LM5050-1(-Q1) Datasheet by Texas Instruments

TEXAS INSTRUMENTS V'.‘ X «4
PS1
PS2
IN GATE OUT
IN GATE OUT
RLOAD
CLOAD
LM5050-1
LM5050-1
GND
GND
VS
VS
VIN VOUT
GND
OFF
OUT
IN GATE
LM5050-1
Shutdown
GND GND
VS
Low= FET On, High= FET Off
100:
0.1 PF
+5.0V to +75V
Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
Reference
Design
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM5050-1
,
LM5050-1-Q1
SNVS629F MAY 2011REVISED DECEMBER 2019
LM5050-1, LM5050-1-Q1 High-Side OR-ing FET Controller
1
1 Features
1 Available in Standard and AEC-Q100 Qualified
Versions LM5050Q0MK-1 (up to 150°C TJ) and
LM5050Q1MK-1 (up to 125°C TJ)
Functional safety capable
Documentation available to aid functional
safety system design
Wide Operating Input Voltage Range, VIN:1Vto
75 V (VBIAS required for VIN < 5 V)
100-V Transient Capability
Charge Pump Gate Driver for External N-Channel
MOSFET
Fast 50-ns Response to Current Reversal
2-A Peak Gate Turnoff Current
Minimum VDS Clamp for Faster Turnoff
Package: SOT-6 (Thin SOT-23-6)
2 Applications
Active OR-ing of Redundant (N+1) Power
Supplies
3 Description
The LM5050-1/-Q1 High Side OR-ing FET Controller
operates in conjunction with an external MOSFET as
an ideal diode rectifier when connected in series with
a power source. This ORing controller allows
MOSFETs to replace diode rectifiers in power
distribution networks thus reducing both power loss
and voltage drops.
The LM5050-1/-Q1 controller provides charge pump
gate drive for an external N-Channel MOSFET and a
fast response comparator to turn off the FET when
current flows in the reverse direction. The LM5050-1/-
Q1 can connect power supplies ranging from 5 V to
75 V and can withstand transients up to 100 V.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
LM5050-1 SOT (6) 2.90 mm × 1.60 mm
LM5050-1-Q1
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Full Application
Typical Redundant Supply Configuration
l TEXAS INSTRUMENTS
2
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description ............................................................. 1
4 Revision History..................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings: LM5050-1 .......................................... 4
6.3 ESD Ratings: LM5050-1-Q1 ..................................... 4
6.4 Recommended Operating Conditions....................... 4
6.5 Thermal Information.................................................. 4
6.6 Electrical Characteristics........................................... 5
6.7 Typical Characteristics.............................................. 8
7 Detailed Description............................................ 11
7.1 Overview ................................................................. 11
7.2 Functional Block Diagram....................................... 12
7.3 Feature Description................................................. 12
7.4 Device Functional Modes........................................ 13
8 Application and Implementation ........................ 14
8.1 Application Information............................................ 14
8.2 Typical Applications ................................................ 16
9 Power Supply Recommendations...................... 21
10 Layout................................................................... 21
10.1 Layout Guidelines ................................................. 21
10.2 Layout Example .................................................... 21
11 Device and Documentation Support ................. 22
11.1 Documentation Support ........................................ 22
11.2 Related Links ........................................................ 22
11.3 Community Resources.......................................... 22
11.4 Trademarks........................................................... 22
11.5 Electrostatic Discharge Caution............................ 22
11.6 Glossary................................................................ 22
12 Mechanical, Packaging, and Orderable
Information ........................................................... 22
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (December 2015) to Revision F Page
Added Functional safety capable link to the Features section............................................................................................... 1
Changes from Revision D (June 2013) to Revision E Page
Added ESD Ratings table, Feature Description section, Device Functional Modes,Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section ................................................................................................. 1
l TEXAS INSTRUMENTS
OFF
GATE
OUT
IN
1
2
3
6
5
4
VS
GND
LM5050MK-1
3
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
5 Pin Configuration and Functions
DDC Package
6-Pin SOT
Top View
Pin Functions
PIN I/O DESCRIPTION
NO. NAME
1 VS I The main supply pin for all internal biasing and an auxiliary supply for the internal gate drive
charge pump. Typically connected to either VOUT or VIN; a separate supply can also be used.
2 GND PWR Ground return for the controller
3 OFF I A logic high state at the OFF pin will pull the GATE pin low and turn off the external MOSFET.
Note that when the MOSFET is off, current will still conduct through the FET's body diode. This
pin should may be left open or connected to GND if unused.
4 IN I Voltage sense connection to the external MOSFET Source pin.
5 GATE O Connect to the Gate of the external MOSFET. Controls the MOSFET to emulate a low forward-
voltage diode.
6 OUT O Voltage sense connection to the external MOSFET Drain pin.
l TEXAS INSTRUMENTS
4
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The GATE pin voltage is typically 12 V above the IN pin voltage when the LM5050-1 is enabled (that is, OFF Pin is Open or Low, and
VIN > VOUT). Therefore, the absolute maximum rating for the IN pin voltage applies only when the LM5050-1 is disabled (that is, OFF
Pin is logic high), or for a momentary surge to that voltage because the Absolute Maximum Rating for the GATE pin is also 100 V
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
IN, OUT Pins to Ground(2) –0.3 100 V
GATE Pin to Ground(2) –0.3 100 V
VS Pin to Ground –0.3 100 V
OFF Pin to Ground –0.3 7 V
Storage Temperature 65 150 °C
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) The MM is a 200-pF capacitor discharged through a 0-Ωresistor (that is, directly) into each pin. Applicable test standard is JESD-A115-
A.
6.2 ESD Ratings: LM5050-1
VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
Machine model (MM)(2) ±150
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
(2) The MM is a 200-pF capacitor discharged through a 0-Ωresistor (that is, directly) into each pin. Applicable test standard is JESD-A115-
A.
6.3 ESD Ratings: LM5050-1-Q1
VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per AEC Q100-002(1) ±2000 V
Machine model (MM)(2) ±150
6.4 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
IN, OUT, VS Pins 5 75 V
OFF Pin 0 5.5 V
Junction Temperature (TJ)
Standard Grade 40 125 °C
LM5050Q0MK-1 40 150 °C
LM5050Q1MK-1 40 125 °C
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Thermal Information
THERMAL METRIC(1)
LM5050-1/-Q1
UNITDDC (SOT)
6 PINS
RθJA Junction-to-ambient thermal resistance 180.7 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 41.3 °C/W
RθJB Junction-to-board thermal resistance 28.2 °C/W
ψJT Junction-to-top characterization parameter 0.7 °C/W
ψJB Junction-to-board characterization parameter 27.8 °C/W
l TEXAS INSTRUMENTS
5
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
Thermal Information (continued)
THERMAL METRIC(1)
LM5050-1/-Q1
UNITDDC (SOT)
6 PINS
RθJC(bot) Junction-to-case (bottom) thermal resistance N/A °C/W
(1) Measurement of VGS voltage (that is. VGATE - VIN) includes 1 Min parallel with CGATE.
6.6 Electrical Characteristics
Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes only. Unless
otherwise stated the following conditions apply: VIN = 12 V, VVS = VIN, VOUT = VIN, VOFF = 0 V, CGATE= 47 nF, and TJ= 25°C.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VS PIN
VVS
Operating
Supply Voltage
Range TJ= –40°C to 125°C 5 75 V
IVS Operating
Supply Current
VVS= 5 V, VIN = 5 V
VOUT = VIN - 100 mV
TJ= 25°C 75
μA
TJ= –40°C to 125°C 105
VVS= 12 V, VIN = 12 V
VOUT = VIN - 100 mV
TJ= 25°C 100
TJ= –40°C to 125°C 147
VVS= 75 V, VIN = 75 V
VOUT = VIN - 100 mV
TJ= 25°C 130
TJ= –40°C to 125°C 288
IN PIN
VIN Operating Input
Voltage Range TJ= –40°C to 125°C 5 75 V
IIN IN Pin current
VIN = 5 V
VVS= VIN
VOUT = VIN - 100 mV
GATE = Open
TJ= 25°C 190
μA
TJ= –40°C to 125°C 32 305
VIN = 12 V to 75 V
VVS= VIN
VOUT = VIN - 100 mV
GATE = Open
TJ= 25°C 320
TJ= –40°C to 125°C LM5050MK-1,
LM5050Q1MK-1 233 400
TJ= –40°C to 125°C LM5050Q0MK-1 233 475
OUT PIN
VOUT
Operating
Output Voltage
Range TJ= –40°C to 125°C 5 75 V
IOUT OUT Pin Current VIN = 5 V to 75 V
VVS= VIN
VOUT = VIN - 100 mV
TJ= 25°C 3.2 µA
TJ= –40°C to 125°C 8
GATE PIN
IGATE(ON) Gate Pin Source
Current
VIN = 5 V
VVS = VIN
VGATE = VIN
VOUT = VIN - 175 mV
TJ= 25°C 30
µA
TJ= –40°C to 125°C 12 41
VIN = 12 V to 75 V
VVS = VIN
VGATE = VIN
VOUT = VIN - 175 mV
TJ= 25°C 32
TJ= –40°C to 125°C 20 41
VGS
VGATE - VIN in
Forward
Operation(1)
VIN = 5 V
VVS = VIN
VOUT = VIN - 175 mV
TJ= 25°C 7
V
TJ= –40°C to 125°C 4 9
VIN = 12 V to 75 V
VVS = VIN
VOUT = VIN - 175 mV
TJ= 25°C 12
TJ= –40°C to 125°C 9 14
l TEXAS INSTRUMENTS
6
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
Electrical Characteristics (continued)
Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes only. Unless
otherwise stated the following conditions apply: VIN = 12 V, VVS = VIN, VOUT = VIN, VOFF = 0 V, CGATE= 47 nF, and TJ= 25°C.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
(2) Time from VIN-VOUT voltage transition from 200 mV to -500 mV until GATE pin voltage falls to VIN + 1 V. See Figure 1.
(3) Time from VOFF voltage transition from 0 V to 5 V until GATE pin voltage falls to VIN + 1 V. See Figure 2
tGATE(REV)
Gate
Capacitance
Discharge Time
at Forward to
Reverse
Transition
See Figure 1
CGATE = 0(2) TJ= 25°C 25
ns
TJ= –40°C to 125°C 85
CGATE = 10 nF(2) TJ= 25°C 60
CGATE = 47 nF(2) TJ= 25°C 180
TJ= –40°C to 125°C 350
tGATE(OFF)
Gate
Capacitance
DischargeTime
at OFF pin Low
to High
Transition
See Figure 2
CGATE = 47 nF(3) TJ= 25°C 486 ns
IGATE(OFF) Gate Pin Sink
Current
VGATE = VIN + 3 V
VOUT > VIN + 100 mV
t10 ms
TJ= 25°C 2.8
ATJ= –40°C to 125°C LM5050MK-1,
LM5050Q1MK-1 1.8
TJ= –40°C to 125°C LM5050Q0MK-1 1.4
VSD(REV)
Reverse VSD
Threshold
VIN < VOUT
VIN - VOUT
TJ= 25°C –28 mV
TJ= –40°C to 125°C –41 –16
ΔVSD(REV) Reverse VSD
Hysteresis TJ= 25°C 10 mV
VSD(REG)
Regulated
Forward VSD
Threshold
VIN > VOUT
VIN = 5 V
VVS = VIN
VIN - VOUT
TJ= 25°C 19
mV
TJ= –40°C to 125°C LM5050MK-1,
LM5050Q1MK-1 1 37
TJ= –40°C to 125°C LM5050Q0MK-1 1 60
TJ= 25°C 22
VIN = 12 V
VVS = VIN
VIN - VOUT
TJ= –40°C to 125°C LM5050MK-1,
LM5050Q1MK-1 4.4 37
TJ= –40°C to 125°C LM5050Q0MK-1 4.4 60
OFF PIN
VOFF(IH)
OFF Input High
Threshold
Voltage
VOUT = VIN-500 mV
VOFF Rising
TJ= 25°C 1.56
V
TJ= –40°C to 125°C 1.75
VOFF(IL)
OFF Input Low
Threshold
Voltage
VOUT = VIN - 500 mV
VOFF Falling
TJ= 25°C 1.4
TJ= –40°C to 125°C 1.1
ΔVOFF
OFF Threshold
Voltage
Hysteresis VOFF(IH) - VOFF(IL) TJ= 25°C 155 mV
IOFF OFF Pin Internal
Pulldown
VOFF = 4.5 V TJ= 25°C 5
µATJ= –40°C to 125°C 3 7
VOFF = 5 V TJ= 25°C 8
{9 TEXAS INSTRUMENTS 200 mV uuv 50v uuv
7
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
Figure 1. Gate OFF Timing for Forward to Reverse Transition
Figure 2. Gate OFF Timing for OFF Pin Low to High Transition
l TEXAS INSTRUMENTS v‘N R.st / v‘N Famng 02465101214 VIMV) VIMV) 5 5 Lmsosm \ \ LMSOSM Vw = Vow Vaur R‘sw Vw = Vom 4 -Vvs : Vow l 4 Vvs : Vum é a f g a '5 vw Falhng '5 5 2 5 2 1 j 1 u u 2 4 a a m 12 «4 «5 an 45 so 75 Vom N) Vom (V) 150 LM5050-1 140 v." , Vvs va = W: 120 me so 'vs M) 60 no 20 u 2 4 6 5101214 Vst 150 Me 120 me 'vs (uA) so so no 20 Vvs (v)
8
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
6.7 Typical Characteristics
Unless otherwise stated: VVS = 12 V, VIN = 12 V, VOFF = 0 V, and TJ= 25°C
Figure 3. IIN vs VIN Figure 4. IIN vs VIN
Figure 5. IOUT vs VOUT Figure 6. IOUT vs VOUT
Figure 7. IVS vs VVS Figure 8. IVS vs VVS
l TEXAS INSTRUMENTS 16 V R 14 w my 12 51““ vw am i >.' 5 >7 >5 5° Vw Vow > Vnsozzm Vvs - Vam u z 4 a s 101214 va) Vw ' Vour > Vosmzm Vvs = Vow u 15 an 45 an 75 WNW) 25 15 14 Vw - Vv: VOU vwm75 mV 1; GATE Open 12 11 10 Van; ' Vw (V) 50 725 u 25 5a 75 100125 TEMPERATURE TJ (no) 'GAI'EAREV) ("57 350 300 S o o o 50 o rsu 725 u 25 so 75 100125 TEMPERATuRE n (no)
-5 0 5 10 15 20 25 30
10
12
14
16
18
20
22
24
26
VOLTS (V)
TIME (5ms / DIV)
Vin
Vout
Vgate
-50 0 50 100 150 200 250
10
12
14
16
18
20
22
24
26
VOLTS (V)
TIME (50ns / DIV)
Vin
Vout
Vgate
9
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise stated: VVS = 12 V, VIN = 12 V, VOFF = 0 V, and TJ= 25°C
Figure 9. (VGATE - VIN) vs VIN, VVS = VOUT Figure 10. (VGATE - VIN) vs VIN, VVS = VOUT
Figure 11. Forward CGATE Charge Time, CGATE = 47 nF Figure 12. Reverse CGATE Discharge, CGATE = 47 nF
Figure 13. VGATE - VIN vs Temperature Figure 14. tGATE(REV) vs Temperature
l TEXAS INSTRUMENTS 19 13 17 16 15 14 13 12 n 10 7w 725 u 25 5a 75 100125 TEMPERATURE n m Vow M Vorru ‘m (an) Varm Von THRESHOLDS (V) 25 Canaan; g 20 § Vans 0 > 15 / Com 0 _ ,— a1: SUM40N15738 m S 5 vwrvoupasomv 1 W 210;; o > o w w 1 msIDIV t us! mv 15 3 z m ? 5 5 vm=12v > 0 u1=suM40N15-aa ILOAD A Com 0 m m : SUIMUN15—38 15a Vw‘Vour WV) a 1 z 3 4 5 1 us] DIV LOAD CURREN'I (A)
10
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
Typical Characteristics (continued)
Unless otherwise stated: VVS = 12 V, VIN = 12 V, VOFF = 0 V, and TJ= 25°C
Figure 15. OFF Pin Thresholds vs Temperature Figure 16. OFF Pin Pulldown vs Temperature
Figure 17. CGATE Charge and Discharge vs OFF Pin Figure 18. OFF Pin, ON to OFF Transition
Figure 19. OFF Pin, OFF to ON Transition Figure 20. GATE Pin vs (RDS(ON) × IDS)
l TEXAS INSTRUMENTS
11
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
7 Detailed Description
7.1 Overview
Blocking diodes are commonly placed in series with supply inputs for the purpose of ORing redundant power
sources and protecting against supply reversal. The LM5050 replaces diodes in these applications with an N-
MOSFET to reduce both the voltage drop and power loss associated with a passive solution. At low input
voltages, the improvement in forward voltage loss is readily appreciated where headroom is tight, as shown in
Figure 2. The LM5050 operates from 5 V to 75 V and it can withstand an absolute maximum of 100 V without
damage. A 12-V or 15-A ideal diode application is shown in Figure 24. Several external components are included
in addition to the MOSFET, Q1. Ideal diodes, like their non-ideal counterparts, exhibit a behavior known as
reverse recovery. In combination with parasitic or intentionally introduced inductances, reverse recovery spikes
may be generated by an ideal diode during an reverse current shutdown. D1, D2 and R1 protect against these
spikes which might otherwise exceed the LM5050 100-V survival rating. COUT also plays a role in absorbing
reverse recovery energy. Spikes and protection schemes are discussed in detail in the Short Circuit Failure of an
Input Supply section.
NOTE
The OFF pin may be used to active the GATE pull down circuit and turn off the pass
MOSFET, but it does not disconnect the load from the input because Q1’s body diode is
still present.
If Vs is powered while IN is floating or grounded, then about 0.5mA will leak from the Vs
pin into the IC and about 3mA will leak from the OUT pin into the IC. From this leakage,
about 50 uA will flow out of the IN pin and the rest will flow to ground. This does not affect
long term reliability of the IC, but may influence circuit design. See Reverse Input Voltage
Protection With IQ Reduction for details on how to avoid this leakage current.
Kw} in
IN OUTGATE
1.5V
OFF
VS
GND
LM5050- 1
Reverse
Comparator
LOAD
INPUT
35 µA
14V
30 mV
30 µA
30 mV
5 µA
- +
-+
Bias
Circuitry
-+
2A
MOSFET Off
+12V Charge
Pump
12
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 IN, GATE, and OUT Pins
When power is initially applied, the load current will flow from source to drain through the body diode of the
MOSFET. Once the voltage across the body diode exceeds VSD(REG) then the LM5050-1 begins charging the
MOSFET gate through a 32 µA (typical) charge pump current source . In forward operation, the gate of the
MOSFET is charged until it reaches the clamping voltage of the 12-V GATE to IN pin Zener diode internal to the
LM5050-1.
The LM5050-1 is designed to regulate the MOSFET gate-to-source voltage. If the MOSFET current decreases to
the point that the voltage across the MOSFET falls below the VSD(REG) voltage regulation point of 22 mV (typical),
the GATE pin voltage will be decreased until the voltage across the MOSFET is regulated at 22 mV. If the
source-to-drain voltage is greater than the VSD(REG) voltage, the gate-to-source voltage will increase and
eventually reach the 12-V GATE to IN pin Zener clamp level.
l TEXAS INSTRUMENTS
13
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
Feature Description (continued)
If the MOSFET current reverses, possibly due to failure of the input supply, such that the voltage across the
LM5050-1 IN and OUT pins is more negative than the VSD(REV) voltage of -28 mV (typical), the LM5050-1 will
quickly discharge the MOSFET gate through a strong GATE to IN pin discharge transistor.
If the input supply fails abruptly, as would occur if the supply was shorted directly to ground, a reverse current
will temporarily flow through the MOSFET until the gate can be fully discharged. This reverse current is sourced
from the load capacitance and from the parallel connected supplies. The LM5050-1 responds to a voltage
reversal condition typically within 25 ns. The actual time required to turn off the MOSFET will depend on the
charge held by the gate capacitance of the MOSFET being used. A MOSFET with 47 nF of effective gate
capacitance can be turned off in typically 180 ns. This fast turnoff time minimizes voltage disturbances at the
output, as well as the current transients from the redundant supplies.
7.3.2 VS Pin
The LM5050-1 VS pin is the main supply pin for all internal biasing and an auxiliary supply for the internal gate
drive charge pump.
For typical LM5050-1 applications, where the input voltage is above 5 V, the VS pin can be connected directly to
the OUT pin. In situations where the input voltage is close to, but not less than, the 5 V minimum, it may be
helpful to connect the VS pin to the OUT pin through an RC Low-Pass filter to reduce the possibility of erratic
behavior due to spurious voltage spikes that may appear on the OUT and IN pins. The series resistor value
should be low enough to keep the VS voltage drop at a minimum. A typical series resistor value is 100 . The
capacitor value should be the lowest value that produces acceptable filtering of the voltage noise.
If Vs is powered while IN is floating or grounded, then about 0.5 mA will leak from the Vs pin into the IC and
about 3mA will leak from the OUT pin into the IC. From this leakage, about 50 uA will flow out of the IN pin and
the rest will flow to ground. This does not affect long term reliability of the IC, but may influence circuit design.
See Reverse Input Voltage Protection With IQ Reduction for details on how to avoid this leakage current.
Alternately, it is possible to operate the LM5050-1 with VIN value as low as 1 V if the VS pin is powered from a
separate supply. This separate VS supply must be from 5 V and 75 V. See Figure 27.
7.3.3 OFF Pin
The OFF pin is a logic level input pin that is used to control the gate drive to the external MOSFET. The
maximum operating voltage on this pin is 5.5 V.
When the OFF pin is high, the MOSFET is turned off (independent of the sensed IN and OUT voltages). In this
mode, load current will flow through the body diode of the MOSFET. The voltage difference between the IN pin
and OUT pins will be approximately 700 mV if the MOSFET is operating normally through the body diode.
The OFF pin has an internal pulldown of 5 µA (typical). If the OFF function is not required the pin may be left
open or connected to ground.
7.4 Device Functional Modes
7.4.1 ON/OFF Control Mode
The MOSFET can be turned off by asserting the OFF pin high. This mode only disables the MOSFET, but VOUT
is still available through the body diode of the MOSFET.
7.4.2 External Power Supply Mode
The Vs pin of the LM5050 can be operated from 5 V to 75 V as the bias input supply. In this mode VIN voltage
can be as low as 1 V, as shown in Figure 27.
! TEXAS INSTRUMENTS ..»—I -.I-' II-
PS1
PS2
IN GATE OUT
IN GATE OUT
RLOAD
CLOAD
LM5050-1
LM5050-1
GND
GND
VS
VS
PS1
PS2
RLOAD
CLOAD
14
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
Systems that require high availability often use multiple, parallel-connected redundant power supplies to improve
reliability. Schottky OR-ing diodes are typically used to connect these redundant power supplies to a common
point at the load. The disadvantage of using OR-ing diodes is the forward voltage drop, which reduces the
available voltage and the associated power losses as load currents increase. Using an N-channel MOSFET to
replace the OR-ing diode requires a small increase in the level of complexity, but reduces, or eliminates, the
need for diode heat sinks or large thermal copper area in circuit board layouts for high power applications.
Figure 21. OR-ing with Diodes
The LM5050-1/-Q1 is a positive voltage (that is, high-side) OR-ing controller that will drive an external N-channel
MOSFET to replace an OR-ing diode. The voltage across the MOSFET source and drain pins is monitored by
the LM5050-1 at the IN and OUT pins, while the GATE pin drives the MOSFET to control its operation based on
the monitored source-drain voltage. The resulting behavior is that of an ideal rectifier with source and drain pins
of the MOSFET acting as the anode and cathode pins of a diode respectively.
Figure 22. OR-ing With MOSFETs
l TEXAS INSTRUMENTS
15
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
Application Information (continued)
8.1.1 MOSFET Selection
The important MOSFET electrical parameters are the maximum continuous Drain current ID, the maximum
Source current (that is, body diode) IS, the maximum drain-to-source voltage VDS(MAX), the gate-to-source
threshold voltage VGS(TH), the drain-to-source reverse breakdown voltage V(BR)DSS, and the drain-to-source On
resistance RDS(ON).
The maximum continuous drain current, ID, rating must exceed the maximum continuous load current. The rating
for the maximum current through the body diode, IS, is typically rated the same as, or slightly higher than the
drain current, but body diode current only flows while the MOSFET gate is being charged to VGS(TH).
Gate Charge Time = Qg/ IGATE(ON)
1. The maximum drain-to-source voltage, VDS(MAX), must be high enough to withstand the highest differential
voltage seen in the application. This would include any anticipated fault conditions.
2. The drain-to-source reverse breakdown voltage, V(BR)DSS, may provide some transient protection to the OUT
pin in low voltage applications by allowing conduction back to the IN pin during positive transients at the OUT
pin.
3. The gate-to-source threshold voltage, VGS(TH), should be compatible with the LM5050-1 gate drive
capabilities. Logic level MOSFETs, with RDS(ON) rated at VGS(TH) at 5 V, are recommended, but sub-Logic
level MOSFETs having RDS(ON) rated at VGS(TH) at 2.5 V, can also be used.
4. The dominate MOSFET loss for the LM5050-1 active OR-ing controller is conduction loss due to source-to-
drain current to the output load, and the RDS(ON) of the MOSFET. This conduction loss could be reduced by
using a MOSFET with the lowest possible RDS(ON). However, contrary to popular belief, arbitrarily selecting a
MOSFET based solely on having low RDS(ON) may not always give desirable results for several reasons:
1. Reverse transition detection. Higher RDS(ON) will provide increased voltage information to the LM5050-1
Reverse Comparator at a lower reverse current level. This will give an earlier MOSFET turnoff condition
should the input voltage become shorted to ground. This will minimize any disturbance of the redundant
bus.
2. Reverse current leakage. In cases where multiple input supplies are closely matched it may be possible
for some small current to flow continuously through the MOSFET drain to source (that is, reverse)
without activating the LM5050-1 Reverse Comparator. Higher RDS(ON) will reduce this reverse current
level.
3. Cost. Generally, as the RDS(ON) rating goes lower, the cost of the MOSFET goes higher.
5. The dominate MOSFET loss for the LM5050-1 active OR-ing controller is conduction loss due to source-to-
drain current to the output load, and the RDS(ON) of the MOSFET. This conduction loss could be reduced by
using a MOSFET with the lowest possible RDS(ON). However, contrary to popular belief, arbitrarily selecting a
MOSFET based solely on having low RDS(ON) may not always give desirable results for several reasons:
a. Selecting a MOSFET with an RDS(ON) that is too large will result in excessive power dissipation.
Additionally, the MOSFET gate will be charged to the full value that the LM5050-1 can provide as it
attempts to drive the Drain to Source voltage down to the VSD(REG) of 22 mV typical. This increased Gate
charge will require some finite amount of additional discharge time when the MOSFET needs to be
turned off.
b. As a guideline, it is suggest that RDS(ON) be selected to provide at least 22 mV, and no more than 100
mV, at the nominal load current.
c. (22 mV / ID)RDS(ON) (100 mV / ID)
d. The thermal resistance of the MOSFET package should also be considered against the anticipated
dissipation in the MOSFET to ensure that the junction temperature (TJ) is reasonably well controlled,
because the RDS(ON) of the MOSFET increases as the junction temperature increases.
6. PDISS = ID2× (RDS(ON))
7. Operating with a maximum ambient temperature (TA(MAX)) of 35°C, a load current of 10 A, and an RDS(ON) of
10 m, and desiring to keep the junction temperature under 100°C, the maximum junction-to-ambient
thermal resistance rating (θJA) must be:
a. RθJA (TJ(MAX) - TA(MAX))/(ID2× RDS(ON))
b. RθJA (100°C - 35°C)/(10 A × 10 A × 0.01 )
VIN
48V VOUT
GND
OFF
OUT
IN GATE
LM5050-1
OFF/ON
GND GND
Q1
SUM40N10-30
+
R1
100:
CIN
1 PF
75V
D1
SS16T3
COUT
22 PF
63V
D2
SMBJ60A
VS
C1
0.1 PF
100V
S D
G
IN GATE OUT
CLOAD
LM5050-1
GND
COUT
Parasitic
Inductance
Parasitic
Inductance
Shorted
Input
Reverse Recovery Current
VS
16
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
Application Information (continued)
c. RθJA 65°C/W
8.1.2 Short Circuit Failure of an Input Supply
An abrupt 0-Ωshort circuit across the input supply will cause the highest possible reverse current to flow while
the internal LM5050-1 control circuitry discharges the gate of the MOSFET. During this time, the reverse current
is limited only by the RDS(ON) of the MOSFET, along with parasitic wiring resistances and inductances. Worst
case instantaneous reverse current would be limited to:
ID(REV) = (VOUT - VIN) / RDS(ON) (1)
The internal Reverse Comparator will react, and will start the process of discharging the Gate, when the reverse
current reaches:
ID(REV) = VSD(REV) / RDS(ON) (2)
When the MOSFET is finally switched off, the energy stored in the parasitic wiring inductances will be transferred
to the rest of the circuit. As a result, the LM5050-1 IN pin will see a negative voltage spike while the OUT pin will
see a positive voltage spike. The IN pin can be protected by diode clamping the pin to GND in the negative
direction. The OUT pin can be protected with a TVS protection diode, a local bypass capacitor, or both. In low
voltage applications, the MOSFET drainto- source breakdown voltage rating may be adequate to protect the
OUT pin (that is, VIN + V(BR)DSS(MAX) < 75 V ), but most MOSFET data sheets do not ensure the maximum
breakdown rating, so this method should be used with caution.
Figure 23. Reverse Recovery Current Generates Inductive Spikes at VIN and VOUT pins.
8.2 Typical Applications
8.2.1 Typical Application With Input and Output Transient Protection
Figure 24. Typical Application With Input and Output Transient Protection Schematic
l TEXAS INSTRUMENTS Teksmv 4'; Nnnmmm Teksmv 4'; Nnnmmm , , , @va .vwrwm.._____/ .Snnmv ouswv .5»an ouswv n mnv mm: 4an 5mm n mnv mm: 4an Hum
17
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
Typical Applications (continued)
8.2.1.1 Design Requirements
Table 1 shows the parameters for Figure 24
Table 1. Design Parameters
DESIGN PARAMETER EXAMPLE VALUE
Minimum Input Voltage, VINMIN 6 V
Maximum Input Voltage, VINMax 50 V
Output Current Range, IOUT 0 to 15 A
Ambient Temperature Range, TA0°C to 50°C
8.2.1.2 Detailed Design Procedure
The following design procedure can be used to select component values for the LM5050-1.
8.2.1.2.1 Power Supply Components (R1 C1,) Selection
The LM5050-1 VS pin is the main supply pin for all internal biasing and an auxiliary supply for the internal gate
drive charge pump. The series resistor (R1) value should be low enough to keep the VS voltage drop at a
minimum. A typical series resistor value is 100 . The capacitor value (0.1 uF typical) should be the lowest value
that produces acceptable filtering of the voltage noise.
8.2.1.2.2 MOSFET (Q1) Selection
The MOSFET (Q1) selection procedure is explained in detail in MOSFET Selection. The MOSFET used in the
design example is SUM40N10-30-E3.
8.2.1.2.3 D1 and D2 Selection for Inductive Kick-Back Protection
Diode D1 and capacitor C1 and diode D2 and capacitor C2 in the Figure 27 serve as inductive kick-back
protection to limit negative transient voltage spikes generated on the input when the input supply voltage is
abruptly shorted to zero volts. As a result, the LM5050-1 IN pin will see a negative voltage spike while the OUT
pin will see a positive voltage spike. The IN pin can be protected by schottky diode (D1) clamping the pin to GND
in the negative direction, similarly the OUT pin should be protected with a TVS protection diode (D1), or with a
local bypass capacitor, or both. D1 is selected as 1-A, 60-V Schottky Barrier Rectifier (SS16T3G) and D2 is the
60 V, TVS (SMBJ60A-13-F).
8.2.1.3 Application Curves
Figure 25. Forward voltage (VIN-VOUT) Drop Reduces
When Gate is Enabled (VIN = 12 V) Figure 26. Forward Voltage (VIN-VOUT) Drop Increases
When Gate is Disabled (VIN = 12 V)
PS1
PS2
IN GATE OUT
IN GATE OUT
RLOAD
CLOAD
LM5050-1
LM5050-1
GND
GND
COUT
VS
VS
VIN
1V to 75V VOUT
GND
OFF
OUT
IN GATE
LM5050-1
Off/On
GND GND
VBIAS
5.0V to 75V
Q1
+
C1
1.0 PF
100V
D1
C2
22 PF
100V
D2
TVS
82V
VS
GND
R1
100
C3
0.1 PF
100V
18
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
8.2.2 Using a Separate VS Supply for Low Vin Operation
In some applications, it is desired to operate LM5050-1 from low supply voltage. The LM5050-1 can operate with
a 1-V rail voltage, provided its VS pin is biased from 5 V to 75 V. The detail of such application is depicted in
Figure 27.
Figure 27. Using a Separate vs Supply for Low Vin Operation Schematic
8.2.3 ORing of Two Power Sources
Figure 28. ORing of Two Power Sources
‘5‘ TEXAS INSTRUMENTS O—I
VIN
5.0V to 75V
VOUT
GND
OFF
OUT
IN GATE
LM5050-1
OFF/ON
GND GND
Q1
SUM40N10-30
CIN
1 PF
100V
D1
B180-13-F
VS
S D
G
ON/OFF
Control
Q1
VOUT
GND
CIN Cout
D1
D2
D3
D4
C1
R1
VIN
GND
Q2
100»
0.1µF
100V
LM5050-1
IN GATE OUT
VS
GND SMBJ60A
22uF
63V
1uF
75V
SS16T3
BAS40-7-F
SS16T3
NTR5198NLT3G
SUM40N10-30
48V
19
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
8.2.4 Reverse Input Voltage Protection With IQ Reduction
If Vs is powered while IN is floating or grounded, then about 0.5 mA will leak from the Vs pin into the IC and
about 3 mA will leak from the OUT pin into the IC. From this leakage, about 50 uA will flow out of the IN pin and
the rest will flow to ground. This does not affect long term reliability of the IC, but may influence circuit design.
In battery powered applications, whenever LM5050-1 functionality is not needed, the supply to the LM5050-1 can
be disconnected by turning “OFF” Q2, as shown in Figure 29. This disconnects the ground path of the LM5050-1
and eliminates the current leakage from the battery.
The quiescent current of LM5050-1 can be also reduced by disconnecting the supply to VS pin, whenever
LM5050-1 function is not need.
Figure 29. Reverse Input Voltage Protection With IQ Reduction Schematic
8.2.5 Basic Application With Input Transient Protection
Figure 30. Basic Application With Input Transient Protection Schematic
l TEXAS INSTRUMENTS n zunv 2m 0 154w um m cm um m cm n zunv mm flflmx qualms. \rww «an mam
VIN
48V VOUT
GND
OFF
OUT
IN GATE
LM5050-1
GND GND
Q1
SUM40N10-30
+
R1
100:
CIN
1 PF
75V
D1
SS16T3
COUT
22 PF
63V
D2
SMBJ60A
VS
C1
0.1 PF
100V
S D
G
D3
SS16T3
20
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
8.2.6 48-V Application With Reverse Input Voltage (VIN = –48 V) Protection
Figure 31. 48-V Application With Reverse Input Voltage (VIN = –48 V) Protection Schematic
8.2.6.1 Application Curves
Figure 32. Operation With Positive Polarity Input With
(VIN = 25 V) Figure 33. Operation With Negative polarity Input With
(VIN = –25 V)
I TEXAS INSTRUMENTS
VOUT
LM5050-1
D
GS
Gate
IN
OUT
OFF
VS
GND
VIN
C1
R1
GND
D1
D4
COUT
CIN
21
LM5050-1
,
LM5050-1-Q1
www.ti.com
SNVS629F MAY 2011REVISED DECEMBER 2019
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation FeedbackCopyright © 2011–2019, Texas Instruments Incorporated
9 Power Supply Recommendations
When the LM5050-1/-Q1 shuts off the external MOSFET, transient voltages will appear on the input and output
due to reverse recovery, as discussed in Short Circuit Failure of an Input Supply.To prevent LM5050-1 and
surrounding components from damage under the conditions of a direct input short circuit, it is necessary to clamp
the negative transient at IN, and OUT pins with TVS.
10 Layout
10.1 Layout Guidelines
The typical PCB layout for LM5050-1/-Q1 is shown in Figure 34. TI recommends connecting the IN, Gate and
OUT pins close to the source and drain pins of the MOSFET. Keep the traces of the MOSFET drain wide and
short to minimize resistive losses. Place surge suppressors (D1 and D4) components as shown in the example
layout of LM5050-1 in Layout Example.
10.2 Layout Example
Figure 34. Typical Layout Example With D2PAK N-MOSFET
l TEXAS INSTRUMENTS
22
LM5050-1
,
LM5050-1-Q1
SNVS629F –MAY 2011REVISED DECEMBER 2019
www.ti.com
Product Folder Links: LM5050-1 LM5050-1-Q1
Submit Documentation Feedback Copyright © 2011–2019, Texas Instruments Incorporated
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
Achieving Stable VGS Using LM5050-1 with Low Current and Noisy Input Supply, SLVA684
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 2. Related Links
PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL
DOCUMENTS TOOLS &
SOFTWARE SUPPORT &
COMMUNITY
LM5050-1 Click here Click here Click here Click here Click here
LM5050-1-Q1 Click here Click here Click here Click here Click here
11.3 Community Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
I TEXAS INSTRUMENTS Samples Samples Sample: Sample: Samples Samples
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM5050MK-1/NOPB ACTIVE SOT-23-THIN DDC 6 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 SZHB
LM5050MKX-1/NOPB ACTIVE SOT-23-THIN DDC 6 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 SZHB
LM5050Q0MK-1/NOPB ACTIVE SOT-23-THIN DDC 6 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 150 SL5B
LM5050Q0MKX-1/NOPB ACTIVE SOT-23-THIN DDC 6 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 150 SL5B
LM5050Q1MK-1/NOPB ACTIVE SOT-23-THIN DDC 6 1000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 SP3B
LM5050Q1MKX-1/NOPB ACTIVE SOT-23-THIN DDC 6 3000 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 SP3B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
I TEXAS INSTRUMENTS
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM5050-1, LM5050-1-Q1 :
Catalog: LM5050-1
Automotive: LM5050-1-Q1
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
I TEXAS INSTRUMENTS 5:. V.’
PACKAGE MATERIALS INFORMATION
www.ti.com 9-Aug-2022
TAPE AND REEL INFORMATION
Reel Width (W1)
REEL DIMENSIONS
A0
B0
K0
W
Dimension designed to accommodate the component length
Dimension designed to accommodate the component thickness
Overall width of the carrier tape
Pitch between successive cavity centers
Dimension designed to accommodate the component width
TAPE DIMENSIONS
K0 P1
B0 W
A0
Cavity
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Pocket Quadrants
Sprocket Holes
Q1 Q1Q2 Q2
Q3 Q3Q4 Q4 User Direction of Feed
P1
Reel
Diameter
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM5050MK-1/NOPB SOT-23-
THIN DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM5050MKX-1/NOPB SOT-23-
THIN DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM5050Q0MK-1/NOPB SOT-23-
THIN DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM5050Q0MKX-1/NOPB SOT-23-
THIN DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM5050Q1MK-1/NOPB SOT-23-
THIN DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM5050Q1MKX-1/NOPB SOT-23-
THIN DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
W
L
H
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM5050MK-1/NOPB SOT-23-THIN DDC 6 1000 208.0 191.0 35.0
LM5050MKX-1/NOPB SOT-23-THIN DDC 6 3000 208.0 191.0 35.0
LM5050Q0MK-1/NOPB SOT-23-THIN DDC 6 1000 208.0 191.0 35.0
LM5050Q0MKX-1/NOPB SOT-23-THIN DDC 6 3000 208.0 191.0 35.0
LM5050Q1MK-1/NOPB SOT-23-THIN DDC 6 1000 208.0 191.0 35.0
LM5050Q1MKX-1/NOPB SOT-23-THIN DDC 6 3000 208.0 191.0 35.0
Pack Materials-Page 2
I-III
www.ti.com
PACKAGE OUTLINE
C
0.20
0.12 TYP 0.25
3.05
2.55
4X 0.95
1.1
0.7
0.1
0.0 TYP
6X 0.5
0.3
0.6
0.3 TYP
1.9
0 -8 TYP
A
3.05
2.75
B
1.75
1.45
SOT-23 - 1.1 max heightDDC0006A
SMALL OUTLINE TRANSISTOR
4214841/C 04/2022
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC MO-193.
34
0.2 C A B
16
INDEX AREA
PIN 1
GAGE PLANE
SEATING PLANE
0.1 C
SCALE 4.000
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MAX
ARROUND 0.07 MIN
ARROUND
6X (1.1)
6X (0.6)
(2.7)
4X (0.95)
(R0.05) TYP
4214841/C 04/2022
SOT-23 - 1.1 max heightDDC0006A
SMALL OUTLINE TRANSISTOR
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
SYMM
LAND PATTERN EXAMPLE
EXPLOSED METAL SHOWN
SCALE:15X
SYMM
1
34
6
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
EXPOSED METAL
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDERMASK DETAILS
EXPOSED METAL
www.ti.com
EXAMPLE STENCIL DESIGN
(2.7)
4X(0.95)
6X (1.1)
6X (0.6)
(R0.05) TYP
SOT-23 - 1.1 max heightDDC0006A
SMALL OUTLINE TRANSISTOR
4214841/C 04/2022
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:15X
SYMM
SYMM
1
34
6
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated