UPB1509GV Datasheet by CEL

PART NUMBER UPB1509GV
PACKAGE OUTLINE S08
SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX
ICC Supply Current, No Input Signal, Vcc = 3 V mA 3.5 5.0 5.9
fIN (u) Upper Limit Operating Frequency, PIN = -20 to 0 dBm MHz 500
PIN = -20 to -5 dBm at ÷ 2 MHz 700
at ÷ 4 MHz 800
at ÷ 8 MHz 1000
fIN (L) Lower Limit Operating Frequency, PIN = -20 to 0 dBm MHz 50
PIN = -20 to -5 dBm MHz 500
PIN Input Power, fIN = 50 to 1000 MHz dBm -20 -5
fIN = 50 to 500 MHz dBm -20 0
VOUT Output Voltage, RL = 200 VP-P 0.1 0.2
VIN(H) Division Ratio Control Voltage High V VCC
VIN(L) Division Ratio Control Voltage Low V OPEN
NEC's 1.0 GHz
DIVIDE BY 2/4/8 PRESCALER
FEATURES
HIGH FREQUENCY OPERATION TO 1 GHz
SELECTABLE DIVIDE RATIO: ÷2, ÷4, ÷8
WIDE SUPPLY VOLTAGE RANGE: 2.2 TO 5 V
LOW SUPPLY CURRENT: 5.3 mA
SMALL PACKAGE: 8 pin SSOP
AVAILABLE IN TAPE AND REEL
DESCRIPTION
NEC's UPB1509GV is a Silicon RFIC digital prescaler manu-
factured with the NESAT IV silicon bipolar process. It fea-
tures frequency response to 1 GHz, selectable divide-by-two,
four, or eight modes, and operates from a 3 to 5 volt supply
while drawing only 5.3 milliamps. The device is housed in a
small 8 pin SSOP package that contributes to system miniatur-
ization. The low power consumption and wide supply range
makes the device well suited for cellular and cordless tele-
phones as well as DBS receiver applications.
TEST CIRCUIT
BIPOLAR DIGITAL INTEGRATED CIRCUIT
UPB1509GV
VCC
CC
C
C
C
C
C
C = 1000 pF
1
2
3
4
8
7
6
5
V
OUT
f
IN
V
CC1
IN
IN
GND
V
CC2
OUT
SW2
SW1
The information in this document is subject to change without notice. Before using this document, please confirm
that this is the latest version.
ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 2.2 to 5.5 V, unless otherwise noted)
Date Published: June 28, 2005
.California Eastern Laboratories
Pin No. Symbol Applied Pin Description
Voltage Voltage
1VCC1 2.2 to 5.5 Power supply pin of input amplifier and dividers. This pin must be
equipped with bypass capacitor (eg 1000 pF) to ground.
2 IN 1.7 to 4.95 Signal input pin. This pin should be coupled with a capacitor (eg 1000 pF).
3 IN 1.7 to 4.95 Signal input bypass pin. This pin must be equipped with a bypass
capacitor (eg 1000 pF) to ground.
4GND 0 Ground pin. Ground pattern on the board should be formed as wide as
possible to minimize ground impedance.
5SW1 H/L Divided ratio control pin. Divide ratio can be controlled by the following
(VCC/OPEN) input voltages to these pins.
6SW2 H/L
(VCC/OPEN)
These pins must each be equipped with a bypass capacitor to ground.
7OUT 1.0 to 4.7 Divided frequency output pin. This pin is designed as an emitter follower
output. This pin can output 0.1 Vp-p min with a 200 load.
This pin should be coupled to load device with a capacitor (eg 1000 pF).
8VCC2 2.2 to 5.5 Power supply pin of output buffer amplifier. This pin must be equipped
with bypass capacitor (eg 1000 pF) to ground.
SYMBOLS PARAMETERS UNITS RATINGS
VCC1, VCC2 Supply Voltage V 6.0
VIN Input Voltage V 6.0
PDPower Dissipation2mW 250
TOP Operating Temperature °C -45 to +85
TSTG Storage Temperature °C -55 to +150
ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) RECOMMENDED
OPERATING CONDITIONS
Notes:
1. Operation in excess of any one of these parameters may result
in permanent damage.
2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy
glass PWB (TA = +85˚C).
INTERNAL BLOCK DIAGRAM
SW2
H (VCC)L (OPEN)
H (VCC)1/2 1/4
SW1
L (OPEN) 1/4 1/8
PIN DESCRIPTIONS
IN
SW1 SW2
OUT
D
CLK
Q
IN Q
D
CLK
Q
Q
D
CLK
Q
Q
UPB1509GV
SYMBOL PARAMETER UNITS MIN TYP MAX
VCC1, VCC2 Supply Voltage V 2.2 3.0 5.5
TOP Operating Temperature °C-40 +25 +85
.California Eastern Laboratories
UPB1509GV
TYPICAL PERFORMANCE CURVES
(TA = +25°C unless otherwise noted)
Input Power, P
IN
(dBm)
9
8
7
6
5
4
3
2
1
0
01 23 45 6
Recommended operating range
T
A
= -40°C
T
A
= +25°C
T
A
= +85°C
T
A
= +25¡C
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
V
CC
= 5.5 V
V
CC
= 2.2 V
V
CC
= 3.0 V
V
CC
= 5.5 V V
CC
= 2.2 V
V
CC
= 3.0 V
Guaranteed
Operating Window
V
CC
= 3.0 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
T
A
= +25°C
T
A
= +85°C
T
A
= -40°C
Guaranteed
operating window
T
A
= +25°CT
A
= +85°C
T
A
= -40°C
V
CC
= 2.2 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
T
A
= +25°C
T
A
= +85°C
T
A
= -40°C
Guaranteed
operating window
T
A
= +25°C
T
A
= +85°CT
A
= -40°C
Supply Voltage, VCC (V)
Circuit Current, I
CC
(mA)
CIRCUIT CURRENT vs.
SUPPLY VOLTAGE and TEMPERATURE
Input Frequency, fin (MHz)
OutputVoltage Swing, V
P-P
(V)
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
Input Frequency, fin (MHz)
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Frequency, fin (MHz)
Input Power, P
IN
(dBm)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
V
CC
= 5.5 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
T
A
= +25°C
T
A
= +85°C
T
A
= -40°C
Guaranteed
operating window
T
A
= +85°C
T
A
= -40°C
T
A
= +25°C
T
A
= +85°C
T
A
= -40°C
T
A
= +85°C
T
A
= -40°C
T
A
= +25°C
T
A
= +25°C
V
CC
= 3.0 V
P
IN
= 0 dBm
0.3
0.2
0.1
0
2000
100
10 1000
Input Power, P
IN
(dBm)
Input Power, P
IN
(dBm)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
.California Eastern Laboraton'es
UPB1509GV
TYPICAL PERFORMANCE CURVES
(TA = +25°C unless otherwise noted)
T
A
= +25°C
P
IN
= 0 dBm
0.3
0.2
0.1
0
200010010 1000
V
CC
= 5.5 V
V
CC
= 2.2 V
V
CC
= 3.0 V
T
A
= -40°C
P
IN
= 0 dBm
0.3
0.2
0.1
0
200010010 1000
V
CC
= 5.5 V
V
CC
= 2.2 V
V
CC
= 3.0 V
T
A
= +85°C
P
IN
= 0 dBm
0.3
0.2
0.1
0
200010010 1000
V
CC
= 5.5 V
V
CC
= 2.2 V
V
CC
= 3.0 V
T
A
= +25ºC
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
V
CC
= 5.5 V
V
CC
= 5.5 V
V
CC
= 2.2 V
V
CC
= 3.0 V
Guaranteed
Operating Window
V
CC
= 3.0 V
V
CC
= 5.5 V
V
CC
= 2.2 V
Input Frequency, fin (MHz) Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Frequency, fin (MHz)
VCC = 3.0 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
TA = +25°C
TA = +85°C
TA = -40°C
Guaranteed
operating window
TA = +85°C
TA = -40°C
TA = +25°C
Input Power, P
IN
(dBm)
Input Power, P
IN
(dBm)
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
Input Frequency, fin (MHz)
OutputVoltage Swing, V
P-P
(V)
OutputVoltage Swing, V
P-P
(V)
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
Input Frequency, fin (MHz)
OutputVoltage Swing, V
P-P
(V)
OUTPUT VOLTAGE SWING vs.
INPUT FREQUENCY and VOLTAGE
Divide by 4 mode
(Guaranteed operating window: VCC = 2.2 to 5.5 V, TA = -40 to +85°C)
.Califomia Eastern Laboratories
UPB1509GV
V
CC
= 3.0 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
T
A
= +85°C
T
A
= -40°C
Guaranteed
operating window
T
A
= +85°C
T
A
= +25°C
T
A
= +25°C
T
A
= -40°C
TYPICAL PERFORMANCE CURVES
(TA = +25°C unless otherwise noted)
Input Power, P
IN
(dBm)
V
CC
= 5.5 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
T
A
= +85°C
T
A
= -40°C
Guaranteed
operating window
T
A
= +85°C
T
A
= +25°C
T
A
= -40°C
T
A
= -40°C
T
A
= +25°C
T
A
= +25°C
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
V
CC
= 2.2 V
V
CC
= 3.0 V
Guaranteed
Operating Window
V
CC
= 3.0 V
V
CC
= 5.5 V
V
CC
= 2.2 V
V
CC
= 5.5 V
V
CC
= 3.0 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
T
A
= +85°C
T
A
= -40°C
Guaranteed
operating window
T
A
= -40°C
T
A
= +25°C
T
A
= -40°C
T
A
= +85°C
T
A
= +25°C
VCC = 2.2 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
TA = -40°C
Guaranteed
operating window
TA = +85°CTA = +25°C
TA = +25°C
TA = -40°C
TA = +85°C
TA = +25°C
Input Frequency, fin (MHz)
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Frequency, fin (MHz)
Input Power, P
IN
(dBm)
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
Input Frequency, fin (MHz)
V
CC
= 5.5 V
+20
+10
0
-10
-20
-30
-40
-50
-60 2000
100
10 1000
T
A
= +85°C
T
A
= -40°C
Guaranteed
operating window
T
A
= +85°C
T
A
= +25°C
T
A
= -40°CT
A
= +25°C
Input Power, P
IN
(dBm)
Input Power, P
IN
(dBm)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Power, P
IN
(dBm)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Frequency, fin (MHz)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
Input Power, P
IN
(dBm)
Divide by 8 mode
(Guaranteed operating window: VCC = 2.2 to 5.5 V, TA = -40 to +85 °C)
.California Eastern Laboratories
UPB1509GV
S11
REF 1.0 Units/
200.0 mUnits/
55.375 -142.79
MARKER 2
700.0 MHZ
2
1
3
2
S11 vs. INPUT FREQUENCY
START 0.050000000 GHz
STOP 1.000000000 GHz
TYPICAL SCATTERING PARAMETERS (TA = 25°C)
S22
REF 1.0 Units
200.0 mUnits/
S22 vs. OUTPUT FREQUENCY
START 0.050000000 GHz
STOP 0.350000000 GHz
Z
50 MHz
149.09 + j 14.86
350 MHz
194.21 j 36.64
FREQUENCY S11
GHz MAG ANG
0.1 0.929 -6.7
0.2 0.898 -10.5
0.3 0.866 -13.6
0.4 0.840 -15.9
0.5 0.834 -19.1
0.6 0.819 -21.9
0.7 0.803 -24.7
0.8 0.792 -27.0
0.9 0.787 -30.0
1.0 0.771 -32.7
VCC1 = VCC2 = 3.0 V, SW1 = SW2 = 3.0 V
.California Eastern Laboratories Wflflfl UUUU California 5mm Lahomloxies, Vow source tor NEG HF, Microwave‘ ome‘eamm m Fmev om Semmaucxm Devmes. A590 mm Henry Dnve . 5m cm CA 9505114817 . we) 91972590 . w (me) mom - www.cel.cnm um sumw m CHANGE waHouT News NEC
UPB1509GV
UPB1509GV
OUTLINE DIMENSIONS (Units in mm)
PACKAGE OUTLINE S08
PIN CONNECTIONS
1. VCC1
2. IN
3. IN
4. GND
5. SW1
6. SW2
7. OUT
8. VCC2
1
2
3
45
7
6
8
876
3.0 MAX
5
1234
N
1509
1.5±0.1
1.8 MAX
0.1 ± 0.1
0.3+0.10
-0.05
0.575 MAX
0.15+0.10
-0.05
4.94 ± 0.2
3.2±0.1
0.87±0.2
0.5 ± 0.2 0.15
0.65
3
+7˚
-3˚
Detail of Lead End
SYSTEM APPLICATION EXAMPLE
RX
TX
SW
PA
VCO
DEMO
N
N
PLL PLL
90¡
0¡
µPB1509GV
¿
I
Q
I
Q
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably
be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify CEL for all damages resulting from such improper use or sale.
ORDERING INFORMATION (Solder Contains Lead)
PART NUMBER QUANTITY
UPB1509GV-E1 1000/Reel
ORDERING INFORMATION (Pb-Free)
PART NUMBER QUANTITY
UPB1509GV-E1-A 1000/Reel
A Business Partner of NEC Compound Semiconductor Devices, Ltd.
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile:
(
408
)
988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix A indicates
that the device is Pb-free. The AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CELs understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS Concentration Limit per RoHS
(values are not yet fixed) Concentration contained
in CEL devices
-A -AZ
Lead (Pb) < 1000 PPM Not Detected (*)
Mercury < 1000 PPM Not Detected
Cadmium < 100 PPM Not Detected
Hexavalent Chromium < 1000 PPM Not Detected
PBB < 1000 PPM Not Detected
PBDE < 1000 PPM Not Detected
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CELs liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.