DSTOPK Installation Datasheet by Hammond Manufacturing

INSTALLATION OF DOOR WIND STOP KIT ON A ECLIPSE SERIES WALLMOUNT NOTE: E3
BUL10277
DSTOPK
REV. D
HAMMOND
MANUFACTURING
S
TOOL BOX
Tape
Measure
PAGE 1 OF 2
INSTALLATION OF DOOR WIND STOP KIT
ON A ECLIPSE SERIES WALLMOUNT
Drill, use
(0.218 in)
3/8" Socket
Wrench
1/8 ALLEN
KEY
NOTE:
MINIMUM WIDTH UNIT THAT WIND STOP CAN BE
MOUNTED ON IS 20" WIDE UNIT (DIM "B" IN CATALOGUE)
K
BOTTOM
INSTALLATION 3 3/8
TOP
INSTALLATION 3 1/32
INSERT SEALING WASHER OUTSIDE
OF ENCLOSURE WITH RUBBER
SIDE FACING ENCLOSURE
(APPLY TO 5 DRILLED HOLES)
BRACKET
DRILL 3 X
O
.218
THRU HOLE
FRONT VIEW OF DOOR
HINGE SIDE
SEALING WASHER
ISOMETRIC VIEW
BOTTOM INSTALLATION
DRILL 2 X
O
.218
THRU HOLE
ISOMETRIC VIEW
FRONT VIEW OF BODY
HINGE SIDE
INSTALLATION INSTRUCTIONS:
(1) From views and chart select the application best suited for your installation.
(2) Using the "X" and "Y" dimensions plus the bottom or top installation views drill 0.218 diameter hole to suit the installation.
(3) Install bracket that comes in kit to top or bottom of enclosure lip and install the angle bracket of wind stop to door with 10-32 hardware and sealing washer supplied.
NOTE: Position of bracket on door with your application.
(4) Install bar bracket per application selected paying attention to pin orientation.
1 1/2
1 1/2
3 5/8 3 5/8 3 5/8
3 5/8
OPENING ANGLE X Y
90 3 3/16 8
105 3 3/16 7 1/4
120 3 3/16 6 5/8
135 3 6 3/8
7/16
7/16
ISOMETRIC VIEW
TOP INSTALLATION
INSTALLATION OF DOOR WIND STOP KIT ON HW 1418 &1422 SERIES WALLMOUNT AND FREE STANDING Nm‘E: INSTALLATION INSTRUCTIONS: NOTE:
DSTOPK
TOOL BOX
Tape
Measure
PAGE 2 OF 2
INSTALLATION OF DOOR WIND STOP KIT ON HW,
1418 &1422 SERIES WALLMOUNT AND FREE
STANDING
Drill, use
(0.218 in)
3/8" Socket
Wrench
1/8 ALLEN
KEY
BUL10277
REV. D
HAMMOND
MANUFACTURING
S
NOTE:
MINIMUM WIDTH UNIT THAT WIND STOP CAN BE
MOUNTED ON IS 20" WIDE UNIT (DIM "B" IN CATALOGUE)
OPENING ANGLE X Y
90 4 7 7/16
105 4 6 1/2
120 4 5 13/16
135 3 3/4 5 1/4
INSERT SEALING WASHER OUTSIDE
OF ENCLOSURE WITH RUBBER
SIDE FACING ENCLOSURE
(APPLY TO 5 DRILLED HOLES)
K
BOTTOM
INSTALLATION 2 9/16
TOP
INSTALLATION 2 1/4
FRONT VIEW OF BODY
ISOMETRIC VIEW
FRONT VIEW OF DOOR
DRILL 3 X
O
.218
THRU HOLE
HINGE SIDE
BRACKET
SEALING WASHER
HINGE SIDE
DRILL 2 X
O
.218
THRU HOLE
INSTALLATION INSTRUCTIONS:
(1) From views and chart select the application best suited for your installation.
(2) Using the "X" and "Y" dimensions plus the bottom or top installation views drill 0.218 diameter hole to suit the installation.
(3) Install bracket that comes in kit to top or bottom of enclosure lip and install the angle bracket of wind stop to door with 10-32 hardware and sealing washer supplied.
NOTE: Position of bracket on door with your application.
(4) Install bar bracket per application selected paying attention to pin orientation.
3 5/8
3 5/8
1 1/2
1 1/2
ISOMETRIC VIEW
BOTTOM INSTALLATION
3 5/8
3 5/8
13/16
13/16
ISOMETRIC VIEW
TOP INSTALLATION