15DYS865-120500W Datasheet

\-/}//}//}//}//}//}//}/II}//}//}//}II}//}//}//}//}III}III\I LEE III}//}ll}ll}ll}ll}II}Ill}II}II}//}//}//}II}II}II}III}III www.idealpower.co.uk
1
SPECIFICATION FOR APPROVAL
CUSTOMER/客户 : 01097
ARTICLE/品名: SWITCHING MODE POWER SUPPLY
SPECIFICATION /规格: Desktop/桌上式
MODEL NO/产品型号. : DYS865-120500W
OUR PART NO./产品编号: DYS865-120500-19C28F
CUSTOMER P. N/客户料号:
INPUT/输入 : 100-240V AC 50/60Hz
OUTPUT/输出: 12.0V DC 5.0A
INPUT/输入 : 100-240V AC 50/60Hz
REV/DATE:/版本/日期： 02 2020/01/04
Vendor Confirmation/供应商确认
Confirmation Approved/客户确认
Made by
Checked by
Approved by
Made by
Checked by
Approved by
Liuhuixian
Liufei
Wuguoming
Remark/备注：
IDEAL POWER LTD
14 Larks Way, Tree Beech Enterprise Park Gunn, Barnstaple, Devon, EX32 7NZ,
England
Tel. +44 (0)845 260 3400 Web. www.idealpower.co.uk
G IDEALPOWER experts m power cowverswon
SWITCHING MODE POWER SUPPLY
SPECIFICATION
2
E.C.LIST/变更履历表
Description of Change/变更内容描述
Changed
Date/日期
Operator/
执行者
Before/变更前
After/变更后
Original Release(初次发行)
2019/12/30
Liuhuixian
Update DC Cord Drawing
2020/01/04
Liuhuixian
G IDEALPOWER experts m power converswou
SWITCHING MODE POWER SUPPLY
SPECIFICATION
3
CONTENTS/目录
1 Compendium/简述 …………………………………………………………………………….…. ….…. ……….…..….....4
2 Input Characteristics/输入特性 ………………………….………………………….. ….…. ……….….………….…..….4
2.1 Input Voltage & Frequency/输入电压&频率 ……..………………………………….…. ……….….……….…..….4
2.2 Input AC Current/AC 输入电流 …..……………………………………………..…….…. ……….….……….…..….4
2.3 Inrush Current (Cold Start)/浪涌电流(冷启动) …….………………….…………….…. ……….….……….…......4
2.4 Efficiency (Normal)/效率(额定输入) …………………………………..…….………. ……….….……….…..…….4
2.5 Energy Consumption /空载功耗………………………………………………….. ….…. ……….……….…..……..4
3 Output Characteristics/输出特性 …………………………………………………...…………….…. ……….….….….....5
3.1 Static Output Characteristics <Vo & R+N>/静态输出特性 ………..……...….…….…. ……….….…….…..…....5
3.2 Line / Load Regulation/线性/负载调整率 …...………….……………..……………….…. …….….…….….. .….5
3.3 Turn on Delay Time/开机延迟时间 …………………………………….…………. ………….….….….…….…..…5
3.4 Hold up Time/关机维持时间 …………………………………………………..……….…. ……….….…….…..…...5
3.5 Capacitance Load/容性负载………………………………………………………..……….…. …….….…….……..5
3.6 Output Overshoot / Undershoot/输出过冲/欠冲 ……………………………………….….…….…..….….…….....5
3.7 Output Load Transient Response/输出负载瞬态响应 …..…………….……………….….…….…..……….…….6
4 Protection Requirements/保护特性 ……………………………………………..…………….….…….…..………….......6
4.1 Over Current Protection/过流保护 ………………………………………………………….….…….…..……..…....6
4.2 Short Circuit Protection/短路保护 ………………………………...………………………….….…….…..…..........6
4.3 Over Voltage Protection/过压保护…………………………………………………………….….…….…...………..6
5 Environment Requirements/环境要求 .…….……….…….……………………….….. …………….….…….…..………6
5.1 Operating Temperature and Relative Humidity/操作温/湿度要求 …………...…. ………….….…….…..……....6
5.2 Storage Temperature and Relative Humidity/存储温/湿度要求 ……..……...…………….….…….…..……..…..6
5.3 Vibration/振动 ……………………………………………..……………….………………….….…….…..……….....6
5.4 Drop in /跌落 …………………………………………………………………………….….…….…..………………..6
6 Reliability Requirements/可靠性要求………………………………………………………………………………………7
6.1 Burn-in/煲机………………………………………………………………………….….…….…...….. ………………7
6.2 MTBF Qualification/平均间隔故障时间估算………………………………...……………………………….............7
7 EMI/EMS Standards/EMI/EMS 标准………………………………………………………………………………………….7
7.1 EMI Standards/EMI 标准…………….………………………………….….…….…...…….......................................7
7.2 EMS Standards/EMS 标准……………………………………………………………………………….….…….…….7
8 Safety Standards/安规标准………………………………….…..……………………………………….….………….…….8
8.1 Safety Accord with/安全:符合标准………………………………..……………………………………………………...8
8.2 Dielectric Strength(Hi-pot)/介电耐压强度(高压) ………………...………………………………………………...…..8
8.3 Leakage Current/漏电流…………………………………………...……………………….........................................8
8.4 Insulation Resistance/绝缘阻抗…………………………………...………………………….....................................8
9 Outline Drawing/外观示意图: ……………………………….......……………………………..........................................9
10 DC Cord Drawing/DC 线示意图: ……………………………..…………………………………….………………….....10
11 Marking Drawing/铭牌示意图: ……………………………………………………………...............................................11
12 Package Drawing/包装示意图: ……………………………………………………………..............................................12
G experts m power cowverswou DID EDD
SWITCHING MODE POWER SUPPLY
SPECIFICATION
4
1.Compendium/简述
The document details the electrical, mechanical and environmental specifications of a SMPS,
the power supply provides 60W continuous output power.
资料详细描述了一款 60W(连续输出功率)开关电源的电气性，结构性及环境等要求.
The power supply shall meet the RoHS requirements.
此款电源符合 RoHS 要求.
1.1 Description/描述
SMPS Adapter(Wall mount)/插墙式适配器 SMPS Adapter(Interchangeable)/可换头适配器
SMPS Adapter(Desk-top)/桌面型适配器 Open Frame/开放式结构
SMPS Unit (With Case)/带铁壳型 Others/其他
2. Input Characteristics/输入特性
2.1 Input Voltage & Frequency/输入电压与频率
The range of input voltage is from 90Vac to 264Vac with a single phase.
输入电压范围：从 90Vac 到264Vac, 单相输入.
Minimum/最小
Nominal/额定值
Maximum/最大
Input Voltage/输入电压
90Vac
100Vac~240Vac
264Vac
Input Frequency/输入频率
47Hz
60Hz/50Hz
63Hz
2.2 Input AC Current/AC 输入电流
1.5Amax @ 100-240Vac input & Full load/在100 – 240 Vac 输入和满载条件下最大 1.5A有效值
2.3 Inrush Current (cold start)/浪涌电流(冷启动)
The inrush current will not exceed 80A at 100-240Vac input and Max load for a cold start at
25℃
在100-240V 交流电输入和最大负载冷启动环境 25℃时浪通电流不能超过 80A
2.4 Average Efficiency/平均效率
While input 115Vac and 230Vac, the average efficiency is more than 88.0%.
The test point is at 25%, 50%, 75% and 100% of max load respectively.
在输入 115Vac 和 230Vac 条件下，平均效率不小于 88.0%。
测试点分别是最大载的 25%,50%,75%和100%。
2.5 Energy Consumption /空载功耗
G IDEALPOWER experts m power cowverswon H»
SWITCHING MODE POWER SUPPLY
SPECIFICATION
5
While input 115Vac or 230Vac and the output is no load,the input power loss must be
less than 0.21W
在输入 115Vac/230Vac 时,空载功耗小于 0.21W
3. Output Characteristics/输出特性
3.1 Static Output Characteristics <Vo & R+N>/静态输出特性<输出&纹波+噪音>
Output
Rated Load/额定负载
Output Range
输出电压范围
R+N
纹波与噪声
Remark
备 注
Rate
Min. Load
Max. Load
+12V
0.0A
5.0A
11.4V-12.6V
150mVp-p
Ripple & Noise: Measurement is done by 20MHz bandwidth oscilloscope and the outputparalleled
a 0.1uF ceramic capacitor and a 10uF electrolysis capacitor.
(test under the condition of rated input and rated output)
纹波与噪声: 量测时示波器选用 20MHz 带宽限制,输出端要并联一颗 0.1uF 的陶瓷电容和一颗 10uF
的电 解电容. (在额定输入及输出的条件下检测)
3.2 Line/ Load Regulation/线性/负载调整率
3.3 Turn - on Delay Time/开机延迟时间
3S max. @ 100 Vac to 240 Vac input & Full load
在100Vac 到240Vac 输入和满载条件下最大 3S
3.4 Hold-up Time/关机维持时间
5mS min. @ Full load &115Vac/60Hz input turn off at worst case
在 115Vac 输入,满载同时最差情况下关机，最小 5mS
3.5 Capacitance Load/容性负载
While input 100~240Vac and capacitance load is 470uF, the adapter can turn on normally
and the output is in the rated range.
在输入 100~240Vac，470uF 容性负载条件下，适配器能正常开机。
并且输出电压范围在额定范围下。
3.6 Output Overshoot / Undershoot/输出过冲/欠冲
10% max. When the power on or off
Output
Load Condition/负载条件
Line Regulation
线性调整率
Load Regulation
负载调整率
Remark
备 注
Rate
Min. Load
Max. Load
+12V
0.0A
5.0A
备注：黑色 不带灯孔
DYS602DYS602桌面式 PC
2013.03.14
外型图
1
A4 mm
6
5
4
3
2A
A
B
C
D
EE
D
C
B
A
12 3 456
Dongguan Dongsong
Electronic Co., Ltd. 吕冬萍 高 峰
宾 成
材料
型号
批准
设计 校对
设计日期
单位 版本
尺寸公差
产品名称
图号
图寸
3%
5%
G IDEALPOWER experts m power converswou
SWITCHING MODE POWER SUPPLY
SPECIFICATION
6
当电源开/关机时,10%最大
3.7 Output Load Transient Response/输出负载瞬态响应
the output shall not exceed 10% of the nominal output voltage, load flunctuation: from 20% to
80%, R/S: 0.5A/uS, frequency: 100Hz duration and 8mS at 80%.
输出电压不能超过额定电压的 10%,负载变化: 从20%到80%, 斜率: 0.5A/uS, 频率: 100Hz,
80%负载持续时间为 8mS.
4. Protection Requirements/保护要求
4.1 Over Current Protection/过流保护
Over Current Point Limited/过流点限制：I ＞ 6.5A
The output shall hiccup when the over currents applied to the output rail, and shall be
self-recovery when the fault condition is removed
当过电流时，输出将进入打嗝模式，当过流情况解除后，产品将会自动恢复正常
4.2 Short Circuit Protection/短路保护
The input power shall decrease when the output rail short, the power supply shall no
damage, and shall be self-recovery when the fault condition is removed
当输出短路时,产品输入功率降低且不会损伤,当短路情况解除后,产品将会自动恢复正常
4.3 Over Voltage Protection/过压保护
The power supply shall protection when the output over voltage。
当输出发生过压时，产品进入保护模式.
5. Environment Requirements/环境要求
5.1 Operating Temperature and Relative Humidity/操作温/湿度要求
0°C to +40°C
10%RH to 90%RH
5.2 Storage Temperature and Relative Humidity/存储温/湿度要求
-20°C to +80°C
5%RH to 95%RH non-condensing @ Sea level shall be low 10,000 feet/低于 10,000 英尺
5.3 Vibration/振动
10 to 300Hz sweep at a constant acceleration of 1.0G(Breadth: 3.5mm) for 1Hour for
each of the perpendicular axes X, Y, Z
扫描频率: 10 to 300Hz, 加速度: 1.0G(位移: 3.5mm), X, Y, Z 三垂直坐标轴向各振动 1 小时
G IDEALPOWER experts m power cowverswon E DDDDDXX H» H- DDfiD D DEEDS D
SWITCHING MODE POWER SUPPLY
SPECIFICATION
7
6.Reliability Requirements/可靠性要求
6.1 Burn-in/煲机
The power supply shall be burn-in at least 4 Hours under normal input and
80% rated load at 40℃
5℃
产品至少要在 40℃
5℃的环境及 80%以上额定负载条件下煲机 4小时
6.2 MTBF Qualification/平均间隔故障时间估算
The MTBF shall be at least 50,000hours at 25°C, Full load and nominal
input condition
平均间隔故障时间: 至少 50,000 小时,25°C 环境及额定输入与满载条件下
7. EMI/EMS Standards/EMI/EMS 标准
7.1 EMI Standards/EMI 标准
FCC Part15 class B
EN55032 EN55014-1 EN61204-3(CISPR 22)
AS/NZS CISPR22 AS/NZS CISPR13 AS/NZS CISPR14.1
GB9254 GB13837 GB17625.1
J55032 J55013 J55014-1
KN22 KN13 KN14-1
CNS13438
7.2 EMS Standards/EMS 标准
EN55035 EN55020 EN55014-2 EN61204-3
7.2.1 IEC 61000-4-2, electrostatic discharge(ESD) requirement/静电抗扰度要求
Discharge characteristic/静电规格
Test level/测试条件
Test criteria/测试标准
Air discharge/空气放电
+/-8KV
B
Contact discharge/接触放电
+/-4 KV
B
7.2.2 IEC 61000-4-4, electric fast transients(EFT) immunity requirement/电快速瞬变脉冲群
Coupling/测试端口
Test level/测试条件
Test criteria/测试标准
AC-input/交流输入
0.5KV
A
AC-input/交流输入
1KV
B
7.2.3 IEC 61000-4-5, surge capability requirement/浪涌抗扰度要求
Surge voltage/雷击电压
Test criteria/测试标准
G IDEALPOWER experts m power cowverswon DDDDDDDDD DDDXfiXE D EDD
SWITCHING MODE POWER SUPPLY
SPECIFICATION
8
Differential mode/差模 +/-1KV
A
Common mode/共模 +/-2KV
7.2.4 Assessment criteria /评估标准
8. Safety Standards/安规标准
8.1 Safety Accord with/安全:符合标准
UL60950-1,CSA C22.2 NO.60950-1 UL62368-1,CSA C22.2 NO. 62368-1
UL1310
IEC60950-1 IEC62368-1 IEC61558-1,IEC61558-2-16
EN60950-1 EN62368-1 EN61558-1,EN61558-2-16
AS/NZS 60950.1 AS/NZS 62368.1 AS/NZS 61558.1,AS/NZS 61558.2.16
GB4943.1 GB8898
J60950-1 J62368-1 J61558-1,J61558-2-16
K60950-1 K60065
CNS14336-1 CNS14408
Note: AC pins corresponding to relative national standards.
注：相应的 AC 插脚对应相应国家的标准.
8.2 Dielectric Strength(Hi-pot)/介电耐压强度(高压)
Primary to Secondary: 4242VDC / 5mAMax / 60second(3 seconds for mass
production)
初级对次级: 4242VDC / 5mAMax / 60 秒(生产时高压测试时间: 3秒)
8.3 Leakage Current/漏电流
0.25mAmax. at 264Vac / 50Hz / 在264Vac / 50Hz 输入时，最大漏电流 0.25mA
Acceptable criteria
可接受标准
Performance
性能
A
Performance is not allowed to be changed, any changes should be
within the specified limits
性能不允许变化；如果性能会发生变化，则变化的范围在产品规格书规
定的范围内.
B
During the testing process, the performance degradation is allowed
within the specifications of the product specification. After the
elimination, the equipment can return to normal and no reset or any
manual intervention is allowed. .
设备在测试过程中,性能降低允许在产品规格书要求范围内,干扰消除
后,设备能恢复正常,不允许出现复位和任何方式的人工干预.
G IDEALPOWER experts m power conversion +09% IE!- IE nu a w. n [I]. In nu w I I: I I9 lululntfi n rum [lull—fl u: an I u L—qflmll g—- .1“ mail): n ms nu-
SWITCHING MODE POWER SUPPLY
SPECIFICATION
9
8.4 Insulation Resistance/绝缘阻抗
50MΩ min. at primary to secondary add 500Vdc test voltage
在初级与次级间加 500Vdc 进行测试,最小绝缘阻抗 50MΩ
9. Outline Drawing/外观示意图:
expsns m power conversion G IDEALPOWER aiming: 1200310 nuns: m ms mm mm: Mm. mm mm: sax sunnncuxwimumnnm, “an; zununmmumma ”’5’!“ unw- mr NASH/”mm“ mama: nmnm » Imo mm as: mz.n:na ,— DYS DC009 ms ‘— I I“ m LJ—u II mltfllfl I — e—e—e MM m 3"“: mama Ea LDC PLUGMZJ‘OSS'IZO axxm-ms)‘ SZCHDN A-A 2.5R SIZE26‘8‘65‘2‘4 ii a— Re“ Jnkflimslllll u u an n ‘ m a . m . “‘- 9 man a
SWITCHING MODE POWER SUPPLY
SPECIFICATION
10
10. DC Cord Drawing/DC 线示意图:
IDEALPOWER expensxn powerconvermon G 122 HRH“ it ‘F ULOGOFAZIE'L' L1 '1' 31'- EE m if: 74 HI flfitfiwm 2 "7 V m I v ‘ omawegiflfjm’” 5"“ @_ must}; mm u Izw . m m. 9+. C£@.@&éfi r63 ..m.mm mm“... m. 7 "a! n-mumumy u 1... Hum In w w .u-u um- “ 11‘)! 1JM
SWITCHING MODE POWER SUPPLY
SPECIFICATION
11
11. Marking Drawing/铭牌示意图:
IDEALPOMCER G
SWITCHING MODE POWER SUPPLY
SPECIFICATION
12
12. Package Drawing/包装示意图:
MECHANICAL DIMENSION:
PAPER CASE/纸箱
CARDBOARD/纸板
WHITE BOX/白盒
PLASTIC BAG/PE袋
------ END ------
L(mm)
W(mm)
H(mm)
PLASTIC BAG
210
130
WHITE BOX
143
70
60
CARDBOARD
370
296
PAPER CASE
380
306
275
PACKING METHOD：
PACKING METHOD
10PCS/LAYER *4LAYERS
QTY
40PCS
N.W
11.0Kg
G.W
12.5Kg