1B31 Datasheet by Chemtronics

View All Related Products | Download PDF Datasheet
CHASE Electronic Coatings C We make I Inlferlal difference
04413 Page 1 of 2
HumiSeal® 1B31 Acrylic Conformal Coating
Technical Data Sheet
HumiSeal® 1B31 is a fast drying, single component, acrylic conformal coating that provides excellent moisture and
environmental protection for printed circuit assemblies. HumiSeal® 1B31 demonstrates excellent flexibility,
fluoresces under UV light for ease of inspection and is easily repaired. HumiSeal® 1B31 coating is MIL-I-46058C
qualified, IPC-CC-830 and RoHS Directive 2002/95/EC compliant.
Properties of HumiSeal® 1B31
Density, per ASTM D1475 0.91 ± 0.02 g/cm³
Solids Content, % by weight per Fed-Std-141, Meth. 4044 35 ± 3 %
Viscosity, per Fed-Std-141, Meth. 4287 200 ± 15 centipoise
VOC 592 grams/litre
Drying Time to Handle, per Fed-Std-141, Meth. 4061 10 minutes
Recommended Coating Thickness 25 - 75 microns
Recommended Curing Conditions 24 hrs @ RT or 30 min @ 76°C
Time Required to Reach Optimum Properties 7 days
Recommended Thinner (dipping & brushing) HumiSeal® Thinner 503
Recommended Thinner (spraying) HumiSeal® Thinner 521, 521EU
Recommended Stripper HumiSeal® Stripper 1080, 1080EU
Shelf Life at Room Temperature, DOM 24 months
Thermal Shock, 50 cycles per MIL-I-46058C -65°C to 125°C
Coefficient of Thermal Expansion - TMA 170 ppm/°C below Tg
340 ppm/°C above Tg
Glass Transition Temperature - DSC 14°C
Modulus - DMA 2000 MPa @ -40°C
1050 MPa @ 20°C
8.5 MPa @ 60°C
Flammability, per MIL-I-46058C Self-Extinguishing
Dielectric Withstand Voltage, per MIL-I-46058C >1500 volts
Dielectric Breakdown Voltage, per ASTM D149 7500 volts
Dielectric Constant, at 1MHz and 25°C per ASTM D150-98 2.5
Dissipation Factor, at 1MHz and 25°C per ASTM D150-98 0.01
Insulation Resistance, per MIL-I-46058C 8.0 x 1014 ohms (800T)
Moisture Insulation Resistance, per MIL-I-46058C 6.0 x 1010 ohms (60G)
Fungus Resistance, per ASTM G21 Passes
Application of HumiSeal® 1B31
Cleanliness of the substrate is of extreme importance for the successful application of a conformal coating.
Surfaces must be free of moisture, dirt, wax, grease, flux residues and all other contaminants. Contamination
under the coating could cause problems that may lead to assembly failures.
Depending on the complexity, density and configuration of components on the assembly, it may be necessary to
reduce the viscosity of HumiSeal® 1B31 with HumiSeal® Thinner 503 in order to obtain a uniform film. Once
optimum viscosity is determined, a controlled rate of immersion and withdrawal (5-15 cm/min) will further ensure
even deposition of the coating and ultimately a uniform film. During the application, evaporation of solvent
causes an increase in viscosity that should be adjusted by adding small amounts of HumiSeal® Thinner 503.
Viscosity in the dip tank should be checked regularly using a simple measuring device such as a Zahn or Ford
viscosity cup.
CHASE ElecIrumc Coatings We make a material diflerence sales@humxsea\mm eurogeansalechhasecam mm humlsealsarl chaseoor com euroDelechsuDDorl®chaseoorD mm asxalechsuDDortfihumsealLom techsuggothuwseaLcUm
04413 Page 2 of 2
HumiSeal® 1B31 Technical Data Sheet
HumiSeal® 1B31 can be sprayed using conventional spraying equipment. Spraying should be done in an
environment with adequate ventilation so that the vapour and mist are carried away from the operator. The addition
of HumiSeal® Thinner 521 or 521EU is necessary to ensure a uniform spray pattern resulting in pinhole-free film.
The amount of thinner and spray pressure will depend on the specific type of spray equipment used and operator
technique. The recommended ratio of HumiSeal® 1B31 to HumiSeal® Thinner 521 or 521EU is 1:1 by volume;
however the ratio may need to be adjusted to obtain a uniform coating.
HumiSeal® 1B31 may be brushed with a small addition of HumiSeal® Thinner 503. Uniformity of the film depends
on component density and operator's technique.
HumiSeal® 1B31 should be stored away from excessive heat or cold, in tightly closed containers. HumiSeal®
products may be stored at temperatures of 0 to 35°C. Prior to use, allow the product to equilibrate for 24 hours at a
room temperature of 18 to 32°C.
Application of HumiSeal® Conformal Coatings should be carried out in accordance with local and National Health
and Safety regulations.
The solvents in HumiSeal® Conformal Coatings are flammable. Material should not be used in presence of open
flame or sparks. Use only in well-ventilated areas to avoid inhalation of vapours or spray. Avoid contact with skin
and eyes.
Consult MSDS/SDS prior to use.
Contact HumiSeal®
HumiSeal North America
201 Zeta Drive
Pittsburgh, PA 15238
Tel: +1 412-828-1500
Toll Free (US only): 866-828-5470
HumiSeal Technical Center
295 University Avenue
Westwood, MA 02090
Tel: +1 781-332-0734
Fax: +1 781-332-0703
HumiSeal Europe
505 Eskdale Road, IQ Winnersh
Berkshire RG41 5TU
Tel: +44 (0)1189 442 333
Fax: +44 (0)1189 335 799
HumiSeal Europe Support
Tel: +44 (0)1189 442 333
Fax: +44 (0)1189 335 799
HumiSeal S.A.R.L
4/6 Avenue Eiffel
78420 Carrieres-Sur-Seine
Tel: +33 (0) 1 30 09 86 86
Fax: +33 (0) 1 30 09 86 87
HumiSeal Asian Support
Tel: 852-9451-6434
Fax: 852-2413-6289
The information contained here is provided for product selection purposes only and is not to be considered specification or performance data. Under no circumstance will the
seller be liable for any loss, damage, expense or incidental or consequential damage of any kind arising in connection with the use or inability to use its product. Specific
conditions of sale and Chase's limited warranty are set out in detail in Chase Corporation Terms and Conditions of Sale. Those Terms and Conditions are the only source that
contain Chase's limited warranty and other terms and conditions.