AA3528P3S Datasheet by Kingbright

Kl'ngbrl'ghI 3.5[0.138]i0.2 ‘ 3.2[o.1ze]1o.2 \ 28[D11]:l:02 N r—v—’—v—\ 4L //+\\ \ \\ 4434+; \ \ \ / \\ + / z T Q_._‘4 ‘ 2 2[0 057] ‘ ¢2,4[o.094] , fl , \ COLLECTOR 0' i a: o D. E. “f ':' o m N no ‘ . o M g a o s H «H ‘ ‘ 7 sq '5‘ fl \ [—J ,‘ o l\ g :1,::, 2 6L 44.1:J 3‘ 3W \ o.s[o.os1]to.3 '
SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 1 OF 6
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871
Part Number: AA3528P3S
zMechanically and spectrally matched to the infrared emitting
LED lamp.
zPackage : 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Made with NPN silicon phototransistor chips.
Package Dimensions
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 2 OF 6
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
Kl'ngbrl'ghI mea‘ [Wacvroiopilcul churamermms Curves CnHaclnr iner nimpaunn Fd(mW) rvw Comm PowerDlulpaHen u. ‘25 mo 75 50 25 n Amb'mm Ttmp-rulurl T 725 u 25 so 7555‘00 Ambvem tempermum ncc) Ra‘aflva Spamm SansIIMIy “9.2 smml 5“:va v- an unulh “1:251: ova 0.5 0.4 oz o 350 550 750 nm n50 wuvslsngm A (mu)
SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 3 OF 6
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871
Electrical / Optical Characteristics at TA=25°C
Absolute Maximum Ratings at TA=25°C
Symbol Parameter Min. Typ. Max. Units Test Conditions
VBR CEO Collector-to-Emitter Breakdown Voltage 30 V IC=100uA
VBR ECO Emitter-to-Collector Breakdown Voltage 5 V IE=100uA
VCE (SAT) Collector-to-Emitter Saturation Voltage 0.8 V IC=2mA
I CEO Collector Dark Current 100 nA VCE=10V
TR Rise Time (10to 90% ) 15 us
VCE = 5V
TF Fall Time (90to 10% ) 15 us
I (ON) On State Collector Current 0.2 0.4 mA
VCE = 5V
λ0.1 Range of spectral bandwidth 420 1120 nm
λp Wavelength of peak sensitivity 940 nm
2θ1/2 Angle of half sensitivity 120 deg
Parameter Max.Ratings
Collector-to-Emitter Voltage 30V
Emitter-to-Collector Voltage 5V
Power Dissipation at (or below) 25°C Free Air Temperature 100mW
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
1. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
Kl'ngbrlghl F‘gl Remnve Conway Curr-n0 Ammem Tumpamluru N o Relaliva comm CurmnlO‘) o u m 10 3a 40 so so mm“. Timparulurl use) figs Con-cm Dark Cummr vs- Amblum Tum-rum- m’ vpm ‘ u" Cn‘lacmr om eumm (mA) m" 25 a so 75 Amblem Temperalun “(-0) run Rsipnn" Hm vs Loud Rulslunce H30 v§=5v GT \: GDuA 3 Iu:25‘c E In g ‘ x” m cm n.‘ Loud Rts'wsiuncl Nun) my leumor oumm (E:).Vce=§V. rq=25'c m mA lo 10' m" m" 70 d '0‘ o1 la" ‘ m‘ mw/cmz # z. r .s Can-amourrm vs. CoHecmr—[mmzr anmgu 2.5 z.n 1.5 r.» ”nu/Mt La ’2 5 E a naum/umx 0.5 4 Inn on ‘ z 3 Co‘lsclokEmMu Vouage vcav) 5 my Circuit m Rasponsa mm. mm Va: \npulj? 0-.qu \ M IU 0mm 71‘ ’ J:
SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 4 OF 6
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871
Kl'ngbrl'ghI Reflow So‘derlfla Prom: For Lead—me SMT Process. ('c7 mum" 2m. "Eli m A'C/I mm w “K ‘ c/smnx E m Emu. mu. 2 5., a a 5., m Em) mm mm LWa rlzummlnd in. mm sempmmm 245%: +/—5'r:)1h muxfmum :o‘den'rw mmpemm mm be n m m m 0. 2mm nuns: sires: a "la Ipnxy ras'm while u is ”new In high umpemmm. 5.Numbar m mmw prams: man be 2 “me: or less. :3 in ml «5 islu 55m 2 ‘ 2.2 nun mam 4.1“, W m! 1: no new 2 Tape 0' +\ In ". N é Q a m / g m \ m 5Typ L—J 3 1:0 1 A—A Secuon
SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 5 OF 6
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Tape Specifications
(Units : mm)
Reel Dimension
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Kl'ngbrl'ghI ZWBIReeI 1 Reel , 3., King right 401(1st mKlSMan I I \ KI n g b H g h t FINQ MSW aw: mm m: at; u " SIN: xxxx ‘ MAW ODDE: XXX LOW MO: [IMMMIMJMIHI‘IIHII‘I‘\|||H|\||H||||H\|||\IIWIWIHIHIWIIHHIWH ms con-mun hngJ/wwwm ngbngmUSALom/AggllcahonNmes
SPEC NO: DSAL0864 REV NO: V.6 DATE: OCT/07/2016 PAGE: 6 OF 6
APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1201006871
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes