ZM1.WALL Datasheet by PULS, LP

PULS DIMENSION I E 5 51mm (23‘) III Ill 0 0 III III 0'] HD I 133mm l 143mm I I E E :m Jan. 2015 / Rev. 2.0 DS-ZMI.WALL-EN /AH parameters are Spedfled at 25'C ambient unless otherwrse noted. The intermatron presented in thrs document rs behaved m be atcurate and rehable and may change wrthout nmke. www.pu|spower.mm Phone .49 as 5273 0 Germany
ZM1.WALL
WALL Mounting Bracket
Jan. 2015 / Rev. 2.0 DS-ZM1.WALL-EN / All parameters are specified at 25°C ambient unless otherwise noted.
The information presented in this document is believed to be accurate and reliable and may change without notice.
www.pulspower.com Phone +49 89 9278 0 Germany
1. GENERAL DESCRIPTION
BRACKET FOR WALL MOUNTING
This bracket is used to mount the unit onto a flat
surface without utilizing a DIN-Rail.
The bracket is suitable for all DIMENSION units, which
have the bracket listed as an accessory in the device
datasheets.
2. DIMENSIONS AND INSTALLATION DATA
N L PE
+
+- -
C
B
A
133
143
5.1
INPUT
OUTPUT
A B C
CD5 32mm 4.8mm 22.5mm
CS3 32mm 4.8mm 22.5mm
CS5 32mm 4.8mm 22.5mm
CS10 60mm 5.8mm 48.5mm
CT5 40mm 5.0mm 30.0mm
CT10 62mm 5.7mm 50.6mm
QS3 32mm 4.8mm 22.5mm
QS5 40mm 5.3mm 29.5mm
QS10 60mm 5.8mm 48.5mm
QT20 65mm 6.3mm 40.0mm
QTD20 65mm 6.3mm 40.0mm
QS20 82mm 8.0mm 66.0mm
QS20.244 70mm 8.0mm 54.0mm
UF20 64mm 12.0mm 40.0mm
UB10 49mm 5.3mm 38.4mm
YR2 32mm 4.8mm 22.5mm
YRM2 2mm 4.8mm 22.5mm
Fig. 2-1 Physical dimensions
1/2
PULS DIMENSION Jan. 2015 / Rev. 2.0 DS-ZMI.WALL-EN /AH parameters are Spedfled at 25'C ambient unless otherwrse noted. The intermatron presented in thrs document rs behaved m be atcurate and rehable and may change wrthout nmke. www.pu|spower.mm Phone .49 as 5273 0 Germany
ZM1.WALL
WALL Mounting Bracket
Jan. 2015 / Rev. 2.0 DS-ZM1.WALL-EN / All parameters are specified at 25°C ambient unless otherwise noted.
The information presented in this document is believed to be accurate and reliable and may change without notice.
www.pulspower.com Phone +49 89 9278 0 Germany
3. ASSEMBLY AND MOUNTING INSTRUCTIONS
Fig. 3-1 Detaching DIN-Rail brackets Fig. 3-2 Detach slide Fig. 3-3 Mounting steel bracket
Detach the two aluminium
brackets by removing the four
screws with a Torx screwdriver
(Torx 10).
Remove the plastic lock
mechanism by using a flat-blade
screwdriver to move the lock
downwards while at the same
time push the plastic slider
upwards. Detach the plastic slider.
Mount the steel brackets with the
same screws from the DIN-Rail
brackets. Be careful not to over-
tighten the screws! Recommended
tightening torque is 0.6Nm/
5.3lb.in.
WARNING
Risk of electrical shock, fire,
personal injury or death.
Do not use other screws than the
one from the DIN-Rail bracket.
The unit might become unsafe
when using longer screws as
contact with live electrical circuits
may occur.
4. ORDER NUMBERS
Accessory ZM1.WALL Wall-mounting Bracket Kit (2pcs.)
2/2