
expand the functionality
of Fluke thermometers,
while offering the same
rugged reliability of Fluke
test tools.
16
80PK-10
Model number 80AK-A 80BK-A
All 80PK
Probes
80PJ-1/
80PJ-9 80PT-25 80TK
80T-
150UA 80PJ-EXT 80PK-EXT 80PT-EXT 80CK-M 80CJ-M 80PR-60
10/11/12/12B • • ✱ ✱
110/111/112 • • ✱ ✱
114/115/116/117 116 116 ▲ ▲
20/70 Series • • ✱ ✱
27 • • ✱ ✱
70/73 III • • ✱ ✱
175/177 • • ✱ ✱
179 ▲ ▲
80 Series III/83V ✱ ✱
87/89 IV ▲ ▲
87V ▲ ▲
187/189 ▲ ▲
287/289 ▲ ▲
45/8845/8846 • • ✱ ✱
43B • • ✱ ✱
90 Series • • ✱ ✱
120 Series • • ✱ ✱
190 Series • • ✱ ✱
50S/50D • •
51/52/53/54 II • • •
63/66/68 66/68
714 • • •
715 • • ✱ ✱
725/726 • • •
741/743/744 • • •
787/789 • • ✱ ✱
902 • • •
1587 ▲ ▲
1577
561
574/576
Temperature compatibility
Compatible; Requires 80TK; Requires 80AK-A; 116 only: requires 80AK-A
The innovative SureGrip
design from Fluke is
available in select tem-
perature probes. The soft
rubber handle and
comfortable ergonomic
shape make it easier to
hold the probe and focus
on the measurement.
17
For more information, go to www.fluke.com/temp-accy
Left to right: 80PK-27,
80PK-26, 80PK-24
Temperature accessories
General purpose
measurements
80PJ-1 or 80PK-1
Bead Probe
Type J or K thermocouple probe
for general-purpose applications.
Ideal for troubleshooting.
1 m (39 in) lead
1 mm (0.04 in) probe with
Teflon® insulation
Measurement range: -40 °C to
260 °C (-40 °F to 500 °F)
80PJ-9 or 80PK-9
General Purpose Probe
Type J or K thermocouple probe
for air and non-caustic gases.
The sharp tip pierces pipe insula-
tion and the flat surface makes
good contact.
1 m (39 in) lead
15.25 cm (6 in) stainless steel
probe
Measurement range: -40 °C to
260 °C (-40 °F to 500 °F)
80PK-26 SureGrip
Tapered Temperature
Probe
Type K thermocouple probe with
tapered tip for speedy air, sur-
face, non-caustic gas, and liquid
measurements.
1 m (39 in) lead
203 mm (8 in) stainless steel
probe
Measurement range: -40 °C to
816 °C (-40 °F to 1500 °F)
Surface measurements
80PK-3A Surface Probe
Type K thermocouple with
exposed junction for flat or
slightly convex surfaces such as
plates and rollers.
1.3 m (4 ft) lead
9.525 cm (3.75 in) probe with
Teflon® insulation
Measurement range: 0 °C to
260 °C (32 °F to 500 °F)
80PK-27 SureGrip
Industrial Surface
Temperature Probe
Type K thermocouple probe for
surfaces in rugged environments.
1 m (39 in) lead
20.32 cm (8 in) stainless steel
probe
Measurement range: -127 °C to
600 °C (-197 °F to 1112 °F)
Piercing measurements
80PK-25 or 80PT-25
SureGrip Piercing
Temperature Probe
Type K or T thermocouple suit-
able for food industry, liquids,
and gels. Sharp tip pierces solid
surfaces.
1 m (39 in) lead
10.16 cm (4 in) stainless steel
probe
Measurement range:
Type K: -40 °C to 350 °C
(-40 °F to 662 °F)
Type T: -196 °C to 350 °C
(-321 °F to 662 °F)
Temperature probes
These temperature probes expand the functionality of Fluke thermometers, while offering
the same rugged reliability of Fluke test tools.
Air measurements
80PK-24 SureGrip
Air Temperature Probe
Type K thermocouple probe
for air and non-caustic gas mea-
surements.
1 m (39 in) lead
21.59 cm (8.5 in) Inconel® probe
Bead protected by perforated
baffle
Measurement range: -40 °C
to 816 °C (-40 °F to 1500 °F)
Immersion
measurements
80PK-22 SureGrip Immer-
sion Temperature Probe
Type K thermocouple probe for
use in liquids and gels.
1 m (39 in) lead
21.27 cm (8.375 in) Inconel®
probe
Measurement range: -40 °C to
1090 °C (-40 °F to 1994 °F)
Pipe measurements
80PK-8 and 80PK-10 Pipe
Clamp Temperature Probe
Type K thermocouple clamps
securely to pipes for fast
temperature and superheat
measurements.
Durable ribbon sensor
1 m (39 in) lead
80PK-8 for pipe diameters
6.4 mm to 34.9 mm (0.25 in to
1.375 in)
80PK-10 for pipe diameters
32 mm to 64 mm (1.25 in to
2.5 in)
Measurements are repeatable to
0.56 °C (1 °F)
Measurement range: -29 °C to
149 °C (-20 °F to 300 °F)
80PK-1
80PK-9
80PK-26
80PK-3A
80PK-27
80PK-25
80PK-24 80PK-22
18
Temperature accessories
80PK-11 Type-K
Velcro® Thermocouple
Temperature Probe
Type K Velcro cuff for use with
any temperature-measuring
instrument that accepts type K
thermocouples.
Use multiples and leave in
place for route-based routine
maintenance
1 m (39 in) lead
48 cm (19 in) Velcro® cuff
Measurement range: -30 °C to
105 °C (-22 °F to 221 °F)
80PK-18 Pipe Clamp
Temperature Probe Kit
Includes both 80PK-8 and
80PK-10 Type K clamps
Provides full range of pipe
measurement sizes
Includes soft carrying case to
conveniently keep both clamps
handy for any situation
Contact measurements
(for use with non-contact
infrared thermometers)
80PR-60 RTD Temperature
Probe
This probe expands the utility
of an RTD non-contact infrared
thermometer by simultaneously
taking contact and non-contact
temperature readings.
For use with the Fluke 66 and
68 Infrared Thermometers
1 m (39 in) lead
90 mm (3.5 in) platinum
1KW probe
3.5 mm (0.14 in) phono
type jack
Measurement range: -40 °C
to 260 °C (-40 °F to 500 °F)
Temperature adapters
for DMMs
80AK-A Thermocouple
Adapter
Adapts type K thermocouple
mini-connector to dual shrouded
4 mm (0.16 in) banana plug
inputs.
Measurement range and
accuracy: probe dependent
Suitable for low voltage applica-
tions (below 30 V ac, 60 V dc)
80BK-A Integrated DMM
Temperature Probe
Convenient, integrated type K
thermocouple probe with stan-
dard shrouded 4 mm (0.16 in)
banana jack.
Compatible with Fluke DMM
with temperature measurement
functions
1 m (39 in) lead
Measurement range: -40 °C to
260 °C (-40 °F to 500 °F)
80TK Thermocouple
Module
This module converts a DMM to a
thermometer and is designed for
use with type K thermocouples in
low voltage applications.
Voltage range: below 24 V ac,
60V dc
1 m (39 in) lead
Measurement range: -50 °C
to 1000 °C (-58 °F to 1832 °F)
(probe dependent)
80T-150UA Universal
Temperature Probe
Adapts any DMM using shrouded 4
mm (0.16 in) banana plugs. This
fast, accurate integrated probe is
designed for
low-voltage applications.
For air, surface, and non-
corrosive applications
Voltage range: below 24 V ac,
60 V dc
1.1 m (42 in) lead
15.7 cm (6.2 in) probe tip
Measurement range: -50 °C to
150 °C (-58 °F to 302 °F)
Output: switchable, from
1 mVC to 1 mV/°F
Other temperature
accessories
80CJ-M or 80CK-M
Male Mini-Connectors
Type J or K thermocouple,
suitable for up to 20-gauge
thermocouple wire.
Isothermal screw terminal
for J wire
Two per package
80PJ-EXT, 80PK-EXT,
or 80PT-EXT Extension
Wire Kit
This kit extends and repairs type
J, K, or T thermocouple wires for
thermometers.
Includes 3 m (118 in) of
thermocouple wire and
one pair of male/female
mini-connectors
Maximum continuous
exposure temperature:
260 °C (500 °F)
80PK-8
80PK-10
80PK-11
80PR-60
80AK-A
80TK
80CJ-M 80PJ-EXT
80BK-A
80T-150UA
19
For more information, go to www.fluke.com/accessories
Current clamps: AC
i5s i200 i200s i400 i400s i800 i1000s i3000s
AC range 10 mA to 5 A 0.5 A to 240 A 0.5 A to 240 A 1 A to 400 A 0.5 A to 400 A 0.1 A to 800 A 100 mA to 1000 A 1 A to 3000 A
Accuracy 10 mA to 1 A 1%
+ 5 mA
1 A to 5 A 1%,
48 Hz to 65 Hz
< 3 % +0.5 A
48Hz to 65Hz
< 1 % +0.5 A
48 Hz to 65Hz
2 % + 0.06 A
45 Hz to 400Hz
.5 A to 40A,
2 % + .015A,
5 A to 400A,
2 % + .04A,
45 Hz to 400 Hz
± 2 % of rdg.,
50 Hz to 1 kHz
± 3 % of rdg.,
(typical)
30 Hz to 50 Hz
and 1 kHz to 10
kHz
0.2 to 10 A:
3 % + 0.1 A
10 A to 100 A:
2 % + 0.5 A
100 A to 1000A:
1 % + 1 A
48 Hz to 65 Hz
1 A to 30 A:
2 % + 0.1 A
1 A to 300 A:
2 % + 0.5 A
1 A to 3000 A:
2% + 2 A
48 Hz to 65 Hz
Bandwidth (-3 dB) 40 Hz to 5 kHz 10 kHz to 40 kHz 40 Hz to 40 kHz 5 Hz to 20 kHz 5 Hz to 10 kHz 30 Hz to 10 kHz 10 Hz to 100 kHz 10 Hz to 100 kHz
Maximum
conductor dia.
15 mm
(0.59 in)
20 mm
(0.8 in)
20 mm
(0.8 in)
32 mm
(1.25 in)
32 mm
(1.25 in)
54 mm
(2.13 in)
54 mm
(2.13 in)
64 x 100 mm
(2.52 in x 3.94 in)
Maximum
conductor size
2 AWG 300 MCM 300 MCM 750 MCM 750 MCM 2-500 MCM or
1-1000 MCM
2-500 MCM or
1-1000 MCM
64 mm
(2.52 in)
Output levels 400 mV/A 1 mA/A 10 mV/A
100 mV/A
1 mA/A 10 mV/A
1 mV/A
1 mA/A 1 mV/A
10 mV/A
100 mV/A
10 mV/A
1 mV/A
0.1 mV/A
Output cable 2.5 m to BNC
termination
1.5 m shrouded
banana plugs
2 m to BNC
termination
1.5 m shrouded
banana plugs
2.5 m to BNC
termination
1.6 m shrouded
banana plugs
1.6 m to BNC
termination
2.1 m to BNC
termination
Warranty One-year One-year One-year One-year One-year One-year One-year One-year
Safety rating CAT III 600 V CAT III 600 V CAT III 600 V CAT III 1000 V
CAT IV 600 V
CAT III 1000 V
CAT IV 600 V
CAT III 600 V CAT III 600 V CAT III 600 V
i430-flex i2000 flex i3000s flex-24/i3000s flex-36 i6000s flex-24/i6000s flex-36
AC range 30 A to 3000 A 20 A to 2000 A 30 A to 3000 A 60 A to 6000 A
Accuracy ± 1 % of reading at 25 °C, 50 Hz ± 1 % of range 45 Hz to 65 Hz
Ranges: 20 A, 200A, 2000 A
± 1 % of range, 45 Hz to 65 Hz,
Ranges: 30 A, 300A, 3000 A
±1% of range, 45 Hz to 65 Hz,
Ranges: 60 A, 600A, 6000 A
Bandwidth (-3 dB) 10 Hz to 7 kHz 10 Hz to 20 kHz 10 Hz to 50 kHz 10 Hz to 50 kHz
Maximum
conductor dia.
177 mm (7 in) 177 mm (7 in) 177 mm (7 in) or 265 mm (10.4 in) 177 mm (7 in) or 265 mm (10.4 in)
Maximum
conductor size
610 mm (24 in)
circumference
610 mm (24 in)
circumference
610 mm (24 in)
circumference
610 mm (24 in)/915 mm (36 in)
circumference
Output levels 85 mV at 1000 A rms, 50 Hz 100 mV/A, 10 mV/A, 1 mV/A 100 mV/A, 10mV/A, 1 mV/A 50 mV/A, 5 mV/A, 0.5 mV/A
Output cable 2.5 m to BNC termination 2 m with double shrouded
banana plugs
2.1 m to BNC termination 2 m to BNC termination
Battery life No battery 400 hours 400 hours
Warranty One-year One-year One-year One-year
Safety rating CAT III 1000 V,
CAT IV 600 V
CAT III 600 V CAT III 600 V CAT III 600 V
AC current clamp specifications
Fluke current clamps extend the
current ranges of digital multimeters,
power quality analyzers, and oscillo-
scopes and are available for both
ac and ac/dc environments. Most
clamps are made with a soft, non-
slippery overmold handle to prevent
accidental touching of live wires.
20
i400
Model number i5s i200 i200s i400 i400s i800 i1000s i3000s
i2000
FLEX1
i3000s
FLEX
i6000s
FLEX3
10/11/12/
12B/16/18
1 A to
200 A
1 A to
400 A*
0.2 A to
1000A*
1 A to
3000 A
2 A to
2000 A
3 A to
3000A
6A to
6000A
110/111/112 3 A to
200 A
30 A to
400 A*
3 A to
1000A*
30 A to
3000A
3 A to
2000 A
3 A to
3000A
6A to
6000A
114/116 1 A to
200 A
0.6 A to
400 A*
0.2 A to
1000A*
1 A to
3000A
2 A to
2000 A
3 A to
3000A
6A to
6000A
115/117 60 A to
200 A
1 A to
200 A
60 A to
400 A
0.6 A to
400 A*
60A to
800A
0.2 A to
1000A*
1 A to
3000A
2 A to
2000 A
3 A to
3000A
6A to
6000A
21/23/73/75/77
Series III
1 A to
200 A
1 A to
200 A
1 A to
400 A
1 A to
400 A*
0.1A to
800A
0.2 A to
1000 A*
1 A to
3000 A
2 A to
2000 A
3 A to
3000 A
6A to
6000A
26/79 Series III 1 A to 40 A 1 A to
200 A
1 A to
40 A/
200 A to
400 A
2 A to
400 A*
0.4A to
40A, 200A
to 800A
0.2 A to
1000A*
2 A to
3000 A
2 A to
2000 A
3 A to
3000 A
6A to
6000A
27 1 A to
200 A
1 A to
200 A
1 A to
400 A
1 A to
400 A*
0.1A to
800A
0.2 A to
1000A*
1 A to
3000 A
2 A to
2000 A
3 A to
3000 A
6A to
6000A
70 Series III 1 A to
200 A
1 A to
400 A*
0.2 A to
1000 A*
1 A to
3000 A
2 A to
2000 A
3 A to
3000 A
6A to
6000A
77-IV 0.1A to
800A
6A to
6000A
175/177/179 3 A to
200 A
1 A to
200 A
3 A to
400 A
1 A to
400 A*
3A to
800A
0.3 A to
1000A*
3 A to
3000 A
2 A to
2000 A
3 A to
3000 A
6A to
6000A
1577/1587 3 A to
200 A
1 A to
200 A
3 A to
400 A
3 A to
400 A*
3A to
800A
0.3 A to
1000 A*
3 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
83III/83V/88V 2 A to
200 A
1 A to
200 A
2 A to
400 A
1 A to
400 A*
0.25A to
800A
0.2 A to
1000A*
1 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
85/87 Series III
87 Series V
2 A to
200 A
1 A to
200 A
2 A to
400 A
2 A to
400 A*
2A to
800A
0.2 A to
1000A*
2 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
87/89 Series IV
187/189
2.5 A to
200 A
1 A to
200 A
2.5 A to
400 A
0.5 A to
400 A*
2.5A to
800A
0.2 A to
1000A*
1 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
287/289 1 A to
200 A
1 A to
200 A
1 A to
400 A
0.5 A to
400 A*
1A to
800A
0.2 A to
1000A*
1 A to
3000A
2 A to
2000A
3 A to
3000A
8060A/8062A 2 A to
200 A
1 A to
200 A
2 A to 400A 2 A to
400 A*
2A to
800A
0.2 A to
1000A*
2 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
860 Series 1 A to
200 A
1 A to
200 A
1 A to
400 A
3 A to
400 A*
1.5A to
800A
0.3 A to
1000A*
3 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
39/41B 1 A to
200 A21 A to
400 A20.2 A to
1000A21 A to
3000A22 A to
2000 A23 A to
3000 A2
6A to
6000A
43B 0.5 A to
200 A
0.5 A to
400 A
0.1 A to
1000 A
1 A to
3000 A
20 A to
2000 A
30 A to
3000 A
60 A to
6000 A
434/435 10 mA
to 6 A
0.5 A to
200 A
0.5 A to
400 A
0.1 A to
1000 A
1 A to
3000 A
20 A to
2000 A
30 A to
3000 A
60 A to
6000 A
9X Series 0.5 A to
200 A
0.5 A to
400 A
0.1 A to
1000 A
1 A to
3000 A
20 A to
2000 A
30 A to
3000 A
60 A to
6000 A
120 Series 0.5 A to
200 A
0.5 A to
400 A
0.1 A to
1000 A
1 A to
3000 A
20 A to
2000 A
30 A to
3000 A
60 A to
6000 A
190 Series 0.5 A to
200 A
0.5 A to
400 A
0.1 A to
1000 A
1 A to
3000 A
20 A to
2000 A
30 A to
3000 A
60 A to
6000 A
45 DMM 1.5 A to
100 A
1 A to
200 A
1.5 A to
100 A
1.5 A to
400 A*
1.5A to
100A,
500A to
800A
0.15 A to
1000A*
1.5 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
8808A 1 A to
200 A
1 A to
200 A
1 A to
400 A
0.5 A to
400 A*
1A to
800A
0.2 A to
1000A*
1 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
8845A/8846A 1 A to
200 A
1 A to
200 A
1 A to
400 A
1 A to
400 A*
0.5A to
800A
0.2 A to
1000A*
1 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
75X Series 1.1 A to
200 A
11 A to
400 A*
1.1 A to
1000A*
11 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
787/789 50 A to
200 A
1 A to
200 A
50 A to
400 A
2 A to
400 A*
50A to
440A
0.2 A to
1000A*
2 A to
3000A
2 A to
2000A
3 A to
3000A
6A to
6000A
*Requires PM9081/001 Adapters. 1 Three range version. 2Current and watt readings will be multiples of 10 higher or lower than actual on some ranges.
3Current readings will read half of the expected cardinal value on all meters.
AC clamp-on current probe compatibility
21
For more information, go to www.fluke.com/accessories
Left to right: i800, i400, i200s
AC-only clamps
Fluke current clamps provide accurate current measurements
without breaking electric circuits.
i800 AC Current Clamp
This ac current clamp is designed
to extend the current measuring
capability of a digital multimeter
to 800 A ac. It is compatible with
a digital multimeter that accepts
shrouded 4mm (0.16 in) banana
plugs and has an ac milliamp
range.
Current range: 100 mA to
800 A rms ac
Frequency range: 30 Hz to
10 kHz (-3 dB)
Safety rating: CAT III
600 V rms
i400 AC Current Clamp
This high-safety current clamp
for digital multimeters is a
single range 400 A ac clamp
that is designed to offer max-
imum utility in a very compact
shape. It is compatible with
most digital multimeters or
any other current measure-
ment device that accepts 4 mm
(0.16in) shrouded banana plugs
and has an ac milliamp range.
The division ratio is 1000:1.
Current range: 1 A to 400 A ac
Frequency range: 5 kHz to
20 kHz (-3 dB)
Safety rating: CAT IV 600 V,
CAT III 1000 V
i400s AC Current Clamp
This high-safety compact current
clamp with BNC output is a com-
panion to a ScopeMeter or power
quality meter to measure up to
400 A ac.
Current range: 0.5 A to
400 A ac
Frequency range: 5 Hz to
10 kHz (-3 dB)
Optional PM9081/001 Dual
Banana Plug Male to Female
BNC Adapter is available for
digital multimeters
Safety rating: CAT IV 600 V,
CAT III 1000 V
i200 AC Current Clamp
This small-sized single-range
current clamp features safety-
shrouded 4 mm (0.16 in) banana
plugs. It is compatible with most
digital multimeters or other cur-
rent measurement device that
accepts shrouded 4mm (0.16in)
banana plugs and has an ac mil-
liamp range.
Current range: 1 A to 200 A ac
Frequency range: 40 Hz to
40 kHz
Safety rating: CAT III 600 V
i200s AC Current Clamp
This small-sized dual-range cur-
rent clamp offers voltage output
using a safety-insulated BNC
connector. A dual banana-to-BNC
adapter allows the clamp to be
connected to meters with banana
inputs. It is an ideal companion
to a ScopeMeter, power quality
meter, or digital multimeter.
Current ranges: 0.1 A and
200 A ac switchable
Frequency range: 40 Hz to
10 kHz
Safety rating: CAT III 600 V
i2000 Flex AC
Current Clamp
This current probe utilizes the
Rogowski (air-cored coil) prin-
ciple. It can be used to measure
currents up to 2000 A when used
in conjunction with multimeters,
recorders, or data loggers. The
flexible and lightweight mea-
suring head allows quick and
easy installation on thick and
hard-to-reach areas.
Current range: 20 A, 200 A,
and 2000 A ac switchable
Frequency range: 10 Hz to
20 kHz
Safety rating: CAT III 600 V
i1000s AC Current Clamp
This large ac current clamp
expands applications in industrial
and power environments by con-
necting directly to an oscilloscope
using a reinforced coaxial cable
and an insulated BNC connector.
It is ideal for measuring distorted
current waveform rms and har-
monics.
Current range: 0.1 A to
1000 A ac
Frequency range: 10 Hz to
100 kHz
Accurate displays due to a pas-
sive filter that eliminates noise
and ring on rapidly-
rising di/dt waveforms
Optional PM9081/001 Dual
Banana Plug Male to Female
BNC Adapter is available for
digital multimeters
Safety rating: CAT III 600 V
i400
i400s
i200
i200si800
22
Current clamps: AC
i3000s AC Current Clamp
This ac current clamp is designed
as a clamp-on unit for use with
oscilloscopes. It also includes a
dual banana to BNC adapter for
use with multimeters with 4 mm
(0.16 in) banana input plugs.
This clamp is optimized for mea-
surement on power distribution
systems.
Current range: 1 A to 3000 A
Frequency range: 10 Hz to
100 kHz
Safety rating: CAT III 600 V
i3000s Flex-24 or -36
AC Current Clamp
The flex clamp uses the Rogowski
(air-cored coil) principle and can
be used to measure three ranges
of currents up to 3000A when
used in conjunction with oscillo-
scopes, recorders or data loggers.
The flexible and lightweight
measuring head allows quick
and easy installation in hard-to-
reach areas without batteries or
an external power source. This
clamp fits around large conductors
and is available in 610mm and
914mm (24 in and 36 in) lengths.
Current range: 30 A, 300 A, and
3000 A switchable
Frequency range: 10 Hz to
50 kHz
Safety rating: CAT III 600 V
i3000s Flex-24 is available
in a convenient four-pack
(i3000s Flex 4 Pack)
i5s AC Current Clamp
This compact 5A ac clamp,
specially configured to provide
low-current accuracy while
taking measurements on sec-
ondary current transformers,
expands the use of the Fluke
430 Series Three-Phase Power
Quality Analyzer.
Current range: 10 mA to 5 A
Frequency range: 40 Hz to
5kHz
Safety rating: CAT III 600V (for
insulated conductors only)
Also available in a convenient
three-pack (i5sPQ3)
i6000s Flex-24 or -36
AC Current Clamp
This ac current clamp utilizes the
Rogowski (air-cored coil) principle
and measures three ranges of cur-
rents up to 6000A when used in
conjunction with oscilloscopes,
recorders, or data loggers. The
flexible and lightweight mea-
suring head allows quick and
easy installation in hard-to-reach
areas without batteries or an
external power source. This clamp
fits around large conductors and
is available in both 610 mm and
914mm (24 in and 36 in) lengths.
Current range: 60 A, 600 A,
and 6000 A switchable
Frequency range: 10 Hz to
50 kHz (-3dB)
Safety rating: CAT III 600 V
i2000
i3000s
i3000s Flex-24 and -36
i5S
i6000s
i1000s
23
For more information, go to www.fluke.com/accessories
Current clamps: AC
Current clamps: AC/DC
i30 i30s 80 i -110 s i310s i410 i1010
DC range 30 mA to 30 A 30 mA to 30 A 0.1 A to 100 A 0.1 A to 300 A 1 A to 400 A 1 A to 1000 A
AC range 30 mA to 20 A rms 30 mA to 20 A rms 0.1 A to 70 A 0.1 A to 300 A 1 A to 400 A 1 A to 600 A
Accuracy ± 1 % of reading,
± 2 mA
± 1 % of reading,
± 2 mA
0.1 A to 10 A;
dc to 1 kHz:
± 3 % + 50 mA;
up to 100 A
add 15 %;
up to 20 kHz
add 12 %
30 A range:
1 % + 50 mA
300 A range:
1 % + 300 mA
3.5 % + 0.5 A
for dc or ac
(45 Hz to 400 Hz)
2 % + 0.5 A
for dc or ac
(45 Hz to 400 Hz)
Bandwidth (-3 dB) dc to 20 kHz
(-0.5 dB)
dc to 100 kHz
(-0.5 dB)
100 kHZ dc to 20 kHz 3 kHz 10 kHz
Zero error
adjustment
Yes Yes Yes Yes Yes Yes
Maximum
conductor
diameter
19 mm
(0.75 in)
19 mm
(0.75 in)
11.8 m m
(0.46 in)
19 mm
(0.75 in)
30 mm
(1.18 in)
30 mm
(1.18 in)
Maximum
conductor size
250 MCM 250 MCM 1 AWG 250 MCM 750 MCM or
2-500 MCM
750 MCM or
2-500 MCM
Output levels 100 mV/A 100 mV/A 10 mV/A, 100 mV/A 10 mV/A, 1 mV/A 1 mV/A 1 mV/A
Output cable 1.5 meter with
shrouded dual
banana plug
2 meter with BNC
termination
1.6 meter with BNC
termination
2 meters with BNC
termination and a BNC
to safety shrouded
banana adapter
1.2 meter with
shrouded banana
plugs
1.2 meter with
shrouded banana
plugs
Battery life (hours) 30 30 40 30 60 60
Warranty One-year One-year One-year One-year One-year One-year
Safety CAT III 300 V CAT III 300 V CAT II 600 V,
CAT III 300 V
CAT III 300 V CAT III 600 V CAT III 600 V
AC/DC current clamp specifications
24
i1010
Model number 80i-110s i410 i1010 i30 i30s i310s
10/11/12/
12B/16/18
0.1 A to 100 A dc/
0.1 A to 70 A ac*
5 A to 400 A dc/
7 A to 400 A ac
5 A to 1000 A dc/
7 A to 600 A ac
40 mA to 30 A dc/
60 mA to 20 A ac
40 mA to 30 A dc/
60 mA to 20 A ac
0.4 A to 450 A dc/
0.6 A to 300 A ac
110/111/112 0.14 A to 100 A dc/
3 A to 70 A ac*
5 A to 400 A dc/
300 A to 400 A ac
5 A to 1000 A dc/ 300
A to 600 A ac
40 mA to 30 A dc/
3 A to 20 A ac
40 mA to 30 A dc/
3 A to 20 A ac
0.4 A to 450 A dc/
30 A to 300 A ac
114/115/116/117 0.1 A to 100 A dc/
0.1 A to 70 A ac*
1.4 A to 400 A dc/
6 A to 400 A ac
1.4 A to 1000 A dc/
6 A to 600 A ac
30 mA to 30 A dc/
60 mA to 20 A ac
30 mA to 30 A dc/
60 mA to 20 A ac
0.1 A to 450 A dc/
0.6 A to 300 A ac
21/23/70/73/
75/77 Series III
0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
5 A to 400 A ac
1 A to 1000 A dc/
5 A to 600 A ac
30 mA to 30 A dc/
40 mA to 20 A ac
30 mA to 30 A dc/
40 mA to 20 A ac
0.1 A to 450 A dc/
0.4 A to 300 A ac
26/79 Series III 0.1 A to 100 A dc/
0.2 A to 70 A ac*
1 A to 400 A dc/
20 A to 400 A ac
1 A to 1000 A dc/
20 A to 600 A ac
30 mA to 30 A dc/
200 mA to 20 A ac
30 mA to 30 A dc/
200 mA to 20 A ac
0.1 A to 450 A dc/
2 A to 300 A ac
27 0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
1 A to 400 A ac
1 A to 1000 A dc/
1 A to 600 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
0.1 A to 450 A dc/
0.1 A to 300 A ac
77-IV 0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
5 A to 400 A ac
1 A to 1000 A dc/
5 A to 600 A ac
30 mA to 30 A dc/
40 mA to 20 A ac
30 mA to 30 A dc/
40 mA to 20 A ac
0.1 A to 450 A dc/
0.4 A to 300 A ac
175/177/179 0.11 A to 100 A dc/
0.3 A to 70 A ac*
1.6 A to 400 A dc/
30 A to 400 A ac
1.6 A to 1000 A dc/
30 A to 600 A ac
30 mA to 30 A dc/
300 mA to 20 A ac
30 mA to 30 A dc/
300 mA to 20 A ac
0.1 A to 450 A dc/
3 A to 300 A ac
1577/1587 0.1 A to 100 A dc/
0.3 A to 70 A ac*
1.2 A to 400 A dc/
30 A to 400 A ac
1.2 A to 1000 A dc/
30 A to 600 A ac
30 mA to 30 A dc/
300 mA to 20 A ac
30 mA to 30 A dc/
300 mA to 20 A ac
0.1 A to 450 A dc/
3 A to 300 A ac
83-III/83-V/88-V 0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
1 A to 400 A ac
1 A to 1000 A dc/
1 A to 600 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
0.1 A to 450 A dc/
0.1 A to 300 A ac
85-III/87-III/87-V 0.1 A to 100 A dc/
0.2 A to 70 A ac*
1 A to 400 A dc/
20 A to 400 A ac
1 A to 1000 A dc/
20 A to 600 A ac
30 mA to 30 A dc/
200 mA to 20 A ac
30 mA to 30 A dc/
200 mA to 20 A ac
0.1 A to 450 A dc/
2 A to 300 A ac
87-IV/89-IV/
187/189
0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
2.5 A to 400 A ac
1 A to 1000 A dc/
2.5 A to 600 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
0.1 A to 450 A dc/
0.25 A to 300 A ac
287/289 0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
1 A to 400 A ac
1 A to 1000 A dc/
1 A to 600 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
0.1 A to 450 A dc/
0.1 A to 300 A ac
8060A/8062A 0.1 A to 100 A dc/
0.2 A to 70 A ac*
1 A to 400 A dc/
20 A to 400 A ac
1 A to 1000 A dc/
20 A to 600 A ac
30 mA to 30 A dc/
200 mA to 20 A ac
30 mA to 30 A dc/
200 mA to 20 A ac
0.1 A to 450 A dc/
2 A to 300 A ac
860 Series 0.1 A to 100 A dc/
0.3 A to 70 A ac*
1 A to 400 A dc/
30 A to 400 A ac
1 A to 1000 A dc/
30 A to 600 A ac
30 mA to 30 A dc/
300 mA to 20 A ac
30 mA to 30 A dc/
300 mA to 20 A ac
0.1 A to 450 A dc/
3 A to 300 A ac
39/41B Usable but will read 10
or 100 times higher
1 A to 400 A ac**
Not spec’d for dc
1 A to 600 A ac**
Not spec’d for dc
Usable but will read
100 times higher**
Usable but will read
100 times higher
Not spec’d for dc
0.6 A to 300 A ac
9X Series 0.1 A to 100 A dc/
0.1 A to 70 A ac
1 A to 400 A dc/
5 A to 400 A ac**
1 A to 1000 A dc/
5 A to 600 A ac**
30 mA to 30 A dc/
50 mA to 20 A ac**
30 mA to 30 A dc/
50 mA to 20 A ac
0.1 A to 450 A dc/
0.5 A to 300 A ac
120 Series 0.1 A to 100 A dc/
0.1 A to 70 A ac
1 A to 400 A dc/
25 A to 400 A ac**
1 A to 1000 A dc/
25 A to 600 A ac**
30 mA to 30 A dc/
250 mA to 20 A ac**
30 mA to 30 A dc/
250 mA to 20 A ac
0.1 A to 300 A dc/
0.1 A to 300 A ac
190 Series 0.1 A to 100 A dc/
0.1 A to 70 A ac
1 A to 400 A dc/
5 A to 400 A ac**
1 A to 1000 A dc/
5 A to 600 A ac**
30 mA to 30 A dc/
50 mA to 20 A ac**
30 mA to 30 A dc/
50 mA to 20 A ac
0.1 A to 300 A dc/
0.1 A to 300 A ac
45 DMM 0.1 A to 100 A dc/
0.15 A to 70 A ac*
1 A to 400 A dc/
15 A to 400 A ac
1 A to 1000 A dc/
15 A to 600 A ac
30 mA to 30 A dc
150 mA to 20 A ac
30 mA to 30 A dc
150 mA to 20 A ac
0.1 A to 450 A dc/
1.5 A to 300 A ac
8808A 0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
2 A to 400 A ac
1 A to 1000 A dc/
2 A to 600 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
0.1 A to 450 A dc/
0.2 A to 300 A ac
8845A/8846A 0.1 A to 100 A dc/
0.1 A to 70 A ac*
1 A to 400 A dc/
1 A to 400 A ac
1 A to 1000 A dc/
1 A to 600 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
30 mA to 30 A dc/
30 mA to 20 A ac
0.1 A to 450 A dc/
0.1 A to 300 A ac
705/707 0.1 A to 100 A dc,
no ac*
4 A to 400 A dc, no ac 4 A to 1000 A dc, no ac 40 mA to 30 A dc, no ac 40 mA to 30 A dc, no ac 0.4 A to 450 A dc, no ac
715 0.1 A to 100 A dc,
no ac*
4 A to 400 A dc, no ac 4 A to 1000 A dc, no ac 40 mA to 30 A dc, no ac 40 mA to 30 A dc, no ac 0.1 A to 450 A dc, no ac
74X Series 0.1 A to 100 A dc/
1.1 A to 70 A ac*
1 A to 400 A dc/
110 A to 400 A ac
1 A to 1000 A dc/
110 A to 600 A ac
30 mA to 30 A dc/
1.1 A to 20 A ac
30 mA to 30 A dc/
1.1 A to 20 A ac
0.1 A to 450 A dc/
11 A to 300 A ac
787/789 0.1 A to 100 A dc/
0.2 A to 70 A ac*
1 A to 400 A dc/
20 A to 400 A ac
1 A to 1000 A dc/
20 A to 600 A ac
30 mA to 30 A dc/
200 mA to 20 A ac
3 mA to 30 A dc/
200 mA to 20 A ac
0.1 A to 450 A dc/
2 A to 300 A ac
*Requires PM9081/001 Adapters. **Requires PM9082/001 Adapter
AC/DC clamp-on current probe compatibility
25
For more information, go to www.fluke.com/accessories
Left to right: i410, 80i-110s, i30
AC/DC clamps
AC/DC current clamps are available for a range of applications and professions.
i410 AC/DC Current Clamp
This battery-powered Hall-effect
probe measures 1A to 400A
with large-claw clamp that gives
access to difficult-to-reach areas.
It is compatible with most mul-
timeters and other devices that
measure ac and dc current and
accepts shrouded 4mm (0.16in)
banana plugs.
On/Off LED indicator
AC and dc current range:
1 A to 400 A
Frequency range: 3 kHz
Safety rating: CAT III 600 V
i410-KIT AC/DC Current
Clamp and Carry Case Kit
This special-value kit for elec-
trical professionals adds ac and
dc current measurement capa-
bilities to a digital multimeter.
A roomy carrying case holds a
meter and the current clamp plus
test leads, probes and manuals.
Kit includes:
i410 AC/DC Current Clamp
C116 Soft Carrying Case
i1010 AC/DC Current Clamp
This clamp measures both ac and
dc currents with a large-jaw, bat-
tery-powered Hall-effect probe
that gives access to difficult-
to-reach areas. It is compatible
with most Fluke multimeters and
any other devices that measure
ac and dc current and accept
shrouded 4mm (0.16 in) banana
plugs.
On/Off LED indicator
AC current range: 1 A to
600 A ac
DC current range: 0.5 A to
1000 A dc
Frequency range: dc to 10 kHz
Safety rating: CAT III
600 V rms
i1010-Kit AC/DC Current
Clamp and Carry Case Kit
This special-value kit for elec-
trical professional adds ac and dc
current measurement capabilities
to a digital multimeter. A roomy
carrying case holds a meter and
the current clamp plus test leads,
probes and manuals. Kit includes:
i1010 AC/DC Current Clamp
C116 Soft Carrying Case
80i-110s AC/DC
Current Clamp
This clamp is compatible with
ScopeMeter, power harmonics
analyzer, multimeter, or other
voltage measurement device that
has BNC input connectors.
AC current range: 0.1 A to 70 A
DC current range: 0.1 A to
100 A
Frequency range: 1 Hz to
100 kHz
Optional PM9081/001 Dual
Banana Plug Male to Female
BNC Adapter is available for
digital multimeters
Safety rating: CAT II 600 V
i30 AC/DC Current Clamp
Based on Hall-effect technology,
this battery-powered clamp mea-
sures both ac and dc current. It
may be used in conjunction with
multimeters, recorders and other
suitable recording instruments
for accurate non-intrusive current
measurement.
AC current range: 30 mA to
20A rms
DC current range: 30 mA to
30 A
Frequency range: dc to
20 kHz (-0.5 dB)
Safety rating: CAT III 300 V
i30s AC/DC Current Clamp
Based on Hall effect technology,
this battery-powered clamp mea-
sures both ac and dc current. It
may be used with ScopeMeter
and other suitable recording
instruments for accurate non-
intrusive current measurement.
AC current range: 30 mA to
20 A rms
DC current range: 30 mA to
30 A
Frequency range: dc to
100 kHz (-0.5 dB)
Safety rating: CAT III 300 V
i410 i1010
i410-KIT i1010-Kit
26
Current clamps: AC/DC
i310s AC/DC Current Clamp
Based on Hall-effect technology,
this battery-powered clamp mea-
sures both ac and dc current. It
may be used with ScopeMeter
and other suitable recording
instruments for accurate non-
intrusive current measurement.
This clamp is especially useful
for current measurements on
inverters, switching power sup-
plies, industrial controllers,
automotive diagnostics, and
other applications requiring
current measurements and/
or waveform analysis.
AC current range:
0.1 A to 300 A
DC current range:
0.1 A to 300 A
Frequency range: dc to 20 kHz
Safety rating: CAT III 300 V
Did you know?
Does your current probe
read zero current when you
clamp it around a power
cord? Thats because the
power cord has both the hot
and neutral current carrying
wire in it. If both wires are
in the jaws of the clamp
meter, the fields cancel each
other out, and the current
clamp will read nothing. You
need to put just one current-
carrying conductor in the
jaw of the current clamp. If
you don’t have access to the
separate wires within the
cord, use a line splitter tool
to avoid breaking the circuit.
i30
8 0 i -110 s
i30s
i310s
27
For more information, go to www.fluke.com/accessories
Current clamps: AC/DC
Model number C23 C25
CAMO
-C25 C33 C35 CAMO
-C37 C43 C50 C75 C90 C115 C116 C150 C280 C345 C550 C781 C789
114/115/116/117
For multiple test leads and accessories
For multiple meters, test leads and accessories
For multiple meters, test leads and accessories
175/177/179
187/189
287/289 • •
27 II/28 II • • • •
61
77 IV • • • • • • • •
83V/87V/88V • • • •
233 • • • • •
323/324/325 • • •
373/374/375/
376/902 • •
353/355
365
1503/1507/1577/1587 • • • •
9040/9062 • •
430/1735/1740 Series
43B/120 Series • •
190 Series
51/52/53/54 II • • • •
570 Series
705/707 • •
712/714/715/717 • • • •
718 • •
724/725/726 • • • •
753/754 • •
787 • • • • • •
789 • • • •
922 • • •
971 •••
T5/T+/T+Pro • •
T90/T110/T130/T150
VT02/VT04/VT04A
28
Cases, holsters, and hangers
Soft cases compatibility
H5
29
For more information, go to www.fluke.com/cases
CXT
Hard cases compatibility
Model number
Hard cases Leather cases Holsters Hangers
C20 C100 C101 CXT80 CX T170 CXT280 CXT1000 C800 C1600 C510 C520A H80M H3 H5 H6 H15 ToolPak
114/115/116/117
For multiple meters, accessories and other tools
For multiple meters, accessories and other tools
175/177/179 • •
187/189 • •
27 II/28 II • • •
61
77 IV • •
83V/87V/88V • •
233 • •
287/289 • •
323/324/325 • •
373/374/375/376/902 • •
1503/1507/1577/1587 • •
9040/9062 • •
1735/1740 Series
430 Series
43B/120 Series
190 Series
922
971
51/52/53/54 II • •
561
705/707
712/714/715/717 • • 715
718
724/725/726 • •
787 • •
789 • •
T5/T+/T+Pro T+/
T+Pro
T90/T110/T130/T150 • •
CAMO-C25 Camouflage
Carrying Case
Zippered carrying case with pad-
ding and inside pocket for holding
accessories.
High quality 1000D fabric
Dimensions (HxWxD):
20.3 cm x 12.1 cm x 4.6 cm
(8 in x 4.8 in x 1.8 in)
C33 Soft Carrying Case
Zippered carrying case with
durable vinyl exterior and belt
loop. Inner pocket stores test
leads and small accessories.
Made of polyester
Dimensions (HxWxD):
280 mm x 115 mm x 55 mm (11
in x 4.5 in x 2.2 in)
C35 Soft Carrying Case
Case top opens laterally to allow
use of test tool without removing
it from the case and includes a
Velcro® strap to secure the test
tool.
Made of durable polyester 600D
Dimensions (HxWxD):
220 mm x 140 mm x 65 mm
(8.7 in x 5.5 in x 2.6 in)
CAMO-C37 Camouflage
Carrying Case
Zippered carrying case with inner
pocket for storing test leads and
small accessories.
High quality 1000D fabric
Dimensions (HxWxD):
26.5 cm x 9 cm x 3 cm
(10.5 in x 3.5 in x 1.2 in)
C43 Soft Carrying Case
Zippered carrying case includes
inner front pocket with closure
and two pockets to store test
leads or small accessories.
Includes detachable 254 mm
(10in) handle and 1066 mm
(42in) shoulder strap.
Made of durable polyester 600D
Dimensions (HxWxD):
318 mm x 230 mm x 90 mm
(12.5 in x 9.1 in x 3.5 in)
C50 Meter Case
Zippered and padded case fea-
turing an inside strap to secure
a meter as well as a belt loop for
convenient carrying. Also includes
an inside pocket for holding
accessories.
Made of polyester
Dimensions (HxWxD):
192 mm x 90 mm x 38 mm
(7.56 in x 3.5 in x 1.5 in)
C75 Accessory Case
Zippered carrying case designed
for carrying small accessories.
Includes two inside pockets.
Made of polyester
Dimensions (HxWxD):
179 mm x 103 mm x 26 mm
(7 in x 4 in x 1 in)
C90 Soft Case for DMMs
Zippered carrying case featuring
a belt loop. Also includes padding
to protect the meter and an inside
pocket for holding accessories.
Made of polyester
Dimensions (HxWxD):
205 mm x 90 mm x 72 mm
(8 in x 3.5 in x 2.8 in)
C35
C25
C115 C280
C116
Soft cases
C12A Meter Case
Zippered case with inside
pockets and belt loop for
convenient carrying.
Made of polyester
Dimensions (HxWxD):
172 mm x 128 mm x 38 mm
(6.8 in x 5 in x 1.5 in)
C23 Soft Carrying Case
Zippered case featuring a belt
loop for convenient carrying
and an inner pocket to store test
leads or small accessories.
Made of durable vinyl
Ideal companion case to:
Fluke 61 and 65 Infrared
Thermometers
Fluke 321 and 322 Clamp
Meters
Dimensions (HxWxD):
225 mm x 95 mm x 58 mm
(8.9 in x 3.75 in x 2.3 in)
C25 Large Soft Case
for DMMs
Zippered carrying case with
padding and inside pocket for
holding accessories.
Made of polyester
Dimensions (HxWxD):
218 mm x 128 mm x 64 mm
(8.6 in x 5 in x 2.52 in)
C345
30
Cases, holsters, and hangers
C115 Soft Carrying Case
Includes two padded pockets
for protection of two test tools,
such as a digital multimeter and
60 Series IR Thermometer and
a pouch for test leads and other
accessories.
Made of durable polyester 600D
Dimensions (HxWxD):
240 mm x 205 mm x 75 mm
(9.5 in x 8 in x 3 in)
C116 Soft Carrying Case
Provides adjustable padded space
with a moveable Velcro® divider
for protection of two test tools,
such as a digital multimeter and a
current probe.
Made of durable polyester 600D
Dimensions (HxWxD):
240 mm x 230 mm x 65 mm
(9.5 in x 9 in x 2.6 in)
C150 Soft Carrying Case
Zippered carrying case with inner
pocket for storing test leads and
small accessories.
High quality 1000D fabric
Dimensions (HxWxD):
29.8 cm x 11.4 cm x 5.6 cm
(11.75 in x 4.5 in x 2.2 in)
C280 Soft Case
Designed especially for larger
format test tools such as the
new Fluke 287 and 289 Digital
Multimeters. Includes detachable,
extendable shoulder strap and an
inner front pocket with closure
and dual pouch pockets for test
tools and accessories.
Made of durable polyester 600D
Dimensions (HxWxD):
230 mm x 185 mm x 65 mm
(9 in x 7.3 in x 2.6 in)
C345 Soft Case
The perfect case for carrying a
wide range of Fluke handheld
test tools and accessories, large
enough for all your accessories
and instrument manuals. Includes
an elastic accessory strap and
mesh accessory retainer as well
as an outer pouch, outer zipper
packet and two slash pockets for
convenient accessory storage.
Made of durable polyester 600D
Dimensions (HxWxD):
360 mm x 200 mm x 240 mm
(14 in x 8 in x 9.5 in)
C570 Soft Case
Designed specifically for the
larger IR thermometers like
the Fluke 560 and 570 Series.
Includes zippered holster and
padding to protect test tools as
well as convenient belt loops and
clips.
Made of polyester
Dimensions (HxWxD):
240 mm x 89 mm to 170 mm x
56 mm (9.5 in x 3.5 in to 6.7in
x 2.2 in)
C550 Tool Bag
Rugged, weather-resistant tool
bag with zippered top, inside
pockets and carrying straps.
Features a large storage compart-
ment with 25 pockets as well as
steel-reinforced frame.
Made of ballistic cloth with
heavy-duty hardware
Dimensions (HxWxD):
333 mm x 513 mm x 231 mm
(13 in x 20.2 in x 9.1 in)
C781 Meter Case
Zippered case, designed for
carrying a meter as well as a
detachable external pouch for
holding test leads, and other
accessories.
Made of durable polyester 600D
Dimensions (HxWxD):
269 mm x 141 mm x 90 mm
(10.6 in x 5.6 in x 3.5 in)
C345
C50 C12A
C550
C150
C33C90 C75
CAMO-C25 CAMO-C37
C570
C43 C23
C781
31
For more information, go to www.fluke.com/accessories
Cases, holsters, and hangers
Hard cases
C101 Hard Case
Tough polypropylene case with
configurable diced foam interior
to store and protect tools and
accessories.
Exterior dimensions (HxWxD):
305 mm x 360 mm x 105 mm
(12 in x 14.2 in x 4.1 in)
Interior dimensions (HxWxD):
230 mm x 290 mm x 65 mm
(9 in x 11.5 in x 2.5 in)
C100 Universal
Carrying Case
Large, tough polypropylene case
with carrying handle and snap-
on lid. This case conveniently
carries tools, leads, and other
accessories.
Dimensions (HxWxD):
397 mm x 346 mm x 122 mm
(15.7 in x 13.6 in x 4.8 in)
C20 Hard Case
Heavy-duty construction with
carrying handle and storage
compartment, designed to hold a
meter and accessories. It features
a top cover that snaps onto the
back to serve as a tilt stand.
Made of polyprophylene
Dimensions (HxWxD):
256 mm x 154 mm x 106 mm
(10 in x 6.1 in x 4.2 in)
C800 Meter and
Accessory Case
Tough polypropylene case
with a sturdy handle, snap-on
detachable lid, and convenient
compartments for holding acces-
sories and manuals.
Dimensions (HxWxD):
230 mm x 385 mm x 115 mm
(9 in x 15 in x 4.5 in)
C101
CXT
C100
VT04-HARD CASE
C20 C800
CXT Extreme Cases Series
New! CXT1000: for multiple
meters, accessories and other
test tools (Dimensions (HxWxD):
34.3 cm x 46.5 cm x 17.8 cm
(13.5 in x 18.3 in x 7 in)
CXT1000 features a diced foam
interior for custom storage con-
figuration
Unbreakable, watertight, air-
tight, dust proof, chemical
resistant and corrosion proof
Offers maximum protection for
your digital multimeters and
accessories against high impact,
vibration or shock
Includes an automatic purge
valve for quick equalization
after changes in atmospheric
pressure
CXT80: for use with 87V, 80
Series, 187/189, 27 II/28 II Digi-
tal Multimeters
CXT170: for use with 170 Series,
114/115/116/117, 77 III, and 77
IV Digital Multimeters
CXT280: for use with 287 or
289 True-rms Logging
Multimeters
Dimensions (HxWxD):
27.9 x 31.8 x 12.7 cm
(11 x 12.5 x 5 in)
VT04-HARD CASE
Hard case for all Fluke Visual IR
Thermometers.
C789
C789 Meter and
Accessory Case
Large carrying case with three
compartments, removable handle,
and shoulder strap. Holds a meter
and multiple accessories.
Made of durable polyester 600D
Dimensions (HxWxD):
308 mm x 256 mm x 77 mm
(12 in x 10 in x 3 in)
CXT1000
32
Cases, holsters, and hangers
C1600 Gear Box for meter
and accessories
A rugged, molded plastic case
with a deep interior and lift-
out tray designed to carry Fluke
handheld digital multimeters and
process calibrators, as well as
their accessories. Features a large
handle and snap-open lid com-
partment for easy access
to small parts such as fuses, bat-
teries, probes, and leads.
Can also be locked.
Includes five hook and loop
straps to wrap cords and test
leads
Dimensions (HxWxD):
260 mm x 390 mm x 200 mm
(10 in x 15 in x 7.8 in)
Leather cases
C520A Leather Tester Case
Rugged leather case designed
to hold Fluke electrical testers.
It features a large belt loop and
a top flap to secure the tester.
Made of top-grain cowhide with
heavy-duty stitching and rein-
forced rivets.
Dimensions (HxWxD):
256 mm x 154 mm x 106 mm
(10 in x 6 in x 4 in)
C510 Leather Meter Case
Rugged leather case designed to
hold most Fluke digital multime-
ters, thermometers, and process
calibrators. It features a large belt
loop and a top flap to secure the
tool. Made of top-grain cowhide
with heavy-duty stitching and
reinforced rivets.
Dimensions (HxWxD):
287 mm x 179 mm x 106 mm
(11 in x 7 in x 4 in)
Holsters
H5 Electrical
Tester Holster
Rugged fabric holster designed to
hold Fluke T3 and T5 Electrical
Testers. It features a built-in
belt loop and flap for test lead
storage.
Dimensions (HxWxD):
192 mm x 90 mm x 38 mm
(7.5 in x 3.5 in x 1.5 in)
H3 Clamp Meter Holster
Rugged fabric holster designed
to hold Fluke 330 Series Clamp
Meters. It features a built-in belt
loop and a handy pocket with
snap for test lead storage.
Dimensions (HxWxD):
231 mm x 90 mm x 64 mm
(9 in x 3.5 in x 2.5 in)
New! H15 Electrical
Tester Holster
Rugged fabric holster designed to
hold Fluke T90, T110, T130 and
T150 Two-Pole Testers.
High quality 1000D fabric
Dimensions (HxWxD):
27.9 cm x 9.2 cm x 5.1 cm
(11 in x 3.6 in x 2 in)
H80M Protective
Holster with Magnetic
Hanging Strap
Convenient snap-on holster
with a magnetic hanging system
enables hands-free work while
protecting digital multimeters or
calibration tools. This holster is
designed to absorb shock and to
hang from just about any metal
surface.
Includes a hanging magnet,
general purpose hanger, and
hook and loop straps
Dimensions (HxWxD):
190 mm x 95 mm x 43 mm
(7.5 in x 3.7 in x 1.7 in)
C10 Meter Holster
Snap-on holster absorbs shocks
and protects multimeters from
rough handling. It features a
built-in stand and hanger loop for
convenience during testing.
Compatible with Fluke 10
Series Multimeters
Dimensions (HxWxD):
154 mm x 77 mm x 45 mm
(6 in x 3 in x 1.8 in)
H6 Infrared
Thermometer Holster
Durable nylon construction with
Velcro® closures provides quick
access and protection for infrared
thermometers. It features a snap-
open loop that attaches easily to
a belt and an accessory pocket
for storing temperature probes.
Dimensions (HxWxD):
302 mm x 178 mm x 57 mm
(11.9 in x 7 in x 2 in)
C520A C510 H5 H3 H6
H80M
H15
C10
33
For more information, go to www.fluke.com/accessories
Cases, holsters, and hangers
Hangers
TPAK ToolPakMagnetic Meter Hanger
Hang your meter in a variety of ways for
convenient hands-free operation.
Kit includes:
Magnetic hanger
Powerful (rare earth) magnetic hanger, firmly
attaches to any metal surface
Allows customers to conveniently hang meter to
conduct test and increase productivity
Hook hanger
For hanging on non-magnetic surfaces
Hook lip over protruding edge allows hands
free operation
General purpose hanger
Safely hang meter on a nail or screw
Clips in the top of most Fluke multimeters
Hook loop strap
Nine-inch hook and loop strap allows to conve-
niently loop strap around pipe or conduit
Makes it easy and more convenient to take
measurements
One-year warranty
Attaches to back of many Fluke meters,
including 110, 170, 180, 280 Series, 87V and
83V DMMs, 724, 725 and 789 Process Calibrators,
70 Series III DMMs, 1503, 1507, 1577 and 1587
Insulation Multimeters and 50 Series II Digital
Thermometers.
TPAK
34
Cases, holsters, and hangers
Vibration and alignment
Fluke 805
Vibration Meter
805ES External Sensor
Assembly
Allows access into tight or
crowded spaces where it might
otherwise be difficult to take a
vibration measurement.
Fluke 810
Vibration Tester
810QDC Quick Disconnect
Cable
Eight-foot quick-disconnect cable
connects the triaxial vibration
sensor.
810SC-20 Sensor Cable
20-foot cable connects the
triaxial vibration sensor to the
Fluke 810 Vibration Tester. (plugs
into the one foot Quick Disconnect
cable section)
810S Triaxial Vibration
Sensor for 810
Triaxial vibration sensor captures
vibration data in all three primary
axes simultaneously for faster,
more accurate data collection.
810SMM Sensor Magnetic
Mounts
High-power magnet
attaches firmly to motors
and machinery
Parallel magnet tips engage
both flat and cylindrical
surfaces
810SMP Sensor mounting
pads for vibration sensors
(pack of 10)
10-pack of Sensor Mounting Pads
provide standardized sensor
attachment points on critical
equipment.
810T Tachometer
Precision laser tachometer for
measuring the exact speed of
equipment, such as variable-fre-
quency drives (VFD) to determine
the running speed under varying
load conditions.
810PA Charger for
battery pack
Recharge the Fluke 810 Smart
Battery Pack—including interna-
tional outlet adapters.
SBP810, Smart battery pack
for 810
Lithium-Ion Battery pack provides
8-hours of runtime under normal
operating conditions.
Fluke 830 Laser
Alignment Tool
830/MAGNET Magnetic
Mounting Bracket Set
High-power magnets attach
firmly to shaft couplings
Narrow profile can mount on
equipment with little clearance
between the coupling and the
machine housing
Ideal for large-diameter cou-
plings or for the simplest, most
rapid set-ups
830/SHIMS Precision Shim
Kit, Sizes A&B, Metric
An essential step in most shaft
alignment procedures is to adjust
the vertical height of the machine
by adding or removing precision
shims from beneath the mounting
feet of the machinery.
830/SHIMS
810SMP 830/MAGNET
For more information, go to www.fluke.com/accessories
35
Left to right: 3533001, 810 Tachometer, 810SMM, 810S, 810QDC
LVD2
LVD1 1AC II 2AC
36 LVD2 Volt Light
Non-contact ac voltage detector
and LED flashlight combined into
an easy-to-use pen-style design
with dual-sensitivity. This voltage
detector glows blue when 3 cm
to 12 cm (1 in to 5 in) from ac
voltage and red when at the
source. For use in commercial and
industrial applications.
Detects voltage from 90 V to
600 V ac
Ultra-bright white LED light
with 100,000 hour bulb life
AAA battery included
Safety rating: CAT IV 600 V
LVD1 Volt Light
Non-contact ac voltage detector
and pocket-sized flashlight
combined with exclusive dual-
sensitivity. This voltage detector
glows blue when 2.5cm to
12.7cm (1 in to 5 in) from ac
voltage and red when at the
source.
Detects voltages from 40 V to
300 V ac
Ultra-bright white LED with
100,000 hour bulb life
AAA battery included
1AC II VoltAlert
non-contact voltage
detector
Voltbeat technology and con-
tinuous self-test—so you always
know its working
Upon detection, tip glows and
beeper sounds
CAT IV 1000 V for added
protection
Expanded range: 90 V ac to
1000 V ac
On/Off button
Two-year warranty
2AC VoltAlert
non-contact voltage
detector
Always on, using special
low power circuitry to sustain
battery life and always ready
to use
Innovative “Battery Check
button function ensures
battery is in good condition*
CAT IV 1000 V overvoltage
rated product for best in class
user protection
Expanded range: 90 V ac to
1000 V ac
Fluke ruggedness and
reliability
Two-year warranty
* Use of Battery Check function is optional
and for convenience only, it is not intended
as a substitute for checking the unit on a
known live source before and after use.
Lights and voltage detectors
L200
L206
L205
L210
L207
L211
L200 L215
37
For more information, go to www.fluke.com/accessories
L200 Probe Light
Small, rugged light that easily
attaches to any Fluke test probe,
illuminates the contact area and
frees hands for work.
Bright white LED with 120
hours of battery life
Two 3 V watch batteries
included
L205 Mini Hat Light
Rugged, high-intensity Xenon
work light with pre-focused
optical-quality reflector attaches
to a baseball cap to allow hands-
free work. (Hat not included.)
Includes waterproof ABS case
that won’t crack or chip
Two AAA batteries included
L206 Deluxe LED Hat Light
Attach this water-resistant light
to a hard hat, a baseball hat, or
even a panel door for hands-
free bright light where needed.
Includes a 360° rotating clip,
special hard-hat attachment, and
neck lanyard. (Hat not included.)
Three LEDs with 40-hour
battery life
Three AAA battery included
L207 High Intensity Light
with Collector’s Cap
Powerful, lightweight, mini-
Xenon light illuminates work area
to free hands for work. Comes
with Limited Edition Fluke collec-
tors cap that adjusts for all-day
comfort. Waterproof, rugged light
attaches to bill of baseball cap.
Xenon high intensity work light
Two AAA batteries included
L210 Probe Light Kit
Test probe extender with small,
bright LED that illuminates the
contact area and frees hands
for work. Two probe extenders
20cm (8 in) fit modular test
probes and keep hands away
from live circuits. Ultra-bright
white LED provides 120 hours
of battery life. Kit includes:
L200 Probe Light
SureGrip test probe
extenders
Two 3 V watch batteries
included
Probe extenders safety rating:
CAT III 1000 V, 10 A
L211 Probe Light Kit
This special-value combo pairs
the new L200 Probe Light with
one of the most popular test
leads by Fluke and a handy car-
rying case. Probe light attaches
to any Fluke test probe to
free both hands for work. Kit
includes:
L200 Probe Light
TL71 Premium Test Lead Set
C75 Accessory Case
L215 SureGrip Kit
with Probe Light and
Probe Extender
A great complement of industrial
test accessories with a small,
rugged light that attaches to test
probe or extenders to illuminate
the contact area. Kit includes:
L200 Probe Light
SureGrip Test Probe
Extenders, 20 cm (8 in)
TP220 SureGrip Industrial Test
Probes
TL224 SureGrip Insulated Test
Leads
Foldable soft pouch with
six pockets and hook & loop
closure
Safety rating:
TP220: CAT II 1000 V, 10 A.
(CAT III 1000 V, CAT IV
600 V with protective cap)
TL224: CAT III 1000 V,
CAT IV 600 V, 10 A
Probe extenders: CAT III
1000 V, 10 A
Lights and voltage detectors
Infrared cameras
Sun visors
Tripod
bases
Infrared lenses and
battery chargers
FC WIFI SD Card
Fluke Connect® WiFi SD Card
Wirelessly enable your Fluke infrared camera with the Fluke Connect wireless SD card and
you can instantly upload, share and analyze data from anywhere, with anyone on your
team, at any time.
Works with Ti90, Ti95, Ti100, Ti105, Ti110, Ti125, TiR105, TiR110 and TiR125
38
Model number
Ti400/Ti300/
Ti200 Ti450/Ti480
TiX500/
TiX520
TiX560/
TiX580
TiX620/
TiX640
TiX660/
TiX1000
TI-LENS/TELE2
2x Telephoto infrared smart lens • • • •
TI-LENS/WIDE2
Wide Angle Infrared Smart Lens† • • • •
FLK-Lens/4xTele2
4x Telephoto infrared smart lens • • • •
FLK-Lens/FLK-Lens/25Mac2
25 Micron macro infrared smart lens† • • • •
FLK-XLens/SupWide
Super wide-angle lens • • •
FLK-XLens/Wide
Wide-angle lens • • •
FLK-XLens/Stan
Standard lens • • •
FLK-XLens/Tele
Telephoto lens • • •
FLK-XLens/SupTele
Super telephoto lens • • •
FLK-Xlens/Macro1
Close-up 0.2x • • •
FLK-Xlens/Macro2
Close-up 0.5x; 34.3 x 25.3mm2; 32 um; • • •
FLK-Xlens/Macro3
Close-up 0.5x • • •
Infrared lens compatibility
Get the best image possible with optional standard, telephoto and wide angle lenses. Bring small and distant objects
closer with a telephoto lens, or widen your field of view in tight spaces with a wide angle lens.
The lenses for TiX580, TiX560, TiX520, TiX500, Ti480, Ti450, Ti400, Ti300, and Ti200 are smart lenses. They
come pre-calibrated and don't require calibration to a specific camera, so they are interchangeable between
compatible cameras. Lenses for TiX1000, TiX660, and TiX640 require calibration to the specific camera.
For more information, go to www.fluke.com/accessories
39
Infrared cameras
Model number
Ti27/
TiR27 /
Ti29/
TiR29/
Ti32/
TiR32
Ti29/
TiR29
Ti32/
TiR32
Ti90/
Ti95
TiS10/
TiS20/
TiS40/
TiS40
TiS55/
TiS60/
TiS65/
TiS75
Ti100/
Ti105/
T i110/
TiR105/
T i R110
TI125/
TiR125
Ti200/
Ti300/
Ti400
Ti450/
Ti480
TiX500/
TiX520/
TiX560/
TiX580
TiX620/
TiX640/
TiX660/
TiX1000
TI-SBC3B
Battery Charging Base • • • • • • • • •
TI-SBP3
Rechargeable Lithium Ion Smart
Battery Pack • • • • • • • •
TI-SBP4
Rechargeable Lithium Ion Smart
Battery Pack
TI-CAR CHARGER • • • • • • • • •
FLK-XBattery
FLK-XCharger
FLK-TI-BLUETOOTH • •
FLK-XPower Plug
FLK-XEthernet 5m
FLK-XHDMI Cable
Model number
Ti10/
Ti25/TiR/
TiR1/Ti20
Ti27/
TiR27
Ti29/
TiR29
Ti32/
TiR32 Ti90/Ti95
Ti100/
Ti105/
T i110/
TiR105/
T i R110
Ti125/
TiR125
Ti200/
Ti300/
Ti400/
Ti450/
Ti480
TI-VISOR ••••
TI-VISOR2 •••
TI-VISOR3
Model number Ti90/Ti95
TiS10/TiS20/
TiS40/TiS40
TiS55/TiS60/
TiS65/TiS75
Ti100/Ti105/
Ti110/TiR105/
T i R110 Ti125/ TiR125
Ti200/Ti300/
Ti400/Ti450/
Ti480
TI-TRIPOD2 • •
TI-TRIPOD3 • •
Battery and charger compatibility
Sun visor compatibility
Tripod base compatibility
Prevent the unexpected loss of power with our rugged and rechargeable battery packs and keep
your Fluke infrared camera charged while youre on the road with our car charger.
Instantly reduce LCD screen glare and reflections in bright sunlight or other areas where ambient
lighting conditions are bright with our durable, heavy-duty plastic visor. It can be used inside or
outside, and easily clips onto to your Fluke infrared camera without the need for any additional
hardware.
Lightweight, one-piece mounting accessory quickly and easily attaches to your Fluke Infrared
Camera and allows you to mount to a standard tripod or monopod for those applications or situa-
tions that require a more stable or semi-fixed platform.
40
Portable oscilloscopes
Model number 120 Series 190 Series 190 Series II
Safety designed scopemeter voltage probes
VPS420-X
Safety designed oscilloscope probe accessories
AS400
RS400 • •
RS500 • •
AC current clamps
i5s •••
Automotive
SCC128
SCC198
SCC298
Industrial test lead accessories
TP920 •••
AC120 •••
Safety designed cables and adapters
PM9091 • •
PM9092 • •
PM9093 • •
PM9081 2-channel
PM9082 • •
BB120
TRM50 • •
Miscellanous
BHT190 125 only
HH290
CS20MA 2-channel
MA190 • •
EBC290
Compatibility chart VPS420-X High Working
Voltage Ruggedized Probe
Set include: VPS420-X 100:1,
150 MHz
X = Red, Blue, Grey or Green (V)
Hook clip for probe tip (Black)
Large jaw probe clip (Black)
Reference lead with 4 mm
Banana plug (Black)
Large jaw alligator clip for 4 mm
banana plug (Black)
AS400 Probe Accessory
Extension Set
For VPS400-Series Probes
CAT III 1000 V/CAT IV 600 V
Reference lead with 4 mm plug
(Black), overall length 60 cm
Reference lead with hook clip
(Black), overall length 22 cm
Large jaw probe clip (black)
CAT II 1000 V
2 mm test probe for probe tip
(1x, black)
4 mm test probe for probe tip
(1x, black)
RS400 Probe Accessories
Replacement Set
For VPS400-Series Probes and
VPS210-Series Probes
CAT III 1000 V/CAT IV 600 V
1x Probe hook clip (black)
Ground lead with mini alligator
clip
2x Insulation sleeve (black)
CAT II 30V
2x Ground spring (black)
RS500 Probe Accessories
Replacement Set
For VPS510 Series Probes
CAT II 300 V
1x hook clip (black)
1x ground lead with mini
alligator clip (black)
2x insulation sleeves for probe’s
ground contact (black)
1x BNC to probe tip adapter
(black)
CAT II 30 V
2x ground browsers (black)
1x insulated mini screwdriver,
for probe adjustment purposes
i5s AC Current Clamp
0.01 A to 5 A
Range 400 mV/A
Basic accuracy % reading: 1 %
Usable frequency range:
40 Hz to 5 kHz
TP920 Test Probe
Adapter Kit
Suited for STL120 Test Leads (Not
compatible with STL120-III), TL71
Test Leads, TL75 Test Leads and
TL76 Test Leads
The set consists of:
IC test tip adapters for probing
closely spaced test points, such
as the pins of integrated cir-
cuits, without shorting adjacent
leads. Maximum current han-
dling 3A
Extended probe tips allow test-
ing of hard to reach points.
Maximum current handling 3A
Medium size alligator clips have
maximum jaw opening of 7.6
mm (0.30 in)
Rated for 3 A max
TAS 90 Shielded Test lead
Accessory Set
Set 4 mm adapters for Banana
plug (1x red, 1x grey, 2x black)
Set of back probe pins for
Banana plug (1x red, 1x grey, 2x
black)
CAT II 30 V
Rated for 1A max
PM9091 Set of 3x Coaxial
Cables with BNC connec-
tors
Length: 1.5m each
Impedance: 50 ohm
Color: 1xRed, 1xBlack, 1x3x
Grey
Max signal voltage: 300 V rms
Max voltage to ground:
600 V rms CAT III per IEC/
EN61010-031
PM9092 Set of Coaxial
cables with BNC connec-
tors
Length: 0.5 m each
Impedance: 50 ohm
Color: 1x red, 1x black, 1x grey
Max signal voltage: 300 V rms
Max voltage to ground:
600 V rms CAT III per IEC/
EN61010-031
PM9093 Adapter BNC
(male) to Dual BNC (female)
in T model (6)
Color: 2x black
Max signal voltage: 300 V rms
CAT III per IEC/EN61010
Max voltage to ground: 600V
rms CAT III per IEC/EN61010
PM9081 Adapter BNC
(female) to Dual Banana
Jack
Color: 2x red, 2x black
Max signal voltage: 600Vrms
CAT III per IEC/EN61010
Max voltage to ground: CAT III
600 Vrms / CAT II 1000 V per
IEC/EN61010
PM9082 Adapter BNC
(male) to Dual Banana Jack
Color: 2x red, 2x black
Max signal voltage: CAT III
600 Vrms per IEC/EN61010
Max voltage to ground: CAT III
600Vrms /CAT II 1000V per
IEC/EN61010
BB120 Adapter BNC
(female) to Shielded
Banana Jack
Set of 2
Max signal voltage: 300 Vrms
CAT III per IEC/EN61010
Max voltage to ground: 600 V
CAT III per IEC/EN61010
TRM50 Coaxial Feed-
through BNC male to BNC
female Cable Terminator
Set of 2
Specification
Impedance: 50 ohm
Max voltage over ground:
CAT III 1000 V
Max power 1W
BHT190 Bus Health Test
Break-out Adapter Set
Board with M12 connectors
(male to female, 5 pins)
DB-9 connectors (male to
female, 9 pins + shield)
RJ-45 connector, with short
patch cable providing male to
female interconnection (8 pins)
CS20MA Current Shunt for
AC and DC measurements
on 4 to 20mA control loops
Sensitivity: 10mV/mA
Shunt resistance: 10 ohm
Bandwidth: > 10 kHz
Max voltage to ground: CAT III
30 Vrms per EN/IEC 61010
MA190 Medical Applica-
tions Accessory Kit
1x 50 ohm BNC feed through
terminator
1x 50 ohm BNC feed through
terminator with 10:1 signal
attenuator
1x 1 ohm current shunt in BNC
feed through
1x BNC terminated coax cable
1x Single piece insulated BNC
(female) to 4mm Banana plug
adapter
2x Pieces dual 4mm Banana
receptacles (1x red, 1x black)
EBC290 External Charger
For Fluke 190 Series II
ScopeMeter® Oscilloscope
Charging time (BP291): five
hours, giving an operating time
of up to seven hours
DC input voltage: 15 V to 23V,
714 mA nom. (dc input from
BC190: 17.8 V / 0.84 A max)
For more information, go to www.fluke.com/accessories
41
Portable oscilloscopes
Caution!
DO NOT use these probes to measure high
voltages on power distribution systems. The
probes provide high accuracy when used
with a multimeter having 10 megohm input
impedance.
42
High voltage
80K-40 High Voltage
Probe
Extends the voltage measuring
capability of an ac/dc multimeter
to 40,000 V peak ac or dc. This
probe is designed for taking
measurements on low-energy
circuits within equipment only,
such as televisions or photo copy
machines.
Voltage range: 1 kV to
40,000kV, dc or peak ac,
28 kV rms ac
Accuracy: 20 kV to 35 kV;
± 1 % at 20 °C to 30 °C
Division ratio: 1000:1
Meets IEC 61010-031 Type B,
40 kV dc or peak ac, 28 kV rms
ac, (voltage derived from
limited energy transformer)
80K-6 High Voltage Probe
Extends the voltage measuring
capability of an ac/dc digital mul-
timeter to 6,000V peak ac or dc.
This probe is designed for taking
measurements on low-energy
circuits within equipment only.
Voltage range: 0 kV to
6kV, dc or peak ac
Accuracy: dc to 500 Hz ± 1 %;
500 Hz to 1 kHz ± 2 %; above
1 kHz output falls, -30 % at
10kHz
Division ratio: 1000:1
Meets IEC 61010-031 Type B,
40 kV dc or peak ac, 28 kV rms
ac, (voltage derived from
limited energy transformer)
80K-15 High Voltage Probe
Extends the voltage measuring
capability of an ac/dc digital
multimeter to 15,000 V peak ac
or dc. This probe is designed for
taking measurements on low-
energy circuits within equipment
only.
Voltage range: 1 kV to 15 kV dc
or peak ac, 10 kV ac rms
Accuracy: dc ± 2 % 60 Hz;
± 5 %
Division ratio: 1000:1
Meets IEC 61010-031 Type B,
40 kV dc or peak ac, 28 kV rms
ac, (voltage derived from
limited energy transformer)
High frequency
85RF High
Frequency Probe
Converts a dc voltmeter with an
input impedance of 10 megohms
into a high frequency (100 kHz
to 500 MHz) RF voltmeter. The
probes dc output is calibrated to
be equivalent to the rms value of
a sine wave input.
Voltage range: 0.25 V to
3 V ac rms
Maximum input: 30 V rms,
200 V dc
AC to dc ratio: 1:1
Ratio accuracy at 25 MHz and
loaded with 10 megohms
–Above 0.5 V: ± 0.5 dB
–Below 0.5 V: ± 1.0 dB
Add ± 0.2 dB in RF fields of
1V/m to 3 V/m
Frequency response relative to
25 MHz:
100 KHz to 100 MHz
± 0.5 dB
100 MHz to 200 MHz
± 2.0 dB
200 MHz to 500 MHz
± 3.0 dB
Specialty probes
80K-40 80K-15
80K-6
80K-15, 85RF
85RF
*Obsolete
**OC4 USB REV II Cable
Application Hardware Operating System Software
FVF-Basic
Pentium class or better microprocessor
Windows XP, 7, 8, 10
32 MB RAM
70 MB disk space (100 MB to install)
FVF-Full
Pentium class or better microprocessor
Windows XP, 7, 8, 10
32 MB RAM
70 MB disk space (100 MB to install)
FVF-Upgrade
Pentium class or better microprocessor
Windows XP, 7, 8, 10
32 MB RAM
70 MB disk space (100 MB to install)
Hardware and software requirements
43
For more information, go to www.fluke.com/accessories
FlukeView® Forms Basic
This application transfers data
from a Fluke test tool to a PC,
using two standard, non-
customizable forms to display
measurement readings in table
or graphical form. This software
includes a cable appropriate for
your measuring instrument.
FlukeView® Forms Full
This application provides the
FlukeView Forms Basic software
functions in addition to custom-
izable documents and custom
templates using the FlukeView
Forms Designer. This software
includes a cable appropriate for
your measuring instrument.
FVF-UG FlukeView®
Forms Upgrade
This upgrade is designed for
users of FlukeView Forms Basic
who want to include the features
of FlukeView Forms Full. It can
also be used by FlukeView Forms
Full users who want to use the
latest version of the software.
No cable is provided with this
option. This upgrade is compat-
ible with all previous versions of
FlukeView Forms.
Software
FVF BASIC
FVF option
Interface cable
Fluke instrument compatibility
FVF-Basic
USB** / IR
280 Series Digital Multimeters
789 ProcessMeter
1550C MegOhmMeter
1664 FC Installation Tester
180 Series* Digital Multimeter
FVF-SC5
USB** / Serial
8808A Digital Multimeter
8845A 6.5 Digit Precision
Multimeters
8846A 6.5 Digit Precision
Multimeters
45* Dual Display Multimeter
FVF FULL
FVF option
Interface cable
Fluke instrument compatibility
FVF-SC1
Serial / IrDA
53-II Single Input Digital
Thermometer with data logging
89-IV* Digital Multimeter
54-II Dual Input Digital
Thermometer
FVF-SC2
USB** / IR
568 Infrared and Contact
Thermometer
789 ProcessMeter
280 Series Digital Multimeter
1550C/1555 MegOhmMeter
1664 FC Installation Tester
180 Series* Digital Multimeter
FVF-SC4
USB** / Serial
8808A Digital Multimeter
8845A 6.5 Digit Precision
Multimeters
8846A 6.5 Digit Precision
Multimeters
45* Dual Display Multimeter
975 AirMeter
FVF-UPGRADE
FVF option
Interface cable
Fluke instrument compatibility
FVF-UG
No cable included
Any instrument that supports FlukeView Forms software
FlukeView® Forms compatibility chart
FlukeView® Forms
Fluke offers a popular
line of test accessories
specifically designed for
automotive systems and
components, both electric
and electronic. These
accessories are compatible
with all Fluke meters.
BP880 BNC to Female
Double Stacking Banana
Converts a BNC scope lead to a