LB Series Inductors Catalog Datasheet by Taiyo Yuden

View All Related Products | Download PDF Datasheet
TAIYO YUDEN 2020
20
REMINDERS
Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
Product Information in this Catalog
Product information in this catalog is as of October 2019. All of the
contents specified herein and production status of the products listed
in this catalog are subject to change without notice due to technical
improvement of our products, etc. Therefore, please check for the
latest information carefully before practical application or use of our
products.
Please note that TAIYO YUDEN shall not be in any way responsible
for any damages and defects in products or equipment incorporating
our products, which are caused under the conditions other than those
specified in this catalog or individual product specification sheets.
Approval of Product Specifications
Please contact TAIYO YUDEN for further det a ils of product
specifications as the individual product specification sheets are
available. When using our products, please be sure to approve our
product specifications or make a written agreement on the product
specification with TAIYO YUDEN in advance.
Pre-Evaluation in the Actual Equipment and Conditions
Please conduct validation and verification of our products in actual
conditions of mounting and operating environment before using our
products.
Limited Application
1. Equipment Intended for Use
The pro ducts listed in this c atalog are intended for general-
purpose and standard use in general electronic equipment (e.g.,
AV equipment, OA equipment, home electric appliances, office
equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and other equipment
specified in this catalog or the individual product specification sheets.
TAIYO YUDEN has the line-up of the products intended for
use in automotive electronic equipment, telecommunications
infrastructure and industrial equipment, or medical devices
classified as GHTF Classes A to C (Japan Classes I to III).
Therefore, whe n using our produ cts for these equipment,
please check available applications specified in this catalog
or the individual product specification sheets and use the
corresponding products.
2. Equipment Requiring Inquiry
Please be sure to contact TAIYO YUDEN for further information
before using the products listed in this catalog for the following
equipment (excluding intended equipment as specified in this
catalog or the individual product specification sheets) which may
cause loss of human life, bodily injury, serious property damage
and/or serious public impact due to a failure or defect of the
products and/or malfunction attributed thereto.
(1) Transportation equipment (automotive powertrain control
system, train control system, and ship control system, etc.)
(2) Traffic signal equipment
(3) Disaster prevention equipment, crime prevention equipment
(4) Medical devices classified as GHTF Class C (Japan Class III)
(5) Highly public information network equipment, data-
processing equipment (telephone exchange, and base
station, etc.)
(6) Any other equipment requiring high levels of quality and/or
reliability equal to the equipment listed above
3. Equipment Prohibited for Use
Please do not incorporate our products into the following
equipment requiring extremely high levels of safet y and/or
reliability.
(1) Aerospace equipment (artificial satellite, rocket, etc.)
(2) Aviation equipment *1
(3) Medical devices classified as GHTF Class D (Japan Class IV),
implantable medical devices *2
(4) Power generation control equip ment (nuclear power,
hydroelectric power, thermal power plant control system, etc.)
(5) Undersea equipment (submarine repeating equipment,
underwater work equipment, etc.)
(6) Military equipment
(7) Any other equipment requiring extremely high levels of safety
and/or reliability equal to the equipment listed above
*Notes:
1. There is a possibility that our products can be used only
for aviation equipment that does not directly affect the safe
operation of aircraft (e.g., in-flight entertainment, cabin
light, electric seat, cooking equipment) if such use meets
requirements specified separately by TAIYO YUDEN. Please
be sure to contact TAIYO YUDEN for further information
before using our products for such aviation equipment.
2. Implantable medical devices contain not only internal unit
which is implanted in a body, but also external unit which is
connected to the internal unit.
4. Limitation of Liability
Please note that unless you obtain prior written consent of TAIYO
YUDEN, TAIYO YUDEN shall not be in any way responsible for
any damages incurred by you or third parties arising from use of
the products listed in this catalog for any equipment that is not
intended for use by TAIYO YUDEN, or any equipment requiring
inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN
as described above.
Safety Design
When using our products for high safety and/or reliability-required
equipment or circuits, please fully perform safety and/or reliability
evaluation. In addition, please install (i) systems equipped with
a protection circuit and a protection device and/or (ii) systems
equipped with a redundant circuit or other system to prevent an
unsafe status in the event of a single fault for a failsafe design to
ensure safety.
Intellectual Property Rights
Information contained in this catalog is intended to convey examples
of typical performances and/or applications of our products and is
not intended to make any warranty with respect to the intellectual
property rights or any other related rights of TAIYO YUDEN or any
third parties nor grant any license under such rights.
Limited Warranty
Please note that the scope of warranty for our products is limited to
the delivered our products themselves and TAIYO YUDEN shall not
be in any way responsible for any damages resulting from a failure
or defect in our products. Notwithstanding the foregoing, if there is
a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company,
TAIYO YUDEN will warrant our products in accordance with such
agreement.
TAIYO YUDEN’s Official Sales Channel
The contents of this catalog are applicable to our products which are
purchased from our sales offices or authorized distributors (hereinafter
TAIYO YUDENs official sales channel). Please note that the contents
of this catalog are not applicable to our products purchased from any
seller other than TAIYO YUDENs official sales channel.
Caution for Export
Some of our products listed in this catalog may require specific
procedures for export according to U.S. Export Administration
Regulations, Foreign Exchange and Foreign Trade Control Law
of Japan, and other applicable regulations. Should you have any
questions on this matter, please contact our sales staff.
\ H H H:H H:||:H TAIYD YUDEN 2020
82
20
for General Electronic Equipmentfor General Electronic Equipment
i_wound_LB_e-E08R01
WIRE-WOUND CHIP INDUCTORSLB SERIES
REFLOW
PARTS NUMBER * Operating Temp.:-40~+105℃(Including self-generated heat)
L B 2 0 1 2 T 1 0 0 M △=Blank space
①Series name
Code Series name
LB Wound chip inductor
②Characteristics
Code Characteristics
△△ Standard
△C High current
△R Low Rdc
MF Low loss
③Dimensions(L×W)
Code Type(inch) Dimensions
(L×W)[mm]
1608 1608(0603) 1.6×0.8
2012 2012(0805) 2.0×1.25
2016 2016(0806) 2.0×1.6
2518 2518(1007) 2.5×1.8
3218 3218(1207) 3.2×1.8
3225 3225(1210) 3.2×2.5
④Packaging
Code Packaging
T Taping
⑤Nominal inductance
Code
(example) Nominal inductance[μH]
1R0 1.0
100 10
101 100
※R=Decimal point
⑥Inductance tolerance
Code Inductance tolerance
K ±10%
M ±20%
⑦Special code
Code Special code
Standard
R Low Rdc type
⑧Internal code
STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
LB/LB C/LB R LBMF
Recommended Land Patterns
Surface Mounting
・Mounting and soldering conditions should be checked beforehand.
・Applicable soldering process to these products is reflow soldering only.
W
L
e
T
W
L
e
T
AAB
C
Type A B C
1608 0.55 0.7 0.9
MF1608 0.55 0.7 1.0
2012 0.60 1.0 1.45
2016 0.60 1.0 1.8
2518 0.60 1.5 2.0
3218 0.85 1.7 2.0
3225 0.85 1.7 2.7
Unit:mm
Type L W T e Standard quantity[pcs]
Paper tape Embossed tape
LB 1608 1.6±0.1
(0.063±0.004)
0.8±0.1
(0.031±0.004)
0.8±0.1
(0.031±0.004)
0.35±0.15
(0.014±0.006) 4000
LBMF1608 1.6±0.2
(0.063±0.008)
0.8±0.2
(0.031±0.008)
0.8±0.2
(0.031±0.008)
0.45±0.15
(0.016±0.006) 3000
LB 2012
LB C2012
LB R2012
2.0±0.2
(0.079±0.008)
1.25±0.2
(0.049±0.008)
1.25±0.2
(0.049±0.008)
0.5±0.2
(0.020±0.008) 3000
LB 2016
LB C2016
2.0±0.2
(0.079±0.008)
1.6±0.2
(0.063±0.008)
1.6±0.2
(0.063±0.008)
0.5±0.2
(0.020±0.008) 2000
LB 2518
LB C2518
LB R2518
2.5±0.2
(0.098±0.008)
1.8±0.2
(0.071±0.008)
1.8±0.2
(0.071±0.008)
0.5±0.2
(0.020±0.008) 2000
LB 3218 3.2±0.2
(0.126±0.008)
1.8±0.2
(0.071±0.008)
1.8±0.2
(0.071±0.008)
0.6±0.2
(0.024±0.008) 2000
LB C3225 3.2±0.2
(0.126±0.008)
2.5±0.2
(0.098±0.008)
2.5±0.2
(0.098±0.008)
0.6±0.3
(0.024±0.012) 1000
Unit:mm(inch)
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
INDUCTORS STANDARD INDUCTORS
WIRE-WOUND CHIP INDUCTORS (LB SERIES)
REFLOW
TAIYO YUDEN 2020
83
20
for General Electronic Equipment
PARTS NUMBER
1608(0603)type
LB 1608T1R0M RoHS 1.0 ±20% 100 0.17 160 7.96
LB 1608T2R2M RoHS 2.2 ±20% 80 0.33 115 7.96
LB 1608T4R7M RoHS 4.7 ±20% 45 0.55 70 7.96
LB 1608T8R2M RoHS 8.2 ±20% 32 0.70 60 2.52
LB 1608T100M RoHS 10 ±20% 32 0.70 60 2.52
LBMF1608T1R0M RoHS 1.0 ±20% 100 0.09 230 7.96
LBMF1608T2R2M RoHS 2.2 ±20% 80 0.17 160 7.96
LBMF1608T3R3M RoHS 3.3 ±20% 60 0.22 130 7.96
LBMF1608T4R7M RoHS 4.7 ±20% 45 0.24 110 7.96
LBMF1608T100[] RoHS 10 ±10%,±20 32 0.36 80 2.52
LBMF1608T220[] RoHS 22 ±10%,±20 16 1.0 50 2.52
LBMF1608T470[] RoHS 47 ±10%,±20 11 2.5 35 2.52
2012(0805)type
LB 2012T1R0M RoHS 1.0 ±20% 100 0.15 405 7.96
LB 2012T2R2M RoHS 2.2 ±20% 80 0.23 260 7.96
LB 2012T3R3M RoHS 3.3 ±20% 55 0.30 235 7.96
LB 2012T4R7M RoHS 4.7 ±20% 45 0.40 190 7.96
LB 2012T6R8M RoHS 6.8 ±20% 38 0.47 135 7.96
LB 2012T100[] RoHS 10 ±10%,±20% 32 0.70 120 2.52
LB 2012T100[]R RoHS 10 ±10%,±20 32 0.50 120 2.52
LB 2012T150[] RoHS 15 ±10%,±20% 28 1.3 100 2.52
LB 2012T220[] RoHS 22 ±10%,±20% 16 1.7 80 2.52
LB 2012T470[] RoHS 47 ±10%,±20% 11 3.7 60 2.52
LB 2012T680[] RoHS 68 ±10%,±20% 10 6.0 50 2.52
LB 2012T101[] RoHS 100 ±10%,±20 8 7.0 45 0.796
LB C2012T1R0M RoHS 1.0 ±20% 100 0.19 620 7.96
LB C2012T2R2M RoHS 2.2 ±20% 70 0.33 430 7.96
LB C2012T4R7M RoHS 4.7 ±20% 45 0.50 295 7.96
LB C2012T100[] RoHS 10 ±10%,±20 40 1.2 200 2.52
LB C2012T220[] RoHS 22 ±10%,±20 16 3.7 130 2.52
LB C2012T470[] RoHS 47 ±10%,±20 11 5.8 90 2.52
LB R2012T1R0M RoHS 1.0 ±20% 100 0.07 400 7.96
LB R2012T2R2M RoHS 2.2 ±20% 80 0.13 260 7.96
LB R2012T4R7M RoHS 4.7 ±20% 45 0.24 200 7.96
LB R2012T100[] RoHS 10 ±10%,±20% 32 0.36 150 2.52
LB R2012T220[] RoHS 22 ±10%,±20% 16 1.0 100 2.52
LB R2012T470[] RoHS 47 ±10%,±20% 11 1.7 75 2.52
LB R2012T101[] RoHS 100 ±10%,±20% 8 4.0 50 0.796
2016(0806)type
LB 2016T1R0M RoHS 1.0 ±20% 100 0.09 490 7.96
LB 2016T1R5M RoHS 1.5 ±20% 80 0.11 380 7.96
LB 2016T2R2M RoHS 2.2 ±20% 70 0.13 375 7.96
LB 2016T3R3M RoHS 3.3 ±20% 55 0.20 285 7.96
LB 2016T4R7M RoHS 4.7 ±20% 45 0.25 225 7.96
LB 2016T6R8M RoHS 6.8 ±20% 38 0.35 200 7.96
LB 2016T100[] RoHS 10 ±10%,±20% 32 0.50 155 2.52
LB 2016T150[] RoHS 15 ±10%,±20% 28 0.70 130 2.52
LB 2016T220[] RoHS 22 ±10%,±20% 16 1.0 105 2.52
LB 2016T330[] RoHS 33 ±10%,±20% 14 1.7 85 2.52
LB 2016T470[] RoHS 47 ±10%,±20% 11 2.4 70 2.52
LB 2016T680[] RoHS 68 ±10%,±20% 10 3.0 55 2.52
LB 2016T101[] RoHS 100 ±10%,±20 8 4.5 40 0.796
・ [] Please specify the Inductance tolerance code(K or M)
LB/LBC series
Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias.
LBR series
Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias.
Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current
[mA](max.)
Measuring frequency
[MHz]
Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Nominal inductance
[μH] Inductance tolerance
Parts number EHS Nominal inductance
[μH] Inductance tolerance
Rated current
[mA](max.)
Measuring frequency
[MHz]
Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current
[mA](max.)
Measuring frequency
[MHz]
Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current
[mA](max.)
Measuring frequency
[MHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance
Parts number EHS Nominal inductance
[μH] Inductance tolerance
Parts number EHS
Measuring frequency
[MHz]
Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Parts number EHS Nominal inductance
[μH] Inductance tolerance Rated current
[mA](max.)
Rated current
[mA](max.)
Measuring frequency
[MHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
i_wound_LB_e-E08R01
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
INDUCTORS STANDARD INDUCTORS
TAIYO YUDEN 2020
84
20
for General Electronic Equipment
PARTS NUMBER
LB C2016T1R0M RoHS 1.0 ±20% 100 0.10 690 7.96
LB C2016T1R5M RoHS 1.5 ±20% 80 0.15 600 7.96
LB C2016T2R2M RoHS 2.2 ±20% 70 0.20 520 7.96
LB C2016T3R3M RoHS 3.3 ±20% 55 0.27 410 7.96
LB C2016T4R7M RoHS 4.7 ±20% 45 0.37 355 7.96
LB C2016T6R8M RoHS 6.8 ±20% 38 0.59 290 7.96
LB C2016T100[] RoHS 10 ±10%,±20 32 0.82 245 2.52
LB C2016T150[] RoHS 15 ±10%,±20 28 1.2 200 2.52
LB C2016T220[] RoHS 22 ±10%,±20 16 1.8 165 2.52
LB C2016T330[] RoHS 33 ±10%,±20 14 2.8 135 2.52
LB C2016T470[] RoHS 47 ±10%,±20 11 4.3 110 2.52
LB C2016T680[] RoHS 68 ±10%,±20 10 7.0 95 2.52
LB C2016T101[] RoHS 100 ±10%,±20% 8 8.0 75 0.796
2518(1007)type
LB 2518T1R0M RoHS 1.0 ±20% 100 0.06 665 7.96
LB 2518T1R5M RoHS 1.5 ±20% 80 0.07 405 7.96
LB 2518T2R2M RoHS 2.2 ±20% 68 0.09 340 7.96
LB 2518T3R3M RoHS 3.3 ±20% 54 0.11 280 7.96
LB 2518T4R7M RoHS 4.7 ±20% 46 0.13 240 7.96
LB 2518T4R7MR RoHS 4.7 ±20% 46 0.10 235 7.96
LB 2518T6R8M RoHS 6.8 ±20% 38 0.15 195 7.96
LB 2518T100[] RoHS 10 ±10%,±20% 30 0.25 165 2.52
LB 2518T150[] RoHS 15 ±10%,±20% 23 0.32 145 2.52
LB 2518T220[] RoHS 22 ±10%,±20% 19 0.50 115 2.52
LB 2518T330[] RoHS 33 ±10%,±20% 15 0.70 95 2.52
LB 2518T470[] RoHS 47 ±10%,±20% 12 0.95 85 2.52
LB 2518T680[] RoHS 68 ±10%,±20% 9.5 1.5 70 2.52
LB 2518T101[] RoHS 100 ±10%,±20 9.0 2.1 60 0.796
LB 2518T151[] RoHS 150 ±10%,±20 7.0 3.2 45 0.796
LB 2518T221[] RoHS 220 ±10%,±20 5.5 4.5 40 0.796
LB 2518T331[] RoHS 330 ±10%,±20 4.5 7.0 30 0.796
LB 2518T471[] RoHS 470 ±10%,±20 3.5 10 25 0.796
LB 2518T681[] RoHS 680 ±10%,±20 3.0 17 20 0.796
LB 2518T102[] RoHS 1000 ±10%,±20% 2.4 24 15 0.252
LB C2518T1R0M RoHS 1.0 ±20% 100 0.08 775 7.96
LB C2518T1R0MR RoHS 1.0 ±20% 100 0.07 890 7.96
LB C2518T1R5M RoHS 1.5 ±20% 80 0.11 730 7.96
LB C2518T2R2M RoHS 2.2 ±20% 68 0.13 630 7.96
LB C2518T3R3M RoHS 3.3 ±20% 54 0.16 560 7.96
LB C2518T4R7M RoHS 4.7 ±20% 41 0.20 510 7.96
LB C2518T6R8M RoHS 6.8 ±20% 38 0.30 420 7.96
LB C2518T100[] RoHS 10 ±10%,±20 30 0.36 375 2.52
LB C2518T150[] RoHS 15 ±10%,±20 23 0.65 285 2.52
LB C2518T220[] RoHS 22 ±10%,±20 19 0.77 250 2.52
LB C2518T330[] RoHS 33 ±10%,±20 15 1.5 185 2.52
LB C2518T470[] RoHS 47 ±10%,±20 12 1.9 165 2.52
LB C2518T680[] RoHS 68 ±10%,±20 9.5 2.8 140 2.52
LB C2518T101[] RoHS 100 ±10%,±20% 9.0 3.7 125 0.796
LB C2518T151[] RoHS 150 ±10%,±20% 7.0 6.1 95 0.796
LB C2518T221[] RoHS 220 ±10%,±20% 5.5 8.4 80 0.796
LB C2518T331[] RoHS 330 ±10%,±20% 4.5 12.3 65 0.796
LB C2518T471[] RoHS 470 ±10%,±20% 3.5 22 50 0.796
LB C2518T681[] RoHS 680 ±10%,±20% 3.0 28 45 0.796
LB R2518T1R0M RoHS 1.0 ±20% 100 0.045 960 7.96
LB R2518T2R2M RoHS 2.2 ±20% 68 0.07 480 7.96
LB R2518T4R7M RoHS 4.7 ±20% 45 0.10 345 7.96
LB R2518T100[] RoHS 10 ±10%,±20% 30 0.19 235 2.52
LB R2518T220[] RoHS 22 ±10%,±20% 19 0.44 175 2.52
LB R2518T470[] RoHS 47 ±10%,±20% 11 0.84 120 2.52
LB R2518T101[] RoHS 100 ±10%,±20% 9 1.89 80 0.796
・ [] Please specify the Inductance tolerance code(K or M)
LB/LBC series
Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias.
LBR series
Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias.
Rated current
[mA](max.)
Measuring frequency
[MHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current
[mA](max.)
Measuring frequency
[MHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current
[mA](max.)
Measuring frequency
[MHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current
[mA](max.)
Measuring frequency
[MHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
i_wound_LB_e-E08R01
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
INDUCTORS STANDARD INDUCTORS
TAIYO YUDEN 2020
85
20
for General Electronic Equipment
PARTS NUMBER
3218(1207)type
LB 3218T1R0M RoHS 1.0 ±20% 100 0.06 1,075 7.96
LB 3218T1R5M RoHS 1.5 ±20% 80 0.07 860 7.96
LB 3218T2R2M RoHS 2.2 ±20% 68 0.09 775 7.96
LB 3218T3R3M RoHS 3.3 ±20% 54 0.11 560 7.96
LB 3218T4R7M RoHS 4.7 ±20% 41 0.13 550 7.96
LB 3218T6R8M RoHS 6.8 ±20% 40 0.17 380 7.96
LB 3218T100[] RoHS 10 ±10%,±20% 30 0.25 340 2.52
LB 3218T150[] RoHS 15 ±10%,±20% 25 0.32 300 2.52
LB 3218T220[] RoHS 22 ±10%,±20% 19 0.49 255 2.52
LB 3218T330[] RoHS 33 ±10%,±20% 15 0.75 215 2.52
LB 3218T470[] RoHS 47 ±10%,±20% 12 0.92 205 2.52
LB 3218T680[] RoHS 68 ±10%,±20% 11 1.49 145 2.52
LB 3218T101[] RoHS 100 ±10%,±20 8.0 2.4 140 0.796
LB 3218T151[] RoHS 150 ±10%,±20 7.0 3.2 105 0.796
LB 3218T221[] RoHS 220 ±10%,±20 5.0 5.4 80 0.796
LB 3218T331[] RoHS 330 ±10%,±20 4.0 7.0 65 0.796
LB 3218T471[] RoHS 470 ±10%,±20 3.5 14 54 0.796
LB 3218T681[] RoHS 680 ±10%,±20 3.0 17 45 0.796
LB 3218T102[] RoHS 1000 ±10%,±20% 2.4 27 39 0.252
3225(1210)type
LB C3225T1R0MR RoHS 1.0 ±20% 250 0.055 1,100 0.1
LB C3225T1R5MR RoHS 1.5 ±20% 220 0.060 1,000 0.1
LB C3225T2R2MR RoHS 2.2 ±20% 190 0.080 930 0.1
LB C3225T3R3MR RoHS 3.3 ±20% 160 0.095 820 0.1
LB C3225T4R7MR RoHS 4.7 ±20% 70 0.100 680 0.1
LB C3225T6R8MR RoHS 6.8 ±20% 50 0.120 620 0.1
LB C3225T100[]R RoHS 10 ±10%,±20 23 0.133 540 0.1
LB C3225T150[]R RoHS 15 ±10%,±20 20 0.195 420 0.1
LB C3225T220[]R RoHS 22 ±10%,±20 17 0.27 330 0.1
LB C3225T330[]R RoHS 33 ±10%,±20 13 0.41 300 0.1
LB C3225T470[]R RoHS 47 ±10%,±20 10 0.67 220 0.1
LB C3225T680[]R RoHS 68 ±10%,±20 8 1.0 190 0.1
LB C3225T101[]R RoHS 100 ±10%,±20% 6 1.4 150 0.1
・ [] Please specify the Inductance tolerance code(K or M)
LB/LBC series
Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias.
Rated current
[mA](max.)
Measuring frequency
[MHz]
Parts number EHS Nominal inductance
[μH] Inductance tolerance Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Parts number EHS Nominal inductance
[μH] Inductance tolerance Self-resonant frequency
[MHz](min.)
DC Resistance
[Ω](±30%)
Rated current
[mA](max.)
Measuring frequency
[MHz]
i_wound_LB_e-E08R01
Thiscatalogcontainsthetypicalspecificationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourproductspecificationsheets.
 Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourwebsite(http://www.ty-top.com/).
INDUCTORS STANDARD INDUCTORS
OO @1an hi \J‘a/ @- Ea} Sprocket hole 0 o 3 c o D U D E Bottom tape Chip cavity y“ TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
WIRE-WOUND CHIP INDUCTORS (LB SERIES),
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES),
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
PACKAGING
①Minimum Quantity
Type Standard Quantity [pcs]
Paper Tape Embossed Tape
LB C3225
CB C3225 1000
LB 3218 2000
LB R2518
LB C2518
LB 2518
CB 2518
CB C2518
2000
LBM2016
LB C2016
LB 2016
CB 2016
CB C2016
2000
LB 2012
LB C2012
LB R2012
CB 2012
CB C2012
3000
CB L2012 4000
LB 1608 4000
LBMF1608
CBMF1608 3000
②Tape material
Embossed tape
Top tape
Base tape
Sprocket hole
Chip cavity
Chip
Chip Filled
Card board carrier tape
Top tape
Base tape
Sprocket hole
Bottom tape Chip cavity
Chip
Chip Filled
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
③Taping Dimensions
Embossed Tape (0.315 inches wide)
F
2.0±0.1
(0.079±0.004)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
Type Chip cavity Insertion pitch Tape thickness
A B F T K
LBM2016 1.75±0.1
(0.069±0.004)
2.1±0.1
(0.083±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
1.9max.
(0.075max.)
LB C3225
CB C3225
2.8±0.1
(0.110±0.004)
3.5±0.1
(0.138±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
4.0max.
(0.157max.)
LB 3218 2.1±0.1
(0.083±0.004)
3.5±0.1
(0.138±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
2.2max.
(0.087max.)
LB 2518
CB 2518
LB C2518
CB C2518
LB R2518
2.15±0.1
(0.085±0.004)
2.7±0.1
(0.106±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
2.2max.
(0.087max.)
LB 2016
CB 2016
LB C2016
CB C2016
1.75±0.1
(0.069±0.004)
2.1±0.1
(0.083±0.004)
4.0±0.1
(0.157±0.004)
0.3±0.05
(0.012±0.002)
1.9max.
(0.075max.)
LB 2012
CB 2012
LB C2012
CB C2012
LB R2012
1.45±0.1
(0.057±0.004)
2.25±0.1
(0.089±0.004)
4.0±0.1
(0.157±0.004)
0.25±0.05
(0.010±0.002)
1.45max.
(0.057max.)
LBMF1608
CBMF1608
1.1±0.1
(0.043±0.004)
1.9±0.1
(0.075±0.004)
4.0±0.1
(0.157±0.004)
0.25±0.05
(0.010±0.002)
1.2max.
(0.047max.)
Unit:mm(inch)
Card board carrier tape(0.315 inches wide)
F
2.0±0.1
(0.079±0.004)
4.0±0.1
(0.157±0.004)
1.75±0.1
(0.069±0.004)
3.5±0.05
(0.138±0.002)
8.0±0.3
(0.315±0.012)
φ1.5+0.1/-0
(φ0.059+0.004/-0)
Sprocket hole
A
B
T
Type Chip cavity Insertion pitch Tape thickness
A B F T
CB L2012 1.55±0.1
(0.061±0.004)
2.3±0.1
(0.091±0.004)
4.0±0.1
(0.157±0.004)
1.1max.
(0.043max.)
LB 1608 1.0±0.1
(0.039±0.004)
1.8±0.1
(0.071±0.004)
4.0±0.1
(0.157±0.004)
1.1max.
(0.043max.)
Unit:mm(inch)
Blank ponlnns Chip cavity Blank ponions Loaaur 7 00000 HHI i u°n O 1 5H 4 L—J (1(1than (lupinhammom) 1mfl.“ Direction 0! (5.9 Indus of me) tape «zed R2910 5 _ o. ,0:th 21+a.c:n) ID 0115 (0.39420 0501 Pull dilection Tap tape / 5mm» TAIYCI YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
④Leader and Blank Portion
⑤Reel Size
⑥Top Tape Strength
The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
WIRE-WOUND CHIP INDUCTORS (LB SERIES),
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES),
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
RELIABILITY DATA
1.Operating temperature Range
Specified Value
LB, LBC, LBR, LBMF Series
-40~+105℃(Including self-generated heat)
CB, CBC, CBL, CBMF Series
LBM Series
2. Storage Temperature Range(after soldering)
Specified Value
LB, LBC, LBR, LBMF Series
-40~+85℃ CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
LB, CB Series:
Please refer the term of "7. storage conditions" in precautions.
3.Rated Current
Specified Value
LB, LBC, LBR, LBMF Series
Within the specified tolerance CB, CBC, CBL, CBMF Series
LBM Series
4.Inductance
Specified Value
LB, LBC, LBR, LBMF Series
Within the specified tolerance CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series
Measuring equipment :LCR Mater(HP4285A or its equivalent)
Measuring frequency : Specified frequency
5.Q
Specified Value
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series Within the specified tolerance
Test Methods and
Remarks
LBM Series
Measuring equipment : LCR Mater(HP4285A or its equivalent)
Measuring frequency : Specified frequency
6.DC Resisitance
Specified Value
LB, LBC, LBR, LBMF Series
Within the specified tolerance CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks Measuring equipment : DC Ohmmeter (HIOKI 3227 or its equivalent
7.Self-Resonant Frequency
Specified Value
LB, LBC, LBR, LBMF Series
Within the specified tolerance CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks Measuring equipment : Impedance analyzer (HP4291A or its equivalent)
Pressmg jig 20 ‘T fl H340 J, J v‘ Board ‘ , A v . , v ‘ Rs maymwmj \ TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
8.Temperature Characteristic
Specified Value
LBM2016 Inductance change : Within±5%
LB1608 LB2012 LBR2012 CB2012
Inductance change : Within±20%
CBL2012 LB2016 CB2016 LB2518
LBR2518 CB2518 LBC3225 CBC3225
LBMF1608 CBMF1608 LBC2016 CBC2016 Inductance change : Within±25%
LBC2518 CBC2518 LB3218
LBC2012 CBC2012 Inductance change : Within±35%
Test Methods and
Remarks Based on the inductance at 20℃ and Measured at the ambient of 40℃~+85℃.
9.Rasistance to Flexure of Substrate
Specified Value
LB, LBC, LBR, LBMF Series
No damage. CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
Warp : 2mm(LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series)
Test substrate : Glass epoxy-resin substrate
Thickness : 0.8mm(LB1608・LBMF1608・CBMF1608)
: 1.0mm(Others)
10.Body Strength
Specified Value
LB, LBC, LBR, LBMF Series
No damage. CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM
Applied force : 10N
Duration : 10sec.
LB1608・LBMF1608・CBMF1608
Applied force : 5N
Duration : 10sec.
11.Adhesion of terminal electrode
Specified Value
LB, LBC, LBR, LBMF Series
No abnormality. CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF
Applied force : 10N to X and Y directions
Duration : 5 sec.
Test substrate : Printed board
LB1608・CBMF1608・LBMF1608
Applied force : 5N to X and Y directions
Duration : 5 sec.
Test substrate : Printed board
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
12.Resistance to vibration
Specified Value
LB, LBC, LBR, LBMF Series Inductance change : Within±10%
No significant abnormality in appearance.
CB, CBC, CBL, CBMF Series
LBM Series Inductance change : Within±5%
No significant abnormality in appearance.
Test Methods and
Remarks
LB・LBR・LBC・CB・CBC・CBL・LBM・LBMF・CBMF:
The given sample is soldered to the board and then it is tested depending on the conditions of the following table.
Vibration Frequency 10~55Hz
Total Amplitude 1.5mm (May not exceed acceleration 196m/s2)
Sweeping Method 10Hz to 55Hz to 10Hz for 1min.
Time
X
For 2 hours on each X, Y, and Z axis. Y
Z
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
13.Drop test
Specified Value
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
14.Solderability
Specified Value
LB, LBC, LBR, LBMF Series
At least 90% of surface of terminal electrode is covered by new CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF:
Solder temperature : 245±5℃
Duration : 5±0.5sec
Flux : Methanol solution with 25% of colophony
15.Resistance to soldering
Specified Value
LB, LBC, LBR, LBMF Series Inductance change : Within±10%
CB, CBC, CBL, CBMF Series
LBM Series Inductance change : Within±5%
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF:
3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 for 5sec.
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
16.Resisitance to solvent
Specified Value
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
Solvent temperature : Room temperature
Type of solvent : Isopropyl alcohol
Cleaning conditions : 90s. Immersion and cleaning.
17.Thermal shock
Specified Value
LB, LBC, LBR, LBMF Series
Inductance change : Within±10%
No significant abnormality in appearance.
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF:
The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions.
Conditions of 1 cycle
Step Temperature (℃) Duration (min)
1 -40±3 30±3
2 Room temperature Within 3
3 +85±2 30±3
4 Room temperature Within 3
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
18.Damp heat life test
Specified Value
LB, LBC, LBR, LBMF Series
Inductance change : Within±10%
No significant abnormality in appearance.
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
Temperature : 60±2℃
Humidity : 90~95%RH
Duration : 1000 hrs
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
19.Loading under damp heat life test
Specified Value
Test Methods and
Remarks
LB, LBC, LBR, LBMF Series
Inductance change : Within±10%
No significant abnormality in appearance.
CB, CBC, CBL, CBMF Series
LBM Series
Temperature : 60±2℃
Humidity : 90~95%RH
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
20.High temperature life test
Specified Value
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series Inductance change : Within±10%
No significant abnormality in appearance.
LBM Series
Test Methods and
Remarks
Temperature : 85±2℃
Duration : 1000 hrs
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
21.Loading at high temperature life test
Specified Value
LB, LBC, LBR, LBMF Series
Inductance change : Within±10%
(LBC3225 Series : Within±20%)
No significant abnormality in appearance.
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
Temperature : 85±2℃
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
22.Low temperature life test
Specified Value
LB, LBC, LBR, LBMF Series
Inductance change : Within±10%
No significant abnormality in appearance.
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
Temperature : -40±2℃
Duration : 1000 hrs
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
23.Standard condition
Specified Value
LB, LBC, LBR, LBMF Series Standard test conditions
Unless specified, Ambient temperature is 20±15 and the Relative
humidity is 65±20%. If there is any doubt about the test results, further
measurement shall be had within the following limits:
Ambient Temperature: 20±2℃
Relative humidity: 65±5%
Inductance value is based on our standard measurement systems.
CB, CBC, CBL, CBMF Series
LBM Series
Temperature[”c] 30D , 5590 max < peak'="" 150~1eo="" 260+0/*5"c="" 200="" »="" .="" ,="" gui‘dsec="" ‘00="" ’="" 90:30$ec="" mm="" mm="" heating="" twme="" [sec]="" taiyo="" yuden="">
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_prec_e-E06R01
WIRE-WOUND CHIP INDUCTORS (LB SERIES),
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES),
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
PRECAUTIONS
1.Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2.PCB Design
Precautions ◆Land pattern design
1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications.
Technical
considerations
PRECAUTIONS
【Recommended Land Patterns】
Surface Mounting
Mounting and soldering conditions should be checked beforehand.
Applicable soldering process to those products is reflow soldering only.
3.Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
considerations 1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4.Soldering
Precautions
◆Reflow soldering( LB and CB Types)
1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended.
◆Recommended conditions for using a soldering iron
1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron
should not come in contact with inductor directly.
Technical
considerations
◆Reflow soldering( LB and CB Types)
1. Reflow profile
◆Recommended conditions for using a soldering iron
1. Components can be damaged by excessive heat where soldering conditions exceed the specified range.
5.Cleaning
Precautions ◆Cleaning conditions
Washing by supersonic waves shall be avoided.
Technical
considerations
◆Cleaning conditions
If washed by supersonic waves, the products might be broken.
TAIYO YUDEN
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_prec_e-E06R01
6.Handling
Precautions
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Breakaway PC boards( splitting along perforations)
1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the
board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
Technical
considerations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Breakaway PC boards( splitting along perforations)
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
7.Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
Recommended conditions
Ambient temperature : 0~40℃
Humidity : Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, product should be used within 6 months from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.

Products related to this Datasheet

FIXED IND 22UH 100MA 1 OHM SMD
Available Quantity: 195,000
Unit Price: 0.0495
FIXED IND 1UH 960MA 45 MOHM SMD
Available Quantity: 16,000
Unit Price: 0.06468
FIXED IND 47UH 120MA 840MOHM SMD
Available Quantity: 14,000
Unit Price: 0.06468
FIXED IND 10UH 150MA 360MOHM SMD
Available Quantity: 12,000
Unit Price: 0.0495
FIXED IND 10UH 235MA 190MOHM SMD
Available Quantity: 12,000
Unit Price: 0.06468
FIXED IND 100UH 50MA 4 OHM SMD
Available Quantity: 3,000
Unit Price: 0.0495
FIXED IND 47UH 75MA 1.7 OHM SMD
Available Quantity: 3,000
Unit Price: 0.0495
FIXED IND 2.2UH 115MA 330 MOHM
Available Quantity: 3,000
Unit Price: 0.25
FIXED IND 10UH 150MA 360MOHM SMD
Available Quantity: 0
Unit Price: 0.0495
FIXED IND 68UH 140MA 2.8 OHM SMD
Available Quantity: 2,000
Unit Price: 0.07623
FIXED IND 100UH 80MA 1.89OHM SMD
Available Quantity: 2,000
Unit Price: 0.06607
FIXED IND 47UH 120MA 840MOHM SMD
Available Quantity: 2,000
Unit Price: 0.06607
FIXED IND 4.7UH 345MA 100MOHM SM
Available Quantity: 2,000
Unit Price: 0.06468
FIXED IND 220UH 40MA 4.5 OHM SMD
Available Quantity: 17,474
Unit Price: 0.16
FIXED IND 4.7UH 70MA 550MOHM SMD
Available Quantity: 12,750
Unit Price: 0.27
FIXED IND 150UH 45MA 3.2 OHM SMD
Available Quantity: 2,657
Unit Price: 0.16
FIXED IND 2.2UH 340MA 90MOHM SMD
Available Quantity: 88
Unit Price: 0.16
FIXED IND 680UH 45MA 28 OHM SMD
Available Quantity: 0
Unit Price: 0.0693
FIXED IND 680UH 45MA 28 OHM SMD
Available Quantity: 0
Unit Price: 0.07623
FIXED IND 6.8UH 420MA 300MOHM SM
Available Quantity: 0
Unit Price: 0.07623
FIXED IND 22UH 100MA 1 OHM SMD
Available Quantity: 0
Unit Price: 0.0495
FIXED IND 10UH 235MA 190MOHM SMD
Available Quantity: 0
Unit Price: 0.06307
FIXED IND 22UH 175MA 440MOHM SMD
Available Quantity: 0
Unit Price: 0.06307
FIXED IND 2.2UH 480MA 70MOHM SMD
Available Quantity: 0
Unit Price: 0.06468
FIXED IND 47UH 75MA 1.7 OHM SMD
Available Quantity: 0
Unit Price: 0.0495
FIXED IND 100UH 50MA 4 OHM SMD
Available Quantity: 0
Unit Price: 0.0495
FIXED IND 22UH 175MA 440MOHM SMD
Available Quantity: 0
Unit Price: 0.06607
FIXED IND 100UH 80MA 1.89OHM SMD
Available Quantity: 0
Unit Price: 0.06468
FIXED IND 8.2UH 60MA 700 MOHM
Available Quantity: 4,000
Unit Price: 0.25
FIXED IND 22UH 115MA 500MOHM SMD
Available Quantity: 2,000
Unit Price: 0.14